HUANUO HNDS8 User manual

Check the VESA Pattern of Your Monitor beforeYouBegin the Installation
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
customer service at [email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also it
is strictly prohibited to dismantle without professionals. Please return to the manufacturer
or hand over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the
mount, the monitor and all accessories weight). Don't use the product on particle board.
IMPORTANT SAFETY INFORMATION
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your Monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
01
Weight Restrictions
4.4-19.8 lbs.
(2-9 kg)
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
If your monitor weighs more, this mount is NOT
compatible.
Your monitor (including
accessories) CANNOT EXCEED
4.4-19.8lbs (2-9 kg)
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
100 mm ≈ 4 in.
75 mm ≈ 3 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)

02
Product Features
C-Clamp Mounting
Grommet Mounting

03
Warning!
Do not adjust tension without monitor.
1. Ensuremonitorhas been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensurethe net weight of monitor (including accessories) is between
4.4~19.8 Ibs (2-9 kg).
Clockwise to reduce
tension(carry less weight)
Counter-clockwise to increase
tension(carry more weight)
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION
Adjustment Sign

04
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware
Warning:This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, contact our
customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
5/32 in.(4mm)
Allen Key
(F)
(D) M8
Butterfly Nut
(D) M8x120mm
Grommet Bolt
(E)
Locking Plate
03 Pole Assembly X1
02 C-Clamp X1
Tools Needed (Not lncluded)
Screwdriver
M6x12mm (3pcs)
Bolt(C)

05
5/32 in.(4mm)
Allen Key
(F)
13/64 in.(5mm)
Allen Key
(F)
04 Cable Cover X2 M4x6mm (4pcs)
Bolt (G)
01 Arm X2 05 Cable Clip X2
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Supplied Hardware for Step 4 and Step 6
Supplied Parts and Hardware for Step 8
Bolt (A)
M4x12mm (8pcs) Bolt (B-1)
M4x16mm (8pcs)
Spacer (B-2)
5mm (8pcs)

06
Secure the base to the desktop
4
Step 1 Install the Base
A. For Clamp Mounting A-1 Install the C-Clamp
3Connect part [Y] to part [X] according to the thickness of the desktop
OR
The first choice
X
Y
The second choice
X
Y
1
2
Warning:
Ensure bolts are
secured firmly.
5/32 in.
(4mm)
03
X
F
Connect part [X] to pole
assembly [03]
Detach the c-clamp entirely
X
Y
①
②

07
B. For Grommet Mounting
1Install the grommet bolt
Warning:
Ensure bolts are
secured firmly.
D
Warning:
Ensure bolts are
secured firmly.
Secure the base to desktop using locking plate [E] and butterfly nut [D]
2
E
D
φ0.4-φ2 in.
(φ10-φ50mm)

08
Step 2 Install the Arms
Ensure bolts are
secured firmly.
05
03
Slide arm [01] to the pole assembly [03]
2
1Slide the cable clip [05] to the pole assembly [03]
Secure the arm [01] to the
pole assembly [03] by
tightening the preassemble
bolts on the arms [01]
3
01
03
5/32 in.
(4mm)

09
Step 4 Adjust Gas Spring Tension
Be sure to keep the arm in
horizontal position during
adjustment. Or else, it will be
difficult to adjust the mount or
possibly damage the mount.
1. If the monitor can stay at the desired height
by itself, no adjustment needed.
2. If the monitor rises up, press the arm to keep
it in horizontal position and then use the
13/64 in.(5mm) Alley key (F) to turn the bolts
clockwise(“-” direction) to reduce tension of
the arm only until the monitor can stay at the
desired height by itself.
3. If the monitor falls down, lift the arm to keep
it in horizontal position and then use the
13/64 in.(5mm) Alley key (F) to turn the bolts
counter-clock-wise(“+” direction) to increase
tension of the arm only until the monitor can
stay at the desired height by itself.
Step 3 Attach Monitors to the Arms
3-1 Choose Proper bolts 3-2 Install Monitors to the Arms
10.1-0.2in.(3-5mm) spacing left
The tension is preset at
8.8~11 Ibs(4-5kg). After
hanging the monitor to the
mount,please release the
monitor slowly to prevent it
from falling suddenly.
100x100mm
75x75mm
A
Screwdriver
[Not Included]
Flat back monitor
Round back monitor
100x100mm
75x75mm
B-1
B-2