Hoover HV-C60RS User manual

Model Number HV-C60RS
60 cm Slideout Rangehood
INSTRUCTION MANUAL
E209
AFTER SALES SUPPORT
(AU) 1300 886 649 (NZ) 0800 836 761

22After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Contents
03 General Safety Instructions
06 Product Overview
07 Installation
16 Instructions
17 FAQs & Troubleshooting Guide
18 Other Useful Information

3
3
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Important installation precautions
• WARNING: All electrical work associated with the installation of this
rangehood must be carried out by a licensed electrician.
• WARNING: This rangehood must be installed by a suitably qualified
person in strict accordance with all instructions in this manual.
• Ventilation: As heat, steam and moisture will be created during use of the
appliance, take care to avoid injury and ensure that the room is adequately
ventilated. Additional ventilation may be required if the appliance is going
to be used for prolonged periods of time or at the same time as appliances
burning gas or other fuels. Consult your installer if you are in doubt about
the amount of ventilation required.
• Electrical fittings and cables: Do not allow electrical fittings or cables
to come into contact with areas on the associated equipment (cooktop or
stove) that get hot.
• Air discharge: The exhaust air must not be discharged into a flue which is
used for exhausting fumes from appliances burning gas or other fuels.
• External air evacuation: Make sure to follow your local laws that apply to
external air evacuation when installing and using the rangehood.
• Clearances: This rangehood is designed for top-mounted installation
in a cabinet above a cooking appliance, at a distance of 65-75 cm from
the cooking surface. Refer to pages 7–15 for comprehensive installation
instructions.
• Installation: Install the rangehood onto the bottom of the cupboard and
secure it in place with the four supplied ST5*50 mm screws.
WARNING: Failure to install the screws or fixing device in accordance with
these instructions may result in electrical hazards!
IMPORTANT SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before first use, even if you are familiar with this
type of product. The safety precautions enclosed herein reduce the risk of
fire, electric shock and injury when correctly adhered to. Keep the manual in
a safe place for future reference, along with the completed warranty card and
purchase receipt. If you sell or transfer ownership of this product, pass on
these instructions to the new owner.
Always follow basic safety precautions and accident prevention
measures when using an electrical appliance, including the following:
General Safety Instructions (Cont.)

44After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
General Safety Instructions (Cont.)
Electrical safety and usage conditions
• Voltage and frequency: Before plugging the unit into an appropriate electrical
outlet, make sure your outlet voltage and circuit frequency correspond to the
voltage stated on the appliance rating label.
• Power cord: Check the cord regularly for damage. Do not use the appliance
if any part, including the cord, is damaged. A damaged cord must be replaced
by the manufacturer or a similarly qualified person in order to avoid a hazard.
• Winding the cord: If winding the power cord, avoid tight bends as this could
damage the cord.
• Disconnect: Before cleaning the rangehood, make sure to switch it off and
unplug it from the electrical supply. Do not disconnect the appliance with wet
hands. Grip by the plug, do not pull by the cord when disconnecting.
• Domestic use only: This rangehood is designed for indoor domestic use only.
It can be built into a standard kitchen cabinet or housing unit following the
instructions. Not intended for commercial, trade or industrial use.
• Intended purpose: Only use this rangehood for its intended purpose, in its
intended environment and as described in this manual. Any other use may
cause fire, electric shock or injury.
• Use common sense: These instructions are not intended to cover every
possible condition and situation. As with any electrical household appliance,
common sense and caution are therefore always recommended when
installing, operating and maintaining the equipment.
• Usage restriction: This rangehood is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Children: Supervise children to ensure they do not play with the appliance. Close
supervision is necessary when any appliance is used by or near children.
• CAUTION: Take care when the rangehood is operating simultaneously with
an open fireplace or burner that depend on air from the environment and are
supplied by other than electrical energy, as the rangehood removes air from
the environment which a burner or fireplace needs for combustion.
• Ventilation: The rangehood removes air from the environment during use.
Always provide adequate ventilation for safe operation of the rangehood. This
is particularly important when the rangehood is used at the same time as flued
heaters burning gas or other fuels.
• Unattended: Do not leave the rangehood unattended during use.
• No timer: The appliance is not intended to be operated by means of an
external timer or separate remote control system.

5
5
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
General Safety Instructions (Cont.)
• CAUTION: No open flame cooking! Do not use an open flame for cooking
underneath this rangehood; do not flambé under the rangehood. Open
flames can damage the filters and present a fire hazard.
• After use: Always switch off the rangehood after use and before cleaning.
• CAUTION: Do not touch the light bulbs after the appliance has been used
as they may be hot. Let them cool down before cleaning and maintenance.
• CAUTION: Accessible parts may become hot when used with cooking
appliances.
• WARNING: Fire risk! Clean your rangehood regularly as instructed in this
manual. There is a fire risk if cleaning is not carried out in accordance with
the instructions.
• Cleaning: Before cleaning the rangehood or carrying out maintenance,
make sure the operation and light switches are set to the “0” position and
the rangehood is disconnected from the power supply. Wipe the exterior
surface of the rangehood regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or with a sponge dampened
with water and a little non-abrasive liquid detergent.
• No steam cleaning: Never use a steam cleaner for cleaning the appliance.
• Filter maintenance: The aluminium mesh filters must be cleaned regularly
(at least every two months) in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as grease and grime can impede the
airflow. If you are using the rangehood with the air recirculating back into
the room, ensure to change the charcoal filters regularly (every three to six
months, depending on usage). Refer to pages 18–19 for comprehensive
cleaning instructions.
• Filters: Do not check the status of the filters while the rangehood is in use.
• Lamp: The appliance contains a rectangular 1.5 W LED Lamp (100 V - 240 V,
33.2 x 120 mm). When it needs replacing, only replace it with a lamp of the
same type and wattage. Refer to page 19 for replacement instructions, and
page 20 for information on how to purchase a replacement lamp.
• Damage: Do not use the rangehood if any part, including the supply
cord, has been damaged, is faulty or does not work properly. Only have it
repaired by an authorised service centre. Incorrect repair could expose you
to the risk of electric shock, fire or injury. Prolonged use of the unit in such
conditions could cause fire or electrocution. In case of damage, contact our
after sales support line for advice.
• Misuse: We assume no liability for any eventual damages caused by incorrect
installation, product misuse or noncompliance with the instructions.

66After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
NOTE: Due to continued product improvement, images and illustrations in this manual
may vary slightly from the product purchased. All images in this manual are for
reference purposes only. Parts are not necessarily pictured to scale.
1
2
3 4 57
Product Overview
Scope of delivery
Rangehood
1 Rangehood housing
2 Slide out front panel (fascia)
3 Inner aluminium mesh filter
4 Outer aluminium mesh filter
5 Light
6 Fan speed switch [ II / O / I ]
7 Light switch [ / (Blank) ]
Installation kit (individual parts are illustrated opposite)
Documentation (not shown)
Instruction manual
Quick start guide
Warranty card
6

7
7
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Description Part Quantity
Rangehood 1
Screws
(ST5*50) 4
Wall plugs 4
Flue outlet adaptor 1
Installation kit
The installation kit contains the following parts (shown not to scale):
Installation
Unpacking
• This product has been packaged to protect it against transportation damage.
Unpack the appliance and remove all packaging materials from around the
rangehood. Keep all packaging materials in a safe place. It will help prevent
any damage if the product needs to be transported in the future, and you can
use it to store the appliance. Whenever possible, reuse the carton and recycle
it when disposing of the packaging materials.
• Plastic wrapping can be a suffocation hazard for babies and young children,
so ensure all packaging materials are out of their reach and disposed of safely.

88After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Installation (Cont.)
WARNING!
• All electrical work associated with the installation of this rangehood must
be carried out by a licensed electrician. Please note the details of your
licensed installer on page 22 of this manual.
• This rangehood must be correctly installed by a suitably qualified
person in strict accordance with all applicable rules and regulations and
following the instructions in this manual.
• Do not try to install the rangehood yourself; doing so will expose you to
danger and void the warranty. Improper installation, adjustment, alteration
or service can cause injury or damage. We decline any responsibility
for injury or damage, to persons or property, as a result of improper
installation.
Important installation advice
Product dimensions:
NOTE: All dimensions in Fig. 1 are in millimetres (mm).
Ø 118
480
175
40
280
135
423
595
238
85
Fig. 1

9
9
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Installation height
This rangehood is designed for top or side installation above a cooking
appliance. Mounting instructions follow on pages 13-14. For optimum
performance, the rangehood should be installed at a distance of 650-750 mm
from the cooking surface (Fig. 2). (See Fig. 12 page 12, for detailed minimum
distance requirements.)
Installation (Cont.)
650 mm
to
750 mm
Ducting mode
Recirculating mode
Venting knob position
Venting options
• When installing the
rangehood, please check
and ensure that the two
levers on the motor are set
to the desired venting mode
(Fig. 3): “DUCTING” or
“RECIRCULATING”.
• In most cases, steam should
be vented outside (Fig. 5,
outdoor ducting mode),
using an exhaust ducting
pipe. However, if this is not
possible, the steam can
be vented back into the
kitchen (Fig. 4, recirculating
mode), using odour-
absorbing charcoal filters
(for information on how to
purchase these, see page
20).
Fig. 2
Fig. 3
Fig. 4 Fig. 5

10
10 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Outdoor ducting mode
This is the recommended extraction mode wherever possible for optimum
performance. If you are able to install the exhaust duct to vent the air outside
and operate your rangehood in outdoor ducting mode, proceed as follows:
• Ensure the vent cover is in place, as indicated below (Fig. 6).
• Remove the aluminium mesh filters from the underside of the rangehood
(Fig. 7) and set the two levers in the centre of the motor housing to the
“DUCTING” position (see Fig. 3).
• Install the flue outlet adaptor to the top of the rangehood, by aligning the
three tabs of the adaptor with the three insertion points on the top of the
rangehood (Fig. 8). Then, turn the adaptor clockwise until it is firmly in place
and will not turn any further.
Installation (Cont.)
Fig. 7 Fig. 8
Fig. 9
• Install the exhaust ducting pipe to the outlet
on the top of the rangehood and vent to the
outside. You can use either a flexible or rigid
pipe with a 120 mm diameter (Fig. 9).
NOTE: When using the outdoor ducting
mode, do not use charcoal filters, as they
are not required. For information on how to
remove charcoal filters, see page 11.
Fig. 6

11
11
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Recirculating mode
This mode is the default setting. The rangehood must operate with charcoal
filters installed, as it will vent the air back into the kitchen. The vent cover
should be removed when using this mode (see Fig. 6).
To ensure that the mode is correct, remove the aluminium mesh filters (Fig. 7)
and check that the two levers are in the “RECIRCULATING” position (Fig. 4).
Charcoal filters
• If you intend to use the rangehood with the air recirculating back into the
kitchen, it is important that you use the charcoal filters to absorb some of
the cooking odours.
• To purchase these filters, please contact our after sales support team using
the information at the bottom of the page.
Removing and installing charcoal filters
• To install the charcoal filters, first remove the aluminium mesh filters
(Fig. 7), then align the charcoal filters with the centre of the motors, push
upwards and turn clockwise (Fig. 10) until they lock into place. Replace the
mesh filters.
• To remove the charcoal filters, first remove the aluminium mesh filters
(Fig. 7), then turn anticlockwise (Fig. 11) and gently pull down. Replace the
mesh filters.
NOTE: These charcoal filters cannot be washed and reused. When there
is insufficient suction power, or the recirculated air starts to smell, please
purchase and install replacement filters.
Installation (Cont.)
Fig. 10 Fig. 11

12
12 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Installation (Cont.)
Installing the rangehood
• This rangehood is designed for top or side-mounted installation in a cabinet
above a cooking appliance. For optimum performance, the rangehood should
be installed at a distance of 650-750 mm from the cooking surface (Fig. 2).
The minimum required distance is 650 mm from an electric cooktop and
650 mm from a gas cooktop (Fig. 12).
See the diagrams below for more information on the product dimensions
(Fig. 13 and Fig. 14)
According to the figure, make sure the position of hood in the cabinet. The wood strips
should be line up with the 4 keyholes slots on the top of the range hood. On the cabinet,
install 4 screws (supplied) according to the relative position of 4 key holes on the bottom
of hood. The extent of screwing should be convenience to the next installation.
Hang the hood and let it’s 4 key holes aim at screws, the 4 screws should be in the
narrow parts of key holes. Screws should be fasten firmly, make sure that the installation
between the hood and cabinet is enough fasten.
Install screws in the security holes, in case of front and back moving of hood, so that
the using is safer.
69
155
40
400
80
238
85
480
�423
Security�hole
175
40
280
595 135
OPTIONAL�28/25/18
400
115
80
155
40
69
Ø 118
480
175
40
280
135
423
595
238
85
153
480
Min. Min.
650
Min.
650 mm
Min.
650 mm
175
Fig. 13
Fig. 14
Fig. 12

13
13
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Installation (Cont.)
Method 1: Top-mounting this appliance
• With a 10 mm drill bit, pre-drill four holes, 50 mm deep, into the base of
a cabinet or into the ceiling using the diagram on page 12 (Fig. 14). They
should be 480 mm apart in length and 153 mm apart in depth. Insert the
supplied wall plugs.
NOTE: You will also need to make an opening for the power cord and plug
and, if the rangehood is to be ducted to the outside, a hole for the ducting.
• In accordance with Fig. 15, align the position of the rangehood with
the cabinet. Open the fascia fully for a clearer view, and to ensure the
rangehood’s holes for the screws align with the pre-drilled holes in the
cabinetry.
• Install the four screws (supplied) through the range hood and into the plugs
in the cabinetry or ceiling. Ensure they are fastened securely and that the
cabinet or ceiling can withstand the weight of the rangehood.
According to the figure, make sure the position of hood in the cabinet. The wood strips
should be line up with the 4 keyholes slots on the top of the range hood. On the cabinet,
install 4 screws (supplied) according to the relative position of 4 key holes on the bottom
of hood. The extent of screwing should be convenience to the next installation.
Hang the hood and let it’s 4 key holes aim at screws, the 4 screws should be in the
narrow parts of key holes. Screws should be fasten firmly, make sure that the installation
between the hood and cabinet is enough fasten.
Install screws in the security holes, in case of front and back moving of hood, so that
the using is safer.
69
155
40
400
80
238 85 480
�423
Security�hole
175
40
280
595 135
OPTIONAL�28/25/18
Fig. 15
WARNING: Failure to install the screws or fixing device in accordance with
these instructions may result in electrical hazards!
WARNING: When cutting or drilling into wall or ceiling, ensure that you do not
damage electrical wiring or other hidden utilities.

14
14 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
WARNING: Failure to install the screws or fixing device in accordance with
these instructions may result in electrical hazards!
Method 2: Back-mounting this appliance
• With a 10 mm drill bit, pre-drill four holes, 50 mm deep, into the wall, using
the diagram on page 12 (Fig. 13). They should be 400 mm apart horizontally
and 115 mm apart vertically. Insert the supplied wall plugs
NOTE: You will also need to make an opening for the power cord and plug
and, if the rangehood is to be ducted to the outside, a hole for the ducting.
• In accordance with Fig. 16, align the position of the rangehood with the wall.
Open the fascia fully for a clearer view, and to ensure the rangehood’s holes
for the screws align with the pre-drilled holes.
• Install the four screws (supplied) through the range hood and into the wall
plugs in the wall. Ensure they are fastened securely and that the wall can
withstand the weight of the rangehood.
WARNING: When cutting or drilling into wall or ceiling, ensure that you do not
damage electrical wiring or other hidden utilities.
Installation (Cont.)
According to the figure, make sure the position of hood in the cabinet. The wood strips
should be line up with the 4 keyholes slots on the top of the range hood. On the cabinet,
install 4 screws (supplied) according to the relative position of 4 key holes on the bottom
of hood. The extent of screwing should be convenience to the next installation.
Hang the hood and let it’s 4 key holes aim at screws, the 4 screws should be in the
narrow parts of key holes. Screws should be fasten firmly, make sure that the installation
between the hood and cabinet is enough fasten.
Install screws in the security holes, in case of front and back moving of hood, so that
the using is safer.
69
155
40
400
80
238 85 480
�423
Security�hole
175
40
280
595 135
OPTIONAL�28/25/18
Fig. 16

15
15
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
• Ensure that the rangehood is horizontally aligned. Do not use this
appliance if it is not installed at a horizontal angle (Fig. 17). We recommend
using a spirit level or similar device to ensure that the rangehood is level
before use.
Installation Notes:
Installation (Cont.)


Fig. 17

16
16 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Switching on/off
Make sure the rangehood is properly connected to the power supply and the
power is switched on at the outlet.
After the rangehood has been properly installed, insert the power plug into
an appropriate electrical outlet and let the unit run for a few minutes prior to
using it while cooking.
This switch turns the rangehood lights either on or off.
Turns the rangehood lights ON.
(Blank) Turns the rangehood lights OFF.
This button switches the rangehood on and toggles between the fan
speed settings: HIGH, LOW, OFF.
=Turns on the fan motors to HIGH speed for maximum
extraction.
OTurns off the fan motors for no extraction; the rangehood is
switched OFF.
– Turns on the fan motors to LOW speed for minimum extraction.
Operation
• Pull out the front panel.
• Switch the rangehood lights on, if desired.
• Select the desired fan speed. The rangehood will start operation at the set
fan speed.
• Close the front panel and the rangehood will stop working.
• The next time the front panel is pulled back out, the rangehood will start
working at the previously set level.
NOTE: The rangehood will only operate once the slide-out panel is pulled
outwards towards the kitchen.
Instructions
：
：

17
17
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Problem Possible cause Solution
The
extractor
fan does not
work.
There is no electrical
current in the network.
Check with other appliances that your
electricity supply is in working order.
The rangehood fan
motors are switched off.
Check and ensure that the fan speed
switch is set to “–” or “=”.
The slide-out panel has
not been pulled out.
Make sure that the slide-out rail is
pulled out.
There is
insufficient
suction
power.
The aluminium mesh
filters are clogged.
Remove and clean the aluminium
mesh filters and reinstall them when
they are dry.
Wrong suction speed. Select suction speed “=” if speed “–”
was selected.
The charcoal filters
need to be replaced.
If the rangehood is installed for
recirculation, check that the charcoal
filters are still effective. They need to be
replaced if food smells start to become
noticeable within your kitchen.
The air outlet is
blocked, or the exhaust
duct is too long,
bending too much or
has collapsed.
If the rangehood is installed to vent
outside, check that the ducting and
outlets are free of blockages. Also
ensure that the duct is in proper
working condition.
Insufficient ventilation. Make sure your kitchen is adequately
vented to allow the entry of fresh air.
The
rangehood
has
switched
off during
operation.
The safety cut-out
device has been
tripped.
Turn off the rangehood and wait for
the device to reset.
If the rangehood has been installed
below the height levels indicated in
the “Installation” section, the motor
will cut out frequently, which may
damage the rangehood.
The lights do
not work.
The lamps are loose,
or burnt out.
Tighten the lamps, or replace them, if
necessary.
If you experience problems with your rangehood, or it appears not to be
operating correctly, check in the list below for answers to frequently asked
questions. If none of the solutions offered help you solve your problem,
please contact our after sales support centre for advice using the details at
the bottom of the page. Do not attempt to repair the appliance yourself!
FAQs & Troubleshooting Guide

18
18 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood regularly using a soft cloth
moistened with a household solvent such as methylated spirits, or with a
sponge dampened with water and a little non-abrasive liquid detergent.
Cleaning the filters
The aluminium mesh filters must be cleaned regularly in order to prevent a fire
hazard. Regular cleaning also ensures better efficiency, as grease and grime can
impede the airflow. We recommend cleaning them at least every two months.
• Push in the plastic opening latch and take the filters out of their frames (Fig. 18).
Other Useful Information
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out maintenance, make sure
the operation and light switches are set to the “ 0 ” position and the
rangehood is disconnected from the power supply.
• It is important to clean the filters regularly as oil and food residues can
become a fire hazard.
• Never use a steam cleaner to clean any part of the rangehood.
Fig. 18
• Wash the filters thoroughly in warm, soapy water. For best results, leave
them to soak, wash and rinse with warm water. The aluminium mesh filters
may also be cleaned in a dishwasher. After cleaning, leave the filters to dry
completely before reinstalling them into the appliance.
WARNING: Never reinstall the filters when they are still wet.
NOTE: The aluminum panels may slightly change colour after several
washes. This is not a fault and no cause for concern. It does not affect
performance and does not warrant replacement of these parts.

19
19
After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Charcoal filters
If you are using the rangehood with the air recirculating back into the room,
two charcoal filters must be installed before use.
The charcoal filters absorb cooking odours and must be changed regularly.
How often you need to change the filters depends on your usage. We
recommend changing them every three to six months. An activated charcoal
filter cannot be washed or recycled; it must be replaced with a new one.
To obtain replacement filters, contact our after sales support center and
arrange for purchase – see page 20 for details.
NOTE: The suction power will be lowered with charcoal filters installed.
NOTE: To remove and/or install new filters, please see page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as follows:
• Disconnect the appliance from the power supply.
• Slide out the front panel for easier access and remove the two aluminium
mesh filters (Fig. 18 and Fig. 19).
• Remove the light by pulling it from the ragehood body (Fig. 20) and
disconnect the connector to the light.
• Replace the bulb with one of the same type (self-ballasted LED module,
100 V - 240 V, 33.2 x 120 mm) and wattage (max. 1.5 W), as illustrated
(Fig. 20). Ensure the cable is connected correctly.
• Replace the metal filters.
Other Useful Information (Cont.)
Fig. 19 Fig. 20

20
20 After Sales Support
(AU) 1300 886 649 (NZ) 0800 836 761 | tempo.org/support
Compliance
This appliance has been fully tested and meets all requirements as set out by
standards AS/NZS 60335.1 and AS/NZS 60335.2.31.
Technical specifications
Rated voltage / frequency 220–240 V~ / 50 Hz
Rated power 211.5 W
Dimensions (closed) (mm) 175 (H) x 595 (W) x 280 (D)
Extended depth (mm) 415
Height of front panel (mm) 43
Weight (approx.) 9.05 kg
Motor Input power 210 W
Lamp power 1.5 W
Filters 2 Aluminium mesh filters
Service, repair and spare parts
If the appliance is damaged, do not attempt to repair it yourself. If it requires
repair or service, please contact our after sales support centre to arrange for
examination and repair.
Our after sales support centre stocks a range of spare parts for the appliance.
For more information, or to purchase a spare part, contact the centre using
the details at the bottom of the page.
Other Useful Information (Cont.)
The RCM Mark (Regulatory Compliance Mark) indicates that the product
complies with the relevant guidelines of the ACMA as well as corresponding
government requirements for the safety of electrical devices.
E209