Honeywell T6360 User manual

HEATING CONTROLS
APPLICATION
The T6360 is a mains voltage Room Thermostat designed to give
automatic temperature control of domestic wet central heating
systems. It can be used to directly switch a circulating pump or
boiler, or to operate spring return and motor open/motor close
zone valves. The T6360 can switch electrical heating loads up
to 10A.
The T6360 thermostat can also be used for cooling applications.
4.7
T6360
ROOM THERMOSTAT
FEATURES
■
Dual diaphragm temperature
sensing element
■
Suitable for surface or switch
box mounting
■
Heat anticipator for close
temperature control
■
10 to 30˚C setpoint range
■
Change-over contact switching
(cooling loads)
■
Double insulated
OPTIONS
■
Temperature setback model
■
Tamper resistant model
■
Model with indicator lamp
■
Setting dial marked 1 to 5
■
High current rated model
■
Range stops
© Hone well Control Products and S stems, Issue 10
0014_Section 4_dft10_v4.qxd:Section 2_dft9 15/10/07 16:19 Page 15

ROOM THERMOSTAT T6360
■Installation
The T6360 thermostat must be
located where it is not subjected to
extraneous heat gains, direct sunlight
or draughts.
Fixing screws are supplied for either
surface or flush mounting box.
■Ordering Specification
T6360B1028
Standard model complete with heat
anticipator and RFI suppressor
T4360B1015
High current rated version with SPST
switching and rated at 16A (resistive).
Without heat anticipator
T6360B1069
As standard model but with tamper
resistant cover and setting dial
T6360B1036
As standard model but with indicator
lamp on front cover which is lit on a
call for heat
T6360B1085
As standard model but with setting dial
marked 1 to 5
T4360E1018
Model with temperature setback heater
(fixed at 6°C) and SPST switching,
complete with anticipator heater and
RFI suppressor
F42007562-001
Accessory footprint for use when
replacing T6060 thermostats
F42006646-001
Bag assembly containing 20 range
stops and installation instructions
F42007110-001
Opaque tamperproof dial cover
TG510A1001
Lockable, clear plastic thermostat
cover. Backplate and spare keys inc
■Specification
Voltage Rating : 230VAC, +/-10%, 50…60Hz
Switch Rating Terminal 3 : 10A resistive, 3A inductive
Terminal 4 : 6A resistive, 2A inductive
Switch Type : Single pole, double throw (SPDT)
Temperature Setting Range : 10 to 30˚C
Temperature Control Accuracy : ± 0.5˚C at 3˚K/hour with anticipator
Storage Conditions : -20 to 55˚C
Humidity : 10 to 90% RH, non-condensing
Standards : CE marked
EC Directive : EN60730-1 (1995), EN55014-1
(1997), EN55014-2 (1996)
■Dimensions (mm)
■Wiring
Note:
1. Switching contacts are shown in the
normally open position – i.e. no heat
demand
2. Typical heating loads –
i) T4360B – electric heaters
ii) T6360/T4360E – motorised valves
84
84 37
T4360E
T
Terminal 3 :10(3)A max.
T
230V
ST9000
50Hz
230V
50Hz
(2.ii)
H
HEATING
LOAD
SETBACK
HEATER
N
6
5
3
2
1
L
N
N
N
L
T4360B
T
Terminal 3 :16A max.
T
(2.i)
230V
50Hz
HEATI NG
LOAD
(
N
3
1L
T6360B
T
Terminal 3 :10(3)A max.
Terminal 4 :6(2)A max.
(
230V
50Hz
(2.ii)
(
HEATI NG
LOAD
4
3
2
1
N
N
L
© Hone well Control Products and S stems, Issue 10, 4.7
0014_Section 4_dft10_v4.qxd:Section 2_dft9 15/10/07 16:19 Page 16