HUANUO HNDSK4 User manual

HNDSK4
(US/CA) 1-800-556-0533
(UK) 44-808-196-3874 [email protected]
www.huanuo.com
WWW.
INSTRUCTION
MANUAL
MANUEL D'UTILISATION
Rev00(B)
Desk Monitor Arm
EN Bras de Moniteur de Bureau
FR
English -------------------------------------- 02-15
Français -------------------------------------- 16-29

IMPORTANT SAFETY INFORMATION
Weight Restrictions
Check the VESA Pattern of Your Monitor Before Installation
• Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any questions or concerns, please contact our
Technical Support at 1-800-556-0533 (US/CA), 44-808-196-3874 (UK) or Customer
Service at [email protected].
CAUTION: Avoid potential injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We are not liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
• This product contains gas spring arms which are under high pressure. Do not puncture
these arms or expose the arms to fire or flame. If product is defective, please contact
our Technical Support at 1-800-556-0533 (US/CA), 44-808-196-3874 (UK) or
Customer Service at [email protected].
• Do not use this product on desks made of particle board or other soft woods.
• The information contained in this manual does not cover all possible conditions or
variables in relation to the installation of this product.
If your monitor's VESA pattern is smaller than 75mm x 75mm / 3″ x 3″ or greater than
100mm x 100mm / 3.9″ x 3.9″, this mount is NOT COMPATIBLE. Please contact our
Customer Service at [email protected] to find a compatible product.
Minimum: 75mm x 75mm / 3″ x 3″ (W x H)
Maximum: 100mm x 100mm / 3.9″ x 3.9″ (W x H)
Measure Your Monitor's VESA Pattern:
MAX: 100mm/3.9″
MAX: 100mm/3.9″
If your monitor weighs more than
the weight above, the mount is
NOT compatible. Monitor should
not exceed weight capacity.
WARNING
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only
within the weight range listed. Exceeding the
maximum weight limit may result in failure of the
mount, causing potential damage and/or injury.
It is the responsibility of the installer to verify the
total weight of the monitor and any accessories
attached.
2-10kg
(4.4-22 lbs)
02 03 04 05 06 07 08 09 10 11 12 13 14 15

Product Features
270°270°
270°270°
360°360°
180°180°360°360°
180°180°
+90°/-45°
360°
Grommet Mounting for grommet bolt
0.39-2.56″ (10-65mm)
C-Clamp Mounting for table edge
0.39-3.15″ (10-80mm)
02 03 04 05 06 07 08 09 10 11 12 13 14 15

DO NOT adjust tension without monitor attached.
1. Verify the weight of your monitor (including accessories) is within
2-10kg (4.4-22 lbs).
2. Monitor weight can be found in manual or on manufacturer's website.
3. Ensure monitor has been securely attached to the mount.
TENSION ADJUSTMENT SHOULD ONLY BE
PERFORMED AFTER MONITOR INSTALLATION
Attention
WARNING:
• Gas Spring Arm is under pressure and should be handled with care.
• Failure to follow the instructions may result in damage to the mount
and/or personal injury.
Warning!
02 03 04 05 06 07 08 09 10 11 12 13 14 15

Supplied Parts and Hardware List
5/32'' (4mm)
Allen Key
[D] × 1
M4 × 12mm
Bolt
[M-A] × 8
D4
Washer
[M-C] × 8
M4 × 30mm
Bolt
[M-B] × 8
L13mm
Spacer
[M-D] × 8
1/4'' (6mm)
Allen Key
[E] × 1
M6 x 10mm
Bolt
[A] × 2 Butterfly Nut [B] × 1
Grommet Bolt
[C] × 1
01 × 2
Compression Arm 02 × 2 Extension Arm 03 × 1 Base
04 × 2
Monitor Plate
05 × 1
Connecting Plate 06 × 1 Desk Clamp 07 × 2 Cable Management Cover
Supplied Parts and Hardware
Tools Needed (Not lncluded)
WARNING: This product contains small parts that may pose a choking hazard.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our
Technical Support at 1-800-556-0533 (US/CA), 44-808-196-3874 (UK) or Customer
Service at [email protected].
• NOTE: Not all hardware included in this package will be used.
Tape Measure Drill (Optional) 7/16''-7/8'' (11-22mm)
Drill Bit (Optional)
02 03 04 05 06 07 08 09 10 11 12 13 14 15

Option A: For Clamp Mounting
Step 1 Install the Base
Compatible desk thickness:
0.39''-3.15'' (10-80mm)
Desk
03
06
05
D
A
EE
D
A
03
A-1
A-2
02 03 04 05 06 07 08 09 10 11 12 13 14 15

Option B: For Grommet Mounting
B-2 Remove the lock plate [06a] and keep it for use in Step B-3.
03
C
Desk
Compatible desk thickness:
0.39-2.56″ (10-65mm)
Desk
06
E
06a
B-1
A-3
02 03 04 05 06 07 08 09 10 11 12 13 14 15

0.39-2″ (10-50mm)
B
C
06a
WARNING：
Ensure the bolt and nut
are securely tightened.
0.39-2.56″ (10-65mm)
NOTE: If a hole is needed for grommet installation, be
sure to leave at least 2″ (50mm) from the edge of
desktop and mark where the hole will be drilled. Use
either a 7/16-7/8″ (11-22mm) drill bit for this step.
7/16-7/8″ (11-22mm)
2″ (50mm)
03
B-3
Drill
(Not Included)
7/16-7/8″
(11-22mm)
Drill Bit
(Not Included)
02 03 04 05 06 07 08 09 10 11 12 13 14 15

Step 2 Secure the Arms to the Base
02
01
2-1 Push the extension arms [02] into the base, and then tighten the set screws on the
arm joints.
2-2 Slide the compression arms [01] onto the extension arms [02], and then tighten the
set screws.
D
Desk
Desk
D
02
NOTE: The cable management
cover face down.
02
01
01
02
02 03 04 05 06 07 08 09 10 11 12 13 14 15

3-2 Attach the Monitor Plates to Your Monitors
Step 3 Attach the Monitor Plates to the Monitors
Option B：For Curved Monitor
Hand thread bolts into the threaded inserts on the back of your monitor to determine which bolt
(M4 x 12mm or M4 x 30mm ) to use. A minimum of 4-5 turns into the threading is required. Do not
turn past the bottom of the hole.
M4 x 12mm
M4 x 30mm
3-1 Select Monitor Bolts
Option A：For Flat Back Monitor
E
E
M-B
M-C
M-D
M-A
M-C
The hanging tab is
directed toward the
top of monitor.
The hanging tab is
directed toward the
top of monitor.
D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
D
O
N
O
T
o
v
e
r
t
i
g
h
t
e
n
02 03 04 05 06 07 08 09 10 11 12 13 14 15