Hoshizaki FM-170AFE User manual

89/336
73/23
92E2GA20A (051807)
MODULAR ICE MAKER
MACHINEAGLACEMODULAIRE
EISBEREITER FÜR SEPARATEN VORRATSBEHÄLTER
IJSMACHINE MET LOSSE OPSLAGBUNKER
MAQUINA DE CUBITOS MODULAR
FABBRICATORE MODULARE DI GHIACCIO
INSTALLATION MANUAL
NOTICE D’INSTALLATION
INSTALLATIONSANLEITUNG
INSTALLATIE VOORSCHRIFT
MANUAL DE INSTALACION
MANUALEPERL’INSTALLAZIONE
FOR QUALIFIED INSTALLER ONLY
RESERVEAL’INSTALLATEUR
FÜR DEN INSTALLATEUR
VOOR DE BEVOEGDE INSTALLATEUR
SOLAMENTE PARAINSTALADOR CUALIFICADO
SOLTANTO PER INSTALLATORI QUALIFICATI
FM-170AFE
FM-170AFE-N

ENGLISH
1
IMPORTANT
1. Inordertocarryoutsafeandproperinstallation
of the product, please read this booklet
carefullybeforehandandfollowtheinstructions
contained within.
2. On completion of the installation, start up the
icemaker to check for any abnormalities, and
instruct the user on how to use and maintain
the icemaker in accordance with the
Instruction Manual.
3. Thisbookletshouldbehandedovertotheuser
after the installation and be preserved by the
user together with the Instruction Manual for
any further consultation that may be
necessary.
WARNING
The installation must be carried out by
qualified personnel,in accordance withcurrent
regulations, according to the manufacturer’s
instructions.
1. UNPACKING
WARNING
Children should not be allowed in reach of the
packagingelements (plastic bags and expanded
polystyrene) as they are potential sources of
danger.
CAUTION
1. Do not lift or manoeuvre the carton by using
the shipping bands.
2. Removeshippingcarton,tape(s)andpacking.
If packing material is left in the icemaker, it
will not work properly.
Note: This icemaker needs a Storage Bin. The
recommendedStorage Bin isHOSHIZAKI ICE
STORAGE BIN, Model B-300SF(PF) or B-
500SF(PF)withTopKit-8C, B-700SF(PF)with
Top Kit - 22C, or B-900SF(PF) with Top Kit -
22C and Top Kit - 8C.
1) After removing the packaging, make sure that the
icemakerandtheStorageBinareingood condition.
If in doubt, please do not use the equipment but
applytoprofessionally qualified personnel. See the
instruction sheet attached to the Storage Bin for its
unpacking and installation guidelines.
2) Remove the shipping tape holding the panels.
3) Remove the Front, Top and Side Panels. See Fig.
2.
4) Remove the package of accessories, and check
the contents:
a) Installation Kit
Inlet Hose 1
Outlet Hose 2
b) Mounting Bracket 2
5) Remove the protective plastic film from the panels.
If the icemaker is exposed to the sun or to heat,
remove the film after the icemaker cools.
2. LOCATION
IMPORTANT
1. This icemaker isnot intended foroutdoor use.
Normaloperatingambienttemperatureshould
bewithin 5°Cto40°C. Normaloperatingwater
temperature should be within 5°C to 35°C.
Operation of the icemaker, for extended
Top Panel: Remove the screw(s). Lift off.
Front Panel: Remove the screw. Lift up and
pull toward you.
Side Panel: Remove the screw. Pull
slightly toward you, and lift off.
Fig. 2
Fig. 1
Top Panel
Side Panel
Front Panel
Power Supply Cord
Top Panel
Operation Panel
Air Filter
Front Panel
Louver

ENGLISH
2
periods, outside of these normal temperature
ranges may affect production capacity.
2. The icemaker should not be located next to
ovens, grills or other high heat producing
equipment.
3. The location should provide a firm and level
foundation for the equipment.
4. Allow 15 cm clearance at rear and sides for
properaircirculation andeaseofmaintenance
and/or service should they be required. Allow
60 cm clearance on top to allow for removal of
theAuger.
5. This appliance is not suitable for installation
in an area where a water jet could be used
and where dripping is not allowed.
6. Do not place anything on top of the icemaker
or in front of the Louver.
7. This icemaker will not work at subfreezing
temperatures. Topreventdamagetothewater
supply line, drain the icemaker when air
temperature is below zero (see “II. 2.
PREPARING THE ICEMAKER FOR LONG
STORAGE” in the instruction manual).
8. The noise from this icemaker is 55 dB or less.
3. INSTALLATION
* Incorrect installation can cause harm to people,
animalsorthings,forwhich the manufacturer cannot
be held responsible.
1)Fullyscrew in the four legsprovided(binaccessory)
into the Storage Bin underside. See Fig. 3.
4) Secure the icemaker to the Storage Bin, by using
the two mounting brackets and two bolts provided.
See Fig. 4.
Fig. 5
Bottom Plate
Adjustable Legs
Adjust legs
Fig. 3
2) Position the Storage Bin in the selected permanent
site.
3) Place the icemaker on top of the Storage Bin by
holding the bottom.
4. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the
national and local electrical code requirements.
To prevent possible severe electrical shock to
individuals or extensive damage to equipment,
install a proper earth wire to the icemaker.
Remove the plug from the mains socket before
any maintenance, repairs or cleaning is
undertaken.
* This icemaker should not be installed:
a) Where the power supply is not within the range
of 220 - 240V.
b) Where theicemakercannotbeconnecteddirectly
Fig. 4
Icemaker
Mounting
Bracket
Bin
Bolt
5) Seal the seam between the icemaker and the
Storage Bin with food grade sealant.
6) Refit the Side Panels in their correct position.
7)Adjust the four legs on the bottom (adjustable from
0 to 25.4 mm) to have the icemaker perfectly
horizontal. Use the spirit level. See Fig. 5.

ENGLISH
3
into its own power supply without using an
extension cord or sharing a receptacle.
* Usually an electrical permit and services of a
licensed electrician are required.
* If the supply cord and/or the plug should need to be
replaced, it should only be done by a qualified
serviceengineer.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured Green-and-Yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the symbol or
colouredGreenorGreen-and-Yellow. Thewirewhich
is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Black.
ThewirewhichiscolouredBrownmustbeconnected
to the terminal which is marked with the letter L or
colouredRed.
* Should the socket outlets in the installation site not
be suitable for the plug supplied with your product,
the plug must be removed (cut off if it is moulded on
plug) and an appropriate plug fitted.
Ifthenon-rewirableplughasbeencutfromthepower
supply cord, it must be disposed of. There should
be no attempt to reuse it. Inserting such a plug into
a socket elsewhere presents a serious risk of
electrical shock.
*Thenon-rewirableplugmustneverbeusedwithouta
fuse cover being fitted.
The correct replacement for the detachable fuse
coverisidentifiablefromthemanufacturer’sreference
number stamped on the plug.
Supply of replacement fuse covers can be obtained
from Hoshizaki Parts/Service Centres.
Fuses should be rated at 10A and approved to BS
1362.
5. WATER SUPPLY AND DRAIN
CONNECTIONS
(For the U.K. only, the connections must be in
accordance with current requirements of the Model
Water Byelaws 1986 SI No. 1147)
* Only potable water should be used for the icemaker.
* Water supply pressure should be minimum 0.5 bar
and maximum 8 bar. If the pressure exceeds 8 bar,
use a proper pressure reducing valve. Do NOT
throttle back the supply tap.
*Aplumbingpermitand servicesofalicensedplumber
may be required in some areas.
* The icemaker drain is gravity flow, so ensure drain
pipe has an adequate pitch or fall.
* Water should drain into an open trap.
1) Attach angled end of white flexible inlet hose
(accessory) to the G3/4 fitting on the rear of the
icemaker as indicated, ensuring rubber sealing
washer is correctly positioned. Hand tighten
sufficiently to provide leak free joint.
2) Attach the other end of inlet hose(s) to the water
tap, noting washer(s) is/are correctly positioned
before hand tightening as above.
Note: If filtration or treatment is used, ensure
icemaker section only is on treated water
supply, not the condenser.
3) Attach grey flexible outlet hoses (accessories) to
the R3/4 fittings as indicated, confirming fitment of
rubber washers before finally hand tightening the
joints. These pipes can be cut to length as
necessary to suit position of main drain.
Fig. 6
Water Supply
Inlet G3/4
Inlet Hose Drain Outlet
R3/4
Outlet Hose

ENGLISH
4
Fig. 7
Fig. 8
OperationPanel
Water Supply Tap
Inlet Hose
Circuit Breaker (6A) Motor Protector (3A)
Operation Switch
IMPORTANT
1. Check the conditions and quality of the ice
production.
6. START-UP PROCEDURE
1) Check that the power supply cord is disconnected.
2) Move the Operation Switch on the Operation Panel
to the “ON” position.
3) Open the water supply tap.
4) Connect the power supply and energise.
5) The following should occur in sequence:
a) Water Reservoir will fill.
b) Gear Motor will start.
c) Compressor will start.
2. Do not use ice produced in the trial run. It
might be contaminated with foreign matter in
the water circuit. Discard or flush down the
drain.
3. Clean the Storage Bin before use (see “III. 1.
CLEANING” in Instruction Manual).
7. FINAL CHECKS
1) Is installation free of water leaks?
2) Is the icemaker free from vibration?
3)Are all the panels fixed and secure?
4) Has the user been instructed on correct machine
use and handed the Instruction Manual?