HP ProBook x360 435 G7 Assembly instructions

EL-MF877-00 Page 1
Template Revision C
Last revalidation date 09-May-2018
HPI instructions for this template are available at EL-MF877-01
Product End-of-Life Disassembly Instructions
Product Category: Notebooks and Tablet PCs
Marketing Name / Model
[List multiple models if applicable.]
HSN-I34C
HP ProBook x360 435 G7 Notebook PC
HP ProBook x360 435 G7
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions for the
disassembly of HPI products to remove components and materials requiring selective treatment, as defined by EU directive
2012/19/EC, Waste Electrical and Electronic Equipment (WEEE).
NOTE: Recyclers should sort plastic materials into resin streams for recycling based on the ISO 11469 plastic marking code on the
plastic part. For any questions on plastic marking, please contact HP’s Sustainability Contact.
1.0 Items Requiring Selective Treatment
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as applicable.
Item Description Notes
Quantity of
items
included in
product
Printed Circuit Boards (PCB) or Printed Circuit
Assemblies (PCA)
With a surface greater than 10 sq cm
Batteries, excluding Li-Ion batteries.
All types including standard alkaline, coin or button style
batteries
Li-Ion batteries. Include all Li-Ion batteries if more than
one is provided with the product (such as a detachable
notebook keyboard battery, RTC coin cell, etc.)
Battery(ies) are attached to the product by (check all
that apply with an “x” inside the “[ ]”):
[X] screws
[] snaps
[] adhesive
[X] other. Explain cable
NOTE: Add detailed removal procedures including
required tools in the sections 3.1 and 3.2.
2
Mercury-containing components
For example, mercury in lamps, display backlights,
scanner lamps, switches, batteries
0
Liquid Crystal Displays (LCD) with a surface greater
than 100 sq cm
Includes background illuminated displays with gas
discharge lamps
1
Cathode Ray Tubes (CRT)
0
Capacitors / condensers (Containing PCB/PCT)
0
Electrolytic Capacitors / Condensers measuring greater
than 2.5 cm in diameter or height
0
External electrical cables and cords
DC Cable for External Power Supply
1
Gas Discharge Lamps
0

EL-MF877-00 Page 2
Template Revision C
Last revalidation date 09-May-2018
HPI instructions for this template are available at EL-MF877-01
Item Description Notes
Quantity of
items
included in
product
Plastics containing Brominated Flame Retardants
weighing > 25 grams (not including PCBs or PCAs
already listed as a separate item above)
0
Components and parts containing toner and ink,
including liquids, semi-liquids (gel/paste) and toner
Include the cartridges, print heads, tubes, vent
chambers, and service stations.
0
Components and waste containing asbestos
0
Components, parts and materials containing refractory
ceramic fibers
0
Components, parts and materials containing
radioactive substances
0
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where components and
materials requiring selective treatment can be removed.
Tool Description
Tool Size (if
applicable)
Electric screwdriver (Cross)
Cross, #1
Screwdriver #2
Screwdriver #3
3.0 Product Disassembly Process
3.1 List the basic steps that should typically be followed to remove components and materials requiring selective treatment
including the required steps to remove the external enclosure:
1. Follow steps described in Disassembly instruction (file attached)
2. If parts can be removed without using a tool, remove it first
3. Use correct screwdriver and torque value before unlock the screw.
4.
5.
6.
7.

EL-MF877-00 Page 3
Template Revision C
Last revalidation date 09-May-2018
HPI instructions for this template are available at EL-MF877-01
3.2 Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items contained in the
product that require selective treatment (with descriptions and arrows identifying locations).

制表：审核： 韓言剛 周贵玲
Sta. Ver. Sta. Ver. Sta. Ver. Sta. Ver. Sta. Ver. Sta. Ver.
1 0.10 9 0.10 17 0.10
2 0.10 10 0.10 18 0.10
3 0.10 11 0.10 19 0.10
4 0.10 12 0.10 20 0.10
5 0.10 13 0.10 21 0.10
6 0.10 14 0.10 22 0.10
7 0.10 15 0.10
8 0.10 16 0.10
Sta. Ver.
A L L 0.1*
2020/2/27
首份SOP制作
王興洪
A.Current station version list:
B.Version Modify list:
Date
Content
Design
Written by:
周贵玲
Date:
2020/2/27
Page:
1 of 25
Sub-assembly name:
Primrose 拆机 SOP
Document No.:
Primrose 拆机 SOP
Revision:
0.10
MANUFACTURING PROCESS INSTRUCTIONS
MECHANICAL ASSEMBLY
MODEL : Primrose

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
1(1/1)
1. Disassemble the screws*5 on the lower of the
base according to the sequence shown in the
figure。
❖Disassemble screw*A directly up and down
❖Torque：2.5 ± 0.2 Kgf．cm
❖Do not slide the screw or withdraw the lower
cover during disassembly.
Disassemble the base screw
Cross electric screwdriver head（#1）
1

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
2(1/1)
图一
Disassembly of base cover2
Cross electric screwdriver head （#1）
1
1. Disassemble the screws*2 on the lower of the
base according to the sequence shown in the
figure。
❖Disassemble screw*A directly up and down
❖Torque ：2.5 ± 0.2 Kgf．cm
❖Do not slide the screw or withdraw the lower
cover during disassembly

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
3(1/1)
1. Use the disassembly bar to pry off the base
cover from the hinge cap and hook according
to the sequence shown in the figure, and then
place it in the material box。
2. Order of disassembly: 1→2→3,
❖The base cover magnet can not be attached
other screws.
Remove the base cover
disassembly bar 1

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
4(1/1)
1. According to the sequence shown in the
figure,remove the fixing screws*4。(figure 1)
❖Torque：1.5 ± 0.2 Kgf．cm
❖Do not slide the screw when disassembling
2. Remover battery from the machine。(figure2）
❖Lift the CR end of battery up to 45 and take it out
❖There are stops at the lower left and right
corners,which can not damage the hook and
battery
❖Take out the battery and place it in the material
box
Battery dismantling
Cross electric screwdriver head （#1）
1
1
2

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
5(1/1)
1
1. Remover the DDR shield Bracket from MB and
place it in the material box.
❖Make M/B Clips19（figure2）。
❖When taking DDR shield Bracket，do not damage
the upper M/B components.
Disassembly DDR Shield Bracket
2
Clips共19處

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
6(1/1)
1
2. Remover SSD shield Bracket from M/B。
❖Make M/B Clips 13（figure2）。
❖When taking DDR shield Bracket，do not damage
the upper M/B components.
Disassembly SSD Shield Bracket
2

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
7(1/2)
1
1. Open the buckle of the main DDR with both hands
at the same time,and the DDR will pop up to the tilt
automatically（figure2）
2.Take it out in the direction of DDR（figure3）
❖Do not operate with one hand(figure3)
❖Do not damage the M/B components.
❖When taking DDR,do not touch the PIN。
❖plug-in must not be skewed.
❖
Disassembly DDR
2
DIM1 DIM2
3
AMD-B
Lon fan 1

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
DDR disassembly specification
1. Only one ram can be taken and put at a
time,when taking and putting ,fingers can only hold
both sides of ram(figure1)。
❖do not press one side of ram and lift it up from
the other side(figure2)
❖Two or more RAM can not be taken and placed
at the same time by each hand(figure3)
❖do not take the place as figure4
❖do not press the golden finger as figure5
❖do not touch the gold finger on RAM as figure6.
7(2/2)
GOOD
NG
1
NG
NG NG
NG
4
3
2
5
6
静电气枪 1
离子风扇 1

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
8(1/1)
1
1.Remove K/b menbrance from M/b CNTR。(figure1)
❖Open the piano cover of CNTR and exit the line。
❖Do not pull K/B Membrane
❖do not press the broken line of KB
membrane(figure2)
2.Disassemble K/b backlight FPC from M/b CNTR。
(figure1)
❖Open the piano cover of CNTR and exit the line 。
❖Do not pull K/B Backlight FPC
Disassembling FFC/FPC(1)
BL
KB
2

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
9(1/1)
1
1. Remove click pad FFC from M/b CNTR 。(figure1)
❖Open the piano cover of CNTR and exit the line 。
❖Do not pull FFC
2. Remove 2nd camera FFC from M/b CNTR 。
(figure1)
❖Open the piano cover of CNTR and exit the line 。
❖Do not pull FFC
3. Remove Fingerprint FFC from M/b CNTR 。
(figure2)
❖Open the piano cover of CNTR and exit the line 。
❖Do not pull FFC
Disassembly FFC/FPC(二)
2
Click pad 2nd Camera
Finger Print

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
10(1/1)
1
1. Remove the WLAN main&aux sub antenna
connector from the module terminal block。
(figure1)
❖When taking out the antenna ,do not damage
the terminal on the antenna module
❖Exit the antenna from the hook
2. Take EDP cable CNTR。(figure1)
❖Hold the cable terminal and lift it up gently
❖Do not use too much force to prevent personnel
from damaging the cable
❖Withdraw the cable from the card hook.
3..remove the webcame cable CNTR from the M/b。
(figure2)
❖Hold the cable terminal and lift it up gently
❖Do not use too much force to prevent personnel
from damaging the cable
❖Withdraw the cable from the card hook
Disassembly EDP & WLANAntenna cables
EDP cable
2

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
11(1/1)
1
1. Remove DC-in cable from M/b CNTR
。(figure1)
❖Push back DC-in cable CNTR with both thumbs
until exiting M/B CNTR
2. Screw the holder&hinge in the order shown in the
figure。(figure2)
❖Torque：1.5 ±0.2 Kgf．cm
❖Do not slide the screw when disassembling
1. Take out the holder and place it in the material
box。
❖Take care not to damage the components。
2
Cross electric screwdriver head （#1）
1
Disassembly DC-IN cable&IO Holder
Location
post
图三
Redundant line
down plug
4
3
2
1

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
12(1/1)
1
1. Open the hinge to about 100 to 110 and place
it on the load support fixture (figure1)
2. Dismantle the screw*7 at the upper end of
hinge main。(figure2,figure3)
❖Do not scratch hinge cap during disassembly
❖Do not pull Hinge up cable
❖Do not collide with MB parts
❖Do not slide the screw
❖Screw material NO. : 6052A0010401
(M2.5x6.0)
❖Torguq：3.0 ± 0.2 Kgf．cm
3. Take out the upper part and main upper part。
2
Cross electric screwdriver head （#1）
1
L-shaped bearing support fixture
Dismantle the hingel screw on the main upper
34
312
312
4

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
13（1/1)
disassemble WLAN/WWAN/SSD
1
1. Remove the screw*1。(figure1)
❖Screw material NO.: 6052B0156201 (M2.0x2.0)
❖Torque：1.5 ± 0.2 Kgf．cm
❖Screw do not slide back when disassembling
2. Disassemble fix SSD module screw*1。(figure2)
❖Screw material NO. : 6052B0156201 (M2.0x2.0)
❖Torque：1.5 ± 0.2 Kgf．cm
❖Screw do not slide back when disassembling
3，take out WLAN Module and SSD Module
❖It’s hard to record the force when inserted
universal joint reverses。
2
Cross electric screwdriver head （#1）
1
3
4

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
14(1/1)
disassembly Thermal Module
1
1. Disassemble fixing screws*6。(figure1）
❖Torque：1.5 ± 0.2 Kgf．cm
❖Do not slide the screw when disassembling
❖It must be disassembled in the order1→2→3→4
→5→6
2. Remover the Thermal Module
❖Note that the right cooling fin is inserted obliquely
so first lift the left side,and then exit the fin。
(figure2)
2
Cross electric screwdriver head （#1）
1
Oblique loading is
required
1
23
4
Windbreak foam
5
6

Operation instruction
Fixture list(fixture specification) Qty Fixture list(fixture specification) Qty
Steps：
Document No. : Primrose disassembly SOP Station :
Operation name : Ver. : 0.10 editing date: 2020/2/27
Issuing department：
Prepared：Zhou Guiling IE
Note: in case of any abnormality, please inform the foreman of assistant immediately
15(1/1)
Dismantling FAN & Speaker Cable
Cross electric screwdriver head （#1）
1
1
1. Exit fan cable CNTR and speaker cable(figure1,2)
❖When exiting cable CNTR, do not tilt or pull it
out violently
2. Remove and fix fan module screw*1 。(figure2)
❖扭力：1.5 ± 0.2 Kgf．cm
❖Do not slide the screw when disassembling
3、Remove FAN module。
2