Hotpoint Ariston SX100C2BK User manual

SX100C2BK
SX100C2WH
SC100C2AV
SC100C2AN
SC100C2WH
SX86C1BK
SX86C1WH
SC86C1AV
SC86C1AN
SC86C1WH
English
EN
Instructions for use

SC 86 C1
SC 100 C2
SK 86 C1
SK 100 C2

Installation
!Before installing your new sink please read this
instruction booklet carefully. It contains important
information concerning the safe operation, install-
ation and maintenance of the sink.
!It is important to keep this booklet to be able to
consult it at any time. In the event of sale, transfer or
relocation, make sure it stays with the sink so that
the new owner has information on its operation and
the relative warnings.
Positioning and connection
!Keep all packaging material out of reach of
children. It may present a choking or suffocation
hazard. (Please see Maintenance and care? -not
sure if you need this).
!Installation must be carried out in accordance with
these instructions and by professionally qualified
personnel. Incorrect installation may cause damage
to persons, animals or property.
Instructions for installing the mixer
The sink has perforation positions (marked by col-
oured adhesive) where the mixer can be installed.
Choose the mixer installation position with care, in
relation to the installation position of the sink itself.
To open your hole for mixer installation, simply knock
a screwdriver with a hammer on the point chosen.
Clean the rim of the hole with a file.
!Perforation to install the mixer is irreversible, so
take great care.
!Once the surface of the sink has been perforated,
be careful to use protective gloves.
Instructions for installing the sink
1Prepare the
sink with
the drain
installed
(see Fig. A).
Fig.A
2Apply some silicon along the entire perimeter of
the sink so that it projects 2-3 mm over the
edge (see Fig. B).
Edge of sink
Silicon
2-3 mm
Fig.B
3Insert the sink in the cut-out.
4Insert the hooks (in the kit) in the appropriate
holes in the sink.
5Tighten the hook
screws with the
screwdriver to defin-
itively anchor the
sink.
6Remove any residual
silicon outside the edge
of sink.
EN
3

Installation Maintenance and care
Instruction for installing the waste control
system , in related models:
Install the waste control knob as shown (See figure C)
!Adjust variable screw (a) and tighten the nut (b) firmly
! Adjust variable screw (a)
and tighten the nut (b)firmly
BBB
AAA
111...
222...
333...
Cleaning the sink
For the daily use it is advisable to clean the sink
using either neutral detergents or vinegar based de-
tergents.
After using and rinsing the sink it should be dried
with an absorbent cloth to avoid limestone deposits
and generate hereof whitened areas. Should these
occur use a common limestone remover or descaler
according the instructions for use on the bottle.
!Avoid leaving wet sponges, salt, corrosive
substances or very hot objects on the sink for long
periods of time. Lines and scratches may be
caused by improper use of the sink, so avoid using
it as a work surface for cutting things.
!Avoid the use of abrasives or cleansers, powdered
detergents and sponges with an abrasive surface, as
these can all scratch the surface irredeemably.it
!Never use steam or high-pressure cleaning systems
to clean your sink.
!For more stubborn stains use a cloth dampened
with methylated spirit and wipe the stains away.
Call our Parts team on 08448 225 225 or
visit www.hotpointservice.co.uk where
you can purchase a wide range of care
products to prolong and enhance the life
of your appliance
Disposal
When disposing of packaging material: observe
local legislation so that the packaging may be
reused.
EN
4

After Sales Service
EN
5
Before calling the Customer Care:
• check whether the anomaly can be solved autonomously;
• otherwise, contact the Authorized Technical Customer Care.
! Never engage non-authorized technicians.
Notify:
•the kind of anomaly;
•the sink model (Mod.);
•the serial number (S/N).
This information is on the ratings plate on the sink
After Sales Service
7 days a week service
If you need assistance, call our Hotpoint Service Centre on 08448 224 224*.
* For people calling from a BT landline, calls cost up to 5 pence per minute. Mobile and other providers changes may
vary. Open Mon. to Fri. from 08:00 to 18:30, Sat. from 08:30 to 17:30 and Sunday 09:30 to 15:30. For further
information, please contact your phone company.
For further information, visit www.hotpointservice.co.uk.