HUANUO HNCM7 User manual

V7.1
Monitor Desk Mount
Instruction Manual
Model: HNCM7
Thank you for choosing this HUANUO product! At HUANUO
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.huanuoav.com/reviews if you
are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
[email protected](DE/UK/FR/IT/ES/NL/SE/AU)
Website:
www.huanuoav.com
English ------------------------ 01-07
Deutsch ------------------------ 08-14
Français ------------------------ 15-21
Español ------------------------ 22-28
Italiano ------------------------ 29-35

Tools Needed (Not Included)
Phillips Screwdriver
Please carefully read all instructions before attempting installation.
If you do not understand the instructions or have any concerns or
questions, please contact our customer service at
[email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly
specified in this manual. Do not exceed weight capacity. We are not
liable for damage or injury caused by incorrect assembly or
inappropriate use.
• The desk must be capable of supporting five times the weight of
the monitor and mount combined.
Check the VESA Pattern of Your Monitor before the Installation
IMPORTANT SAFETY INFORMATION
If your monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3 in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
MAX:100mm/4 in.
MAX:100mm/4 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
100 mm ≈ 4 in.
75 mm ≈ 3 in.
01
3/8 in.(10mm)
Socket Wrench
Drill(Optional)
7/16 in.(11mm) -
55/64 in.(22mm)
Drill(Optional)

Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our
customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Supplied Parts for Step 2
Decorative Cover
c (x1)
Arm
04 (x1)
02
Washer
M10
D (x1)
Washer
M6
d (x1)
Nut
M10
E (x1)
Bolt
M6X12MM
F(x1)
Bolt
M8X10MM
G (x2)
13/64in.(5mm)
Large Allen Key
F1
(x1)
5/32in.(4mm）
Medium Allen Key
F2 (x1)
Locking Plate
a (x1)
C-Clamp Brace
02 (x1)
C-Clamp
03 (x1)
Pole
01 (x1)
Bottom Pad
b (x1)
Bolt
M6X8MM
H (x2)

Step 1
Option A：
C-Clamp Installation
Spacer
L5mm
C (x8)
Supplied Parts and Hardware for Step 3
Supplied Hardware for Step 4 and 5
Faceplate
05 (x2)
Install the Base
02
01
03
Medium
Allen Key
F2
H
F
Bolt
M4X12MM
A(x8)
Bolt
M4X16MM
B(x8)
1/8in.(3mm)
Small Allen Key
F3(x1)
Nut
F4(x2)
Medium
Allen Key
F2
b

03
02
04
Large
Allen Key
G
F1
DeskDesk DeskDesk
Tighten
Desk
Thickness
2 11/64 in.(55mm) - 3 5/32 in.(80mm)
Desk
Thickness
1 3/16 in.(30mm) - 2 11/64 in.(55mm)
Desk
Thickness
3/8 in.(10mm) - 1 3/16 in.(30mm)
da
03

05
Step 2 Secure the Arm [04] to the Pole [01]
b
Option B:
Grommet Installation
b
03a 03b
03b
If there is no grommet hole on your desk,
position the pole [01] on the mounting
surface and mark the hole. Drill a hole
using the drill bit in a diameter of
7/16 in. - 55/64 in. (11-22mm) at the
marked position through the mounting
surface.
a
03b
25/32 in. - 3 5/32 in.
(20-80mm)
7/16 in. - 55/64 in.
(11-22mm)
F1
c
Large
Allen Key
UP DeskDesk DeskDesk
Height Adjustment
04
01
01
D
E

06
A
Step 4 Hang the Monitor to the Arm [04]
Step 5 Adjustment
Step 3 Attach the Faceplate [05] the Back of Monitor
Use the Allen key [F3] to
slightly adjust the height of
each monitor.
Individual monitor height
adjustment helps monitors to
be perfectly aligned.
B
C
Flat back monitor Round back monitor
Small Allen Key
F3
Remove the nut [F4]
Slightly Adjust the Height of each Monitor
Phillips
Screwdriver
Not Included
F4
F4

07
1. Slightly loosen the
pre-assembled set screw
[T] .
2. Tilt monitor to your
desired angle.
3. Re-tighten the pre-as-
sembled set screw [T] to
hold monitor in place.
Warning:
To avoid tipping, please be
careful not to extend the
arms too far forward or
backward. When you adjust
the angle of the arms,
please make sure two arms
are balanced to avoid
instability of the center of
gravity of the base.
Swivel Swivel Swivel
F1
Tilt Adjustment
Large Allen Key
Swivel Swivel
Tilt Adjustment
Cable management
Cable Tie x 6
Note:
You can rotate the monitor or
swivel the arm manually.
T