HUANUO HNCM7 User manual

(A 
Monitor Desk Mount 
Instruction Manual
Model: HNCM7
English ------------------------ 01-07 
Deutsch ------------------------ 08-14
Français ------------------------ 15-21
Español ------------------------ 22-28
Italiano ------------------------ 29-35
Thank you for choosing this HUANUO product! At HUANUO, we strive to provide you with 
the best quality products and services in the industry. Should you have any issues, please 
don't hesitate to contact us.
Technical Support: 
(US/CA)1-800-556-0533 Mon-Fri 8am - 8pm(CST)
(UK)44-808-196-3874 Mon-Fri 2pm - 10pm(UTC 
Other Info: 
[email protected]
Website: www.huanuoav.com
Manufacturer: BESTQI INNOATION (HONGKONG)TECHNOLOGY CO.,LIMITED
Address: RM21 UNIT A 11/F TIN WUI ING BLDG NO 3 HING WONG ST TUEN MUN NT HONGKONG
AMZLAB GmbH
Laubenhof 23,45326 Essen
THEMIS AR support ltd.
85 Great Portland St, London, United Kingdom.

Tools Needed (Not Included)
Phillips Screwdriver
Please carefully read all instructions before attempting installation. If you do not 
understand the instructions or have any concerns or questions, please contact 
our customer service at [email protected]. 
CAUTION: Avoid potential personal injuries and property damage! 
• Do not use this product for any purpose that is not explicitly speci ed in this 
manual. Do not exceed weight capacity. We are not liable for damage or injury 
caused by incorrect assembly or inappropriate use. 
• The desk must be capable of supporting ve times the weight of the monitor 
and mount combined.
Check the VESA Pattern of Your Monitor before the Installation
IMPORTANT SAFETY INFORMATION
If your monitor VESA is greater than 100x100 mm/4x4 in or less than 
VESA 75x75 mm/3x3 in, this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at 
[email protected] to nd a compatible mount.
MAX: 100mm/4 in
MAX: 100mm/4 in
Minimum VESA pattern: 
75mm/3 in(W)x75mm/3 in(H)
100 mm 4 in
75 mm 3 in
Supplied Parts and Hardware
 WARNING:This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use 
damaged or defective parts. lf you require replacement parts, please contact our 
customer service at [email protected]. 
• PLEASE NOTE:Not all hardware included in this package will be used.
01
3/8 in (10mm)
Socket Wrench
Drill(Optional)
7/16 in (11mm) - 
7/8 in (22mm) 
Drill(Optional)

Supplied Parts and Hardware for Step 1
02
Supplied Hardware for Step 4 and 5
1/8 in (3mm)
Small Allen Key
F3 (x1)
Nut
F4 (x2) 
Washer
M6
D (x1)
Nut
M10 
E2 (x1)
Bolt
M6X12mm
F (x1)
Bolt
M8X10mm
G (x2)
3/16 in (5mm)
Large Allen Key
F1  (x1)
5/32 in (4mm 
Medium Allen Key
F2 (x1)
Locking Plate
a (x1)
C-Clamp Brace
02 (x1)
C-Clamp
03 (x1)
Pole
01 (x1)
Bottom Pad
b (x1)
Bolt
M6X8mm
H (x2)
Supplied Parts for Step 2
Decorative Cover
c (x1)
Arm
04 (x1)
Supplied Parts and Hardware for Step 3
Faceplate
05 (x2)
Bolt
M4x12mm
A (x8)
Bolt
M4x30mm
B (x8) L13mm Spacer
C1 (x8) M4 Washer C2 (x8)

Step 1
Option A 
C-Clamp Installation
Install the Base
03
02
02
01
03
Medium
Allen Key
Large
Allen Key
F2
H
F
Medium
Allen Key
F2
b
G
F1

04
Desk
Thickness
2 3/16 in (55mm) - 3 5/32 in (80mm)
Desk
Thickness
1 3/16 in (30mm) - 2 3/16 in (55mm)
Desk
Thickness
3/8 in (10mm) - 1 3/16 in (30mm)
b
Option B: 
Grommet Installation
b
03a
03b
03b
01
03
D
a
03
D a
Tighten
D
a
D
a

05
Step 2 Secure the Arm [04] to the Pole [01] 
If there is no grommet hole on your desk, 
position the pole [01] on the mounting 
surface and mark the hole. Drill a hole 
using the drill bit in a diameter of 
7/16 in - 7/8 in (11-22mm) at the marked 
position through the mounting surface.
03b
3/4 in - 3 5/32 in
(20-80mm)
7/16 in - 7/8 in
(11-22mm)
a
E2
F1
c
Large
Allen Key
UP DeskDesk DeskDesk
Height Adjustment
04
01
WARNING
CASE If the head 
is not straight. 
Solution

06
A
Step 4 Hang the Monitor to the Arm [04]
Step 5 Adjustment
Step 3 Attach the Faceplate [05] the Back of Monitor
Use the Allen key [F3] to 
slightly adjust the height of 
each monitor.
Individual monitor height 
adjustment helps monitors to 
be perfectly aligned.
B
C1/C2
Flat back monitor Round back monitor
Small Allen Key
F3
Remove the nut [F4]
Slightly Adjust the Height of each Monitor
Phillips 
Screwdriver
Not Included
F4
F4

07
1. Slightly loosen the 
pre-assembled set screw 
[T] .
2. Tilt monitor to your 
desired angle. 
3. Re-tighten the pre-as- 
sembled set screw [T] to 
hold monitor in place. 
WARNING:
To avoid tipping, please be 
careful not to extend the 
arms too far forward or 
backward. When you adjust 
the angle of the arms, 
please make sure two arms 
are balanced to avoid 
instability of the center of 
gravity of the base.
F1
Tilt Adjustment
Large Allen Key
Tilt Adjustment
T
Swivel Swivel SwivelSwivel Swivel
Cable management
Cable Tie x 6
NOTE:
You can rotate the monitor or 
swivel the arm manually.

08
Minimales VESA Muster: 
75mm (Breite) x75mm (Höhe)
MAX:100mm
MAX:100mm
Benötigtes Werkzeug (nicht enthalten)
Kreuzschraubendreher
Bitte lesen Sie alle Anweisungen sorgfältig durch, bevor Sie instal lieren. Wenn 
Sie dieses Handbuch nicht verstehen oder Fragen haben, wenden Sie sich bitte an 
unseren Kundenservice unter [email protected]. 
Attention: évitez les potentiels dommages corporels et aux biens. 
• Ne pas utilizer ce produit dans le cas où cet instruction n’a pas indiqué. Ne pas 
dépasser le poids limité. Nous ne sommes pas responsables des dommages 
causés par le montage incorrect ou l’utilisation inappropriée. 
• La table doit être capable de supporter au moins 5 fois du poids total (les poids 
du socle, le moniteur et tous les accessoires), ne pas utiliser ce pruoduit dans un 
panneau des particules.
Überprüfen Sie vor der Installation das VESA Muster des Monitore
Wichtige Sicherheitshinweise
Wenn Ihr Monitore-VESA größer als 100 x 100 mm oder weniger als 
75x75mm ist, ist diese Installation NICHT kompatibel.
Wenn diese Halterung NICHT kompatibel ist, wenden Sie sich an den 
Kundendienst unter [email protected], um eine kompatible 
Installation zu nden.
Mitgelieferte Teile und Hardware
 WARNUNG:Dieses Produkt enthält kleine Gegenstände, die beim Verschlucken eine 
Erstickungsgefahr verursachen können. Stellen Sie vor Beginn der Montage sicher, dass alle 
Teile enthalten und nicht beschädigt sind. Verwenden Sie keine beschädigten oder defekten 
Teile. Wenn Sie Ersatzteile benötigen, wenden Sie sich bitte an unseren Kundenservice unter 
[email protected]. 
• Bitte beachten Sie: Es wird nicht alle in diesem Paket enthaltene Hardware verwendet.
10mm
SteckschlüsselBohrer(Optional) 11mm - 22mm
Bohrer(Optional)

09
Mitgelieferte Teile und Hardware für Schritt 1
Mitgelieferte Teile für Schritt 4 und 5
3mm
Kleiner Inbusschlüssel
F3 (x1)
Schraubenmutter
F4 (x2) 
Unterlegscheibe
M6
D (x1)
Schraubenmutter
M10 
E2 (x1)
Bolzen
M6X12mm
F (x1)
Bolzen
M8X10mm
G (x2)
5mm
Großer Inbusschlüsse
F1  (x1)
4mm
Mittlerer Inbusschlüssel
F2 (x1)
Verriegelungsplatte
a (x1)
C-Klemm platte
02 (x1)
C-Klemme
03 (x1)
Mast
01 (x1)
Unteres Pad
b (x1)
Bolzen
M6X8mm
H (x2)
Mitgelieferte Teile für Schritt 2
Dekorative Abdeckung
c (x1)
Arm
04 (x1)
Mitgelieferte Teile und Hardware für Schritt 3
Frontplatte
05 (x2)
Bolzen
M4x12mm
A (x8)
Bolzen
M4x30mm
B (x8)
L13mm
Abstandshalter
C1 (x8)
M4 
Unterlegscheibe
C2 (x8)