HPE Apollo 2000 User manual

HPE Apollo 2000 System
User Guide
Abstract
This document is for the person who installs, administers, and troubleshoots servers and storage systems. Hewlett Packard Enterprise
assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy
levels.
Part Number: 797871-006
June 2016
Edition: 6

© Copyright 2014, 2016 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services
are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting
an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is not
responsible for information outside Hewlett Packard Enterprise website.
Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
microSD is a trademark or a registered trademark of SD-3C in the United States, other countries or both.
Red Hat® is a registered trademark of Red Hat, Inc. in the United States and other countries.
VMware® is a registered trademark or trademark of VMware, Inc. in the United States and/or other jurisdictions.

Contents 3
Contents
HPE Apollo 2000 System..........................................................................................................................7
Introduction...............................................................................................................................................................7
Component identification ..........................................................................................................................8
Chassis front panel components ..............................................................................................................................8
Chassis front panel LEDs and buttons .....................................................................................................................9
Chassis rear panel components.............................................................................................................................10
Chassis rear panel LEDs........................................................................................................................................11
Node rear panel components .................................................................................................................................12
Node rear panel LEDs and buttons ........................................................................................................................13
Power fault LEDs....................................................................................................................................................15
System board components.....................................................................................................................................15
System maintenance switch ........................................................................................................................16
NMI functionality..........................................................................................................................................17
DIMM slot locations .....................................................................................................................................17
Fan locations ..........................................................................................................................................................18
Drive bay numbering ..............................................................................................................................................18
HPE Apollo r2200 Chassis drive bay numbering.........................................................................................18
HPE Apollo r2600 Chassis drive bay numbering.........................................................................................19
HPE Apollo r2800 Chassis drive bay numbering.........................................................................................20
M.2 SATA SSD bay numbering ...................................................................................................................21
Hot-plug drive LED definitions................................................................................................................................22
Hot-plug drive LED definitions.....................................................................................................................22
Low-profile LFF hot-plug drive LED definitions............................................................................................23
Accelerator numbering ...........................................................................................................................................24
RCM module components......................................................................................................................................25
RCM module LEDs.................................................................................................................................................25
PCIe riser board slot definitions .............................................................................................................................26
Operations ..............................................................................................................................................32
Power up the nodes ...............................................................................................................................................32
Power down the node.............................................................................................................................................32
Remove the node from the chassis........................................................................................................................32
Remove the RCM module ......................................................................................................................................34
Remove the power supply......................................................................................................................................34
Remove the security bezel .....................................................................................................................................35
Removing the drive ................................................................................................................................................35
Remove the chassis access panel .........................................................................................................................36
Install the chassis access panel .............................................................................................................................37
Remove the chassis from the rack .........................................................................................................................38
Remove the rear I/O blank .....................................................................................................................................39
Install the rear I/O blank .........................................................................................................................................40
Remove the air baffle .............................................................................................................................................41
Install the air baffle .................................................................................................................................................42
Remove the bayonet board assembly....................................................................................................................43
Install the bayonet board assembly........................................................................................................................45
Remove the PCI riser cage assembly ....................................................................................................................48
Single-slot left PCI riser cage assembly ......................................................................................................48
Single-slot 1U node right PCI riser cage assemblies ..................................................................................49
FlexibleLOM 1U node riser cage assembly.................................................................................................50
Single-slot 2U node PCI riser cage assembly .............................................................................................51
FlexibleLOM 2U node riser cage assembly.................................................................................................52
Three-slot riser cage assemblies.................................................................................................................52
Setup ......................................................................................................................................................54

Contents 4
Planning the installation .........................................................................................................................................54
Optional services.........................................................................................................................................54
Optimum environment .................................................................................................................................54
Server warnings and cautions .....................................................................................................................56
Rack warnings.............................................................................................................................................57
Unpacking the system .................................................................................................................................57
Installation overview ...............................................................................................................................................57
Installing hardware options.....................................................................................................................................58
Installing the chassis into the rack..........................................................................................................................58
Chassis component installation..............................................................................................................................60
Installing a node into the chassis ................................................................................................................60
Installing a drive...........................................................................................................................................60
Installing the power supplies .......................................................................................................................60
Powering up the chassis ........................................................................................................................................61
HPE Advanced Power Manager (optional).............................................................................................................61
Connecting the optional HPE APM module.................................................................................................61
Powering on and selecting boot options in UEFI Boot Mode .................................................................................62
Installing the operating system...............................................................................................................................62
Installing the system software ................................................................................................................................63
Power capping........................................................................................................................................................63
Power capping modes.................................................................................................................................63
Configuring a power cap..............................................................................................................................64
Drive bay mapping for the HPE Apollo r2800 Chassis...........................................................................................65
Factory default configuration .......................................................................................................................65
Mapping drive bays .....................................................................................................................................66
Registering the server ............................................................................................................................................66
Hardware options installation..................................................................................................................67
Introduction.............................................................................................................................................................67
Security bezel option ..............................................................................................................................................67
Drive options ..........................................................................................................................................................67
Removing a drive blank...............................................................................................................................68
Installing a hot-plug drive.............................................................................................................................68
Node blank .............................................................................................................................................................69
RCM module ..........................................................................................................................................................70
RCM 2.0 to 1.0 adapter cable ................................................................................................................................73
Redundant fan option .............................................................................................................................................74
Fan population guidelines............................................................................................................................74
Installing the fan option................................................................................................................................75
Memory options......................................................................................................................................................76
Memory and processor information .............................................................................................................76
SmartMemory..............................................................................................................................................78
Memory subsystem architecture..................................................................................................................78
Single-, dual-, and quad-rank DIMMs..........................................................................................................79
DIMM identification......................................................................................................................................79
Memory configurations ................................................................................................................................80
General DIMM slot population guidelines....................................................................................................80
Identifying the processor type......................................................................................................................81
Installing a DIMM.........................................................................................................................................82
SATA and Mini-SAS cable options.........................................................................................................................82
PCI riser cage assembly options............................................................................................................................84
Single-slot left PCI riser cage assembly option ...........................................................................................84
Single-slot 1U node right PCI riser cage assembly options.........................................................................86
Single-slot 2U node PCI riser cage assembly option ..................................................................................88
FlexibleLOM 1U node riser cage assembly option......................................................................................89
FlexibleLOM 2U node riser cage assembly option......................................................................................91
Three-slot riser cage assembly options.......................................................................................................93
Controller options ...................................................................................................................................................96
Storage controller installation guidelines.....................................................................................................97
Installing the HPE Smart Storage Battery ...................................................................................................97
Installing the storage controller and FBWC module options........................................................................99

Contents 5
Accelerator options...............................................................................................................................................104
Accelerator power setting switch...............................................................................................................104
Accelerator population rules......................................................................................................................104
Supported riser cage assemblies and accelerator power cables ..............................................................105
Installing one accelerator in a FlexibleLOM 2U node riser cage assembly...............................................105
Installing two accelerators in a three-slot riser cage assembly .................................................................109
M.2 SATA SSD enablement board.......................................................................................................................124
Processor and heatsink........................................................................................................................................126
Dedicated iLO management port module option..................................................................................................130
Enabling the dedicated iLO management module.....................................................................................131
HP Trusted Platform Module option .....................................................................................................................132
Installing the Trusted Platform Module board............................................................................................133
Retaining the recovery key/password........................................................................................................134
Enabling the Trusted Platform Module ......................................................................................................134
Cabling..................................................................................................................................................135
Chassis cabling ....................................................................................................................................................135
Front I/O cabling........................................................................................................................................135
Drive backplane power cabling..................................................................................................................136
RCM 2.0 cabling........................................................................................................................................137
Fan power cabling .....................................................................................................................................138
Fan module cabling ...................................................................................................................................139
HPE Smart Storage Battery cabling ..........................................................................................................139
Node cabling ........................................................................................................................................................140
SATA and mini-SAS cabling......................................................................................................................140
FBWC module cabling...............................................................................................................................142
Accelerator cabling...............................................................................................................................................144
Accelerator cabling in the FlexibleLOM 2U node riser cage assembly .....................................................144
Accelerator cabling in a three-slot riser cage assembly ............................................................................145
2-pin adapter cables..................................................................................................................................148
Software and configuration utilities .......................................................................................................149
Server mode.........................................................................................................................................................149
Product QuickSpecs ..................................................................................................................................149
HPE iLO.....................................................................................................................................................149
Active Health System ...........................................................................................................................................149
iLO RESTful API support...........................................................................................................................150
Integrated Management Log .....................................................................................................................151
HPE Insight Remote Support ....................................................................................................................151
HPE Insight Remote Support central connect......................................................................................................151
HPE Insight Online direct connect.............................................................................................................151
Insight Online.............................................................................................................................................152
Intelligent Provisioning...............................................................................................................................152
HPE Insight Diagnostics.......................................................................................................................................152
HPE Insight Diagnostics survey functionality .......................................................................................................152
Erase Utility ...............................................................................................................................................153
Scripting Toolkit for Windows and Linux....................................................................................................153
Service Pack for ProLiant..........................................................................................................................153
HP Smart Update Manager ..................................................................................................................................154
HPE UEFI System Utilities ........................................................................................................................154
Using UEFI System Utilities .................................................................................................................................154
Flexible boot control ..................................................................................................................................155
Restoring and customizing configuration settings .....................................................................................155
Secure Boot configuration .........................................................................................................................155
Embedded UEFI shell................................................................................................................................156
Embedded Diagnostics option...................................................................................................................156
iLO RESTful API support for UEFI ............................................................................................................156
Re-entering the server serial number and product ID ...............................................................................156
Utilities and features.............................................................................................................................................157
HPE Smart Storage Administrator.............................................................................................................157
Automatic Server Recovery.......................................................................................................................157
USB support ..............................................................................................................................................157

Contents 6
Redundant ROM support...........................................................................................................................158
Keeping the system current..................................................................................................................................159
Access to Hewlett Packard Enterprise Support Materials .........................................................................159
Updating firmware or System ROM...........................................................................................................159
Drivers .......................................................................................................................................................161
Software and firmware...............................................................................................................................161
Operating System Version Support...........................................................................................................161
Version control...........................................................................................................................................161
Operating systems and virtualization software support for ProLiant servers.............................................162
HPE Technology Service Portfolio ............................................................................................................162
Change control and proactive notification .................................................................................................162
Troubleshooting ....................................................................................................................................163
Troubleshooting resources...................................................................................................................................163
System battery......................................................................................................................................164
Warranty and regulatory information.....................................................................................................165
Warranty information ............................................................................................................................................165
Regulatory information .........................................................................................................................................165
Safety and regulatory compliance .............................................................................................................165
Belarus Kazakhstan Russia marking.........................................................................................................165
Turkey RoHS material content declaration................................................................................................166
Ukraine RoHS material content declaration ..............................................................................................166
Electrostatic discharge..........................................................................................................................167
Preventing electrostatic discharge .......................................................................................................................167
Grounding methods to prevent electrostatic discharge ........................................................................................167
Specifications........................................................................................................................................168
Environmental specifications................................................................................................................................168
Mechanical specifications.....................................................................................................................................168
Power supply specifications .................................................................................................................................169
Hot-plug power supply calculations......................................................................................................................170
Support and other resources ................................................................................................................171
Accessing Hewlett Packard Enterprise Support...................................................................................................171
Information to collect .................................................................................................................................171
Accessing updates ...............................................................................................................................................171
Websites...............................................................................................................................................................171
Customer Self Repair ...........................................................................................................................................172
Remote support....................................................................................................................................................179
Acronyms and abbreviations.................................................................................................................180
Documentation feedback ......................................................................................................................184
Index .....................................................................................................................................................185

HPE Apollo 2000 System 7
HPE Apollo 2000 System
Introduction
The HPE Apollo 2000 System consists of a chassis and nodes. There are three chassis options with
different storage configurations. The four server tray slots on the chassis must be populated with server
nodes or node blanks.
Chassis
•HPE Apollo r2200 Chassis (12 low-profile LFF model)
•HPE Apollo r2600 Chassis (24 SFF model)
•HPE Apollo r2800 Chassis (24 SFF model with storage expander backplane)
Nodes
•HPE ProLiant XL170r Gen9 Server Node (1U)
•HPE ProLiant XL190r Gen9 Server Node (2U)
The chassis supports the combination of 1U and 2U nodes. One chassis can support a maximum of the
following:
•Four 1U nodes
•Two 1U nodes and one 2U node
•Two 2U nodes
For more information about product features, specifications, options, configurations, and compatibility,
see the product QuickSpecs on the Hewlett Packard Enterprise website (http://www.hpe.com/info/qs).

Component identification 8
Component identification
Chassis front panel components
•HPE Apollo r2200 Chassis
Item Description
1
Left bezel ear
2
Low-profile LFF hot-plug drives
3
Right bezel ear
4
Chassis serial label pull tab
•HPE Apollo r2600 Chassis
Item Description
1
Left bezel ear
2
SFF HPE SmartDrives
3
Right bezel ear
4
Chassis serial label pull tab
5
Non-removable bezel blank

Component identification 9
•HPE Apollo r2800 Chassis
Item
Description
1
Left bezel ear
2
SFF HPE SmartDrives
3
Right bezel ear
4
Chassis serial label pull tab
5
Non-removable bezel blank
Chassis front panel LEDs and buttons
Item Description Status
1
Power On/Standby button and
system power LED (Node 1)1
Solid green = System on
Flashing green = Performing power on sequence
Solid amber = System in standby
Off = No power present2
2
Power On/Standby button and
system power LED (Node 2)1
Solid green = System on
Flashing green = Performing power on sequence
Solid amber = System in standby
Off = No power present2
3
Health LED (Node 2)1
Solid green = Normal
Flashing amber = System degraded
Flashing red = System critical3
4
Health LED (Node 1)1
Solid green = Normal
Flashing amber = System degraded
Flashing red = System critical3
5
Health LED (Node 3)1
Solid green = Normal
Flashing amber = System degraded
Flashing red = System critical3

Component identification 10
Item
Description
Status
6
Health LED (Node 4)1
Solid green = Normal
Flashing amber = System degraded
Flashing red = System critical3
7
Power On/Standby button and
system power LED (Node 4)1
Solid green = System on
Flashing green = Performing power on sequence
Solid amber = System in standby
Off = No power present2
8
UID button/LED1
Solid blue = Activated
Flashing blue:
•
1 flash per second = Remote management or firmware
upgrade in progress
•
4 flashes per second = iLO manual soft reboot sequence
initiated
•
8 flashes per second = iLO manual hard reboot sequence
in progress
Off = Deactivated
9
Power On/Standby button and
system power LED (Node 3)1
Solid green = System on
Flashing green = Performing power on sequence
Solid amber = System in standby
Off = No power present2
1When the LEDs described in this table flash simultaneously, a power fault has occurred. For more information, see
"Power fault LEDs (on page 15)."
2Facility power is not present, power cord is not attached, no power supplies are installed, power supply failure has
occurred, or the front I/O cable is disconnected.
3If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the system health
status.
Chassis rear panel components
•Four 1U nodes
Item
Description
1
Node 4
2
Node 3
3
RCM module (optional)
4
Power supply 2
5
Power supply 1
6
Node 2
7
Node 1

Component identification 11
•Two 2U nodes
Item
Description
1
Node 3
2
RCM module (optional)
3
Power supply 2
4
Power supply 1
5
Node 1
Chassis rear panel LEDs
Item
Description
Status
1
Power supply 2 LED
Solid green = Normal
Off = One or more of the following conditions
exists:
•
Power is unavailable
•
Power supply failed
•
Power supply is in standby mode
•
Power supply error
2
Power supply 1 LED
Solid green = Normal
Off = One or more of the following conditions
exists:
•
Power is unavailable
•
Power supply failed
•
Power supply is in standby mode
•
Power supply error

Component identification 12
Node rear panel components
•1U node rear panel components
Item
Description
1
Node serial number and iLO label pull tab
2
SUV connector
3
USB 3.0 connector
4
Dedicated iLO port (optional)
5
NIC connector 1
6
NIC connector 2
•2U node rear panel components
Item
Description
1
Node serial number and iLO label pull tab
2
SUV connector
3
USB 3.0 connector
4
Dedicated iLO port (optional)
5
NIC connector 1
6
NIC connector 2

Component identification 13
Node rear panel LEDs and buttons
•1U node
Item
Description
Status
1
Power button/LED1
Solid green = System on
Flashing green = Performing power on
sequence
Solid amber = System in standby
Off = No power present2
2
UID button/LED1
Solid blue = Activated
•
1 flash per second = Remote management
or firmware upgrade in progress
•
4 flashes per second = iLO manual soft
reboot sequence initiated
•
8 flashes per second = iLO manual hard
reboot sequence in progress
Off = Deactivated
3
Health LED1
Solid green = Normal
Flashing green = iLO rebooting
Flashing amber = System degraded
Flashing red = System critical3
4
Do not remove LED
Flashing white = Do not remove the node.
Removing the node may terminate the current
operation and cause data loss.
Off = The node can be removed.
5
iLO activity LED
Green or flashing green = Network activity
Off = No network activity
6
iLO link LED
Green = Linked to network
Off = No network connection
7
NIC link LED1
Green = Linked to network
Off = No network connection
8
NIC activity LED1
Green or flashing green = Network activity
Off = No network activity
1When the LEDs described in this table flash simultaneously, a power fault has occurred. For more information, see
"Power fault LEDs (on page 15)."

Component identification 14
2Facility power is not present, power cord is not attached, no power supplies are installed, power supply failure has
occurred, or the front I/O cable is disconnected.
3If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the system health
status.
•2U node
Item Description Status
1
Power button/LED1
Solid green = System on
Flashing green = Performing power on
sequence
Solid amber = System in standby
Off = No power present2
2
UID button/LED1
Solid blue = Activated
•
1 flash per second = Remote management
or firmware upgrade in progress
•
4 flashes per second = iLO manual soft
reboot sequence initiated
•
8 flashes per second = iLO manual hard
reboot sequence in progress
Off = Deactivated
3
Health LED1
Solid green = Normal
Flashing amber = System degraded
Flashing red = System critical3
4
Do not remove LED
Flashing white = Do not remove the node.
Removing the node may terminate the current
operation and cause data loss.
Off = The node can be removed.
5
iLO activity LED
Green or flashing green = Network activity
Off = No network activity
6
iLO link LED
Green = Linked to network
Off = No network connection
7
NIC link LED1
Green = Linked to network
Off = No network connection
8
NIC activity LED1
Green or flashing green = Network activity
Off = No network activity
1When the LEDs described in this table flash simultaneously, a power fault has occurred. For more information, see
"Power fault LEDs (on page 15)."

Component identification 15
2Facility power is not present, power cord is not attached, no power supplies are installed, power supply failure has
occurred, or the front I/O cable is disconnected.
3If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the system health
status.
Power fault LEDs
The following table provides a list of power fault LEDs, and the subsystems that are affected. Not all
power faults are used by all servers.
Subsystem
LED behavior
System board
1 flash
Processor
2 flashes
Memory
3 flashes
Riser board PCIe slots
4 flashes
FlexibleLOM
5 flashes
Removable HPE Flexible Smart Array
controller/Smart SAS HBA controller
6 flashes
System board PCIe slots
7 flashes
Power backplane or storage backplane
8 flashes
Power supply
9 flashes
System board components
NOTE: HPE ProLiant XL170r and XL190r Gen9 Server Nodes share the same system board.
Item
Description
1
Bayonet board slot
2
DIMMs for processor 2
3
DIMMs for processor 1
4
PCIe x40 riser board connector*
5
System maintenance switch
6
Mini-SAS connector 1 (SATA x4)
7
Internal USB 3.0 connector

Component identification 16
Item
Description
8
Mini-SAS connector 2 (SATA x4)
9
PCIe x24 riser board connector*
10
Dedicated iLO port connector
11
NMI header
12
PCIe x16 riser board connector*
13
microSD slot
14
System battery
15
M.2 SSD riser connector
16
TPM connector
17
Processor 1
18
Processor 2
* For more information on the riser board slots supported by the onboard PCI riser connectors, see "PCIe riser board
slot definitions (on page 26)."
System maintenance switch
Position Default Function
S1
Off
Off = iLO security is enabled.
On = iLO security is disabled.
S2
Off
Off = System configuration can be
changed.
On = System configuration is locked.
S3
Off
Reserved
S4
Off
Reserved
S5
Off
Off = Power-on password is enabled.
On = Power-on password is disabled.
S6
Off
Off = No function.
On = ROM reads system
configuration as invalid.
S7
Off
Off = Set default boot mode to UEFI.
On = Set default boot mode to legacy.
S8
—
Reserved
S9
—
Reserved
S10
—
Reserved
S11
—
Reserved
S12
—
Reserved
To access the redundant ROM, set S1, S5, and S6 to On.
When the system maintenance switch position 6 is set to the On position, the system is prepared to erase
all system configuration settings from both CMOS and NVRAM.
CAUTION: Clearing CMOS, NVRAM, or both deletes configuration information. Be sure to
configure the node properly to prevent data loss.
IMPORTANT:
Before using the S7 switch to change to Legacy BIOS Boot Mode, be sure the
HPE Dynamic Smart Array B140i Controller is disabled. Do not use the B140i controller when
the node is in Legacy BIOS Boot Mode.

Component identification 17
NMI functionality
An NMI crash dump creates a crash dump log before resetting a system which is not responding.
Crash dump log analysis is an essential part of diagnosing reliability problems, such as failures of
operating systems, device drivers, and applications. Many crashes freeze a system, and the only
available action for administrators is to restart the system. Resetting the system erases any information
which could support problem analysis, but the NMI feature preserves that information by performing a
memory dump before a system reset.
To force the system to invoke the NMI handler and generate a crash dump log, do one of the following:
•Use the iLO Virtual NMI feature.
•Short the NMI header ("System board components" on page 15).
For more information, see the Hewlett Packard Enterprise website
(http://www.hpe.com/support/NMI-CrashDump).
DIMM slot locations
DIMM slots are numbered sequentially (1 through 8) for each processor. The supported AMP modes use
the letter assignments for population guidelines.
NOTE: The arrow indicates the front of the chassis.

Component identification 18
Fan locations
Drive bay numbering
CAUTION: To prevent improper cooling and thermal damage, do not operate the chassis
unless all bays are populated with a component or a blank.
NOTE: A SATA or mini-SAS cable must be installed in a node for the node to correspond to
drives in the chassis ("SATA and Mini-SAS cable options" on page 82).
HPE Apollo r2200 Chassis drive bay numbering
One 1U node corresponds to a maximum of three low-profile LFF hot-plug drives.
•Node 1 corresponds to drive bays 1-1 through 1-3.
•Node 2 corresponds to drive bays 2-1 through 2-3.
•Node 3 corresponds to drive bays 3-1 through 3-3.
•Node 4 corresponds to drive bays 4-1 through 4-3.
One 2U node corresponds to a maximum of six low-profile LFF hot-plug drives.
•Node 1 corresponds to drive bays 1-1 through 2-3.

Component identification 19
•Node 3 corresponds to drive bays 3-1 through 4-3.
HPE Apollo r2600 Chassis drive bay numbering
One 1U node corresponds to a maximum of six SFF SmartDrives.
•Node 1 corresponds to drive bays 1-1 through 1-6.
•Node 2 corresponds to drive bays 2-1 through 2-6.
•Node 3 corresponds to drive bays 3-1 through 3-6.
•Node 4 corresponds to drive bays 4-1 through 4-6.
If a P840 Smart Array controller is installed, one 2U node corresponds to a maximum of twelve SFF
SmartDrives.
•Node 1 corresponds to drive bays 1-1 through 2-6.
•Node 3 corresponds to drive bays 3-1 through 4-6.
If using the Dynamic Smart Array B140i Controller, HPE H240 Host Bus Adapter, or HPE P440 Smart
Array Controller: one 2U node corresponds to a maximum of eight SFF SmartDrives. The remaining
drives bays must be populated with drive blanks.
•Node 1 corresponds to drive bays 1-1, 1-2, 1-4, 1-5, 2-1, 2-2, 2-3 and 2-5.

Component identification 20
•Node 3 corresponds to drive bays 3-1, 3-2, 3-3, 3-5, 4-1, 4-2, 4-4 and 4-5.
For more information on installing a storage controller, see "Controller options (on page 96)."
HPE Apollo r2800 Chassis drive bay numbering
IMPORTANT: The HPE Apollo r2800 Chassis does not support nodes using the HPE
Dynamic Smart Array B140i Controller or the HPE P840 Smart Array Controller. Hewlett
Packard Enterprise recommends installing an HPE H240 Host Bus Adapter or HPE P440
Smart Array Controller.
For information on drive bay mapping in the HPE Apollo r2800 Chassis and the factory default
configuration, see "Drive bay mapping for the HPE Apollo r2800 Chassis (on page 65)."
For more information on installing a storage controller, see "Controller options (on page 96)."