HUANUO HNSS12 User manual

Thank you for choosing this HUANUO product! At HUANUO we strive
to provide you with the best quality products and services in the
industry. Please share your experience of our product with others at
www.huanuoav.com/reviews if you are satisfied. Should you have any
issues, please don't hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
[email protected] (DE/UK/FR/IT/ES/AU)
[email protected] (JP)
Website:
www.huanuoav.com
Monitor Desk Mount
Instruction Manual V4.0
Model: HNSS12
English ------------------------ 01-10
Deutsch ------------------------ 11-19
Français ------------------------ 20-28
Español ------------------------ 29-37
Italiano ------------------------ 38-46
日本語 ------------------------ 47-55

Check the VESA Pattern of Your Monitor beforeYouBegin the Installation
IMPORTANT SAFETY INFORMATION
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your Monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
Weight Restrictions
4.4-26.5 lbs.
(2-12 kg)
If your monitor weighs
more, this mount is
NOT compatible.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
100 mm ≈ 4 in.
75 mm ≈ 3 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
Technical Support line at 1-800-556-0533 or customer service at
[email protected]
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and per
is strictly prohibited to dismantle without professionals. Please return to the manufacturer
or hand over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the
mount, the monitor and all accessories weight). Don't use the product on particle board.
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

Product Features
Grommet Mounting
25/32 in. ~ 35/32in.
(20~80mm)
C-Clamp Mounting
25/32 in. ~ 35/32in.
(20~80mm)
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

Warning!
Do not adjust tension without monitor.
1. Ensure monitor has been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensure the net weight of monitor (including accessories) is between
4.4~26.5 Ibs (2-12 kg).
Clockwise to reduce
tension(carry less weight)
Counter-clockwise to increase
tension(carry more weight)
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION
Adjustment Sign
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

5/32 in.(4mm)
Medium Allen Key
E (x1)
13/64 in.(5mm)
Large Allen Key
E (x1)
Bolt
M6x12mm
C (x4)
Bolt
M8x38mm
G (x1)
φ16xφ8.2x1.5mm
Washer
G (x1)
03 x1
Base
1/8 in.(3mm)
Small Allen Key
E (x1)
02 x1
Arm Extension
01 x1
Arm
06 x1
Monitor Plate
Locking Plate
F (x1)
05 x1
C-Clamp
Bolt
M4x12mm
A (x4)
Bolt
M4x16mm
B-1 (x4)
5mm Spacer
B-2 (x4)
07 x1
Cable
Pressure Plate
H (x1)
Grommet Bolt
D (x1)
Butterfly Nut
D (x1)
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Warning:This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, contact our
customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Supplied Parts and Hardware for Step 4
Phillips Screwdriver
Electric Drill
(Optional)
Drill Bit
(Optional)
0.4 in.(10mm) - 2 in.(50mm)
Y
X
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

1. Install the Base
Warning:
Ensure bolts are
secured firmly.
A. For Clamp Mounting
E
Medium
Allen Key
X
Y
X
YOR OR
04 x1
Decorative Cover
13/64 in.(5mm)
Large Allen Key
E (x1)
Supplied Hardware for Step 5 and Step 7
Supplied Part for Step 8
E
Medium
Allen Key
Y
07 USB
03
C
E
Medium
Allen Key
Y
07 USB
03
C
X
Y
X
Y
Lift the part [X] to
detach it from part [Y]
YXE
Medium
Allen Key
Y
X
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

Warning:
Ensure bolts are
secured firmly.
B. For Grommet Mounting
1 2
2
1 2
1
D
D
F
E
Medium
Allen Key
07 USB
03
H
C
25/32 in. ~ 3 5/32in. (20~80mm)
25/32 in. ~ 3 5/32in. (20~80mm)
If there is no grommet hole on your desk, position the base [03] on the mounting
surface and mark the hole. Drill a hole using the drill bit in a diameter of 0.4 in.(10mm) -
2 in.(50mm) at the marked position through the mounting surface.
Ensure butterfly nut is
secured firmly.
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

2. Install the Arm and Arm Extension to Base
3. Install the Monitor Plate to Arm
Attach the monitor plate [06] from the sides
of the top end of arm [01], then secure the
monitor plate using bolt and washer [G]
Large
Allen Key
E
G
06
01
1
2
Small Allen Key
Small
Allen Key
E
E
01
02
02
03
Do not over-tighten the set
screw [M] in order not to
affect the rotation of the arm.
M
M
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

5. Adjust Gas Spring Tension
75 mm ≈ 3 in.
100 mm ≈ 4 in.
Be sure to keep the arm in
horizontal position during
adjustment. Or else, it would
be difficult to adjust the
mount or damage the mount.
1. If the monitor can stay at the desired height
by itself, no adjustment needed.
2. If the monitor rises up, press the arm to keep
it in horizontal position and then use the Large
Allen Key (E) to turn the bolt
clockwise(“-” direction) to reduce tension of
the arm only until the monitor can stay at the
desired height by itself.
3. If the monitor falls down, lift the arm to keep
it in horizontal position and then use the Large
Allen Key (E) to turn the bolt
counter-clockwise(“+” direction) to increase
tension of the arm only until the monitor can
stay at the desired height by itself.
4-1 Choose Proper Bolts 4-2 Install Monitors to the Arms
10.1-0.2in.(3-5mm) spacing left
A
100x100mm
75x75mm75x75mm
100x100mm
Phillips
Screwdriver
[Not Included]
Flat back monitor
Curved back monitor
4. Attach Monitors to the Arm
B-1
B-2
100x100mm
75x75mm75x75mm
100x100mm
The tension is preset at
8.8-11 LBS(4-5kg). After
hanging the monitor to
the mount, please release
the monitor slowly to
prevent it from falling
suddenly.
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

6. Rotation Restriction
Non-proper usage directions Proper usage directions
4. Route Cables along the Arm
7. Tilt Adjustment
Adjust monitor to proper tilt angle. Use Allen key (E) to tighten the bolt and fix tilt angle
Large Allen Key
E
Large Allen Key
E
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55

8. Route Cables along the Arms
9. Attach the Decorative Cover to C-Clamp
Warm Tips: The decorative cover [04] can only be used for the C-Clamp.
2
5
Pinch the both sides of the top end of
the cover to make it attach to the arm
6
4
Pull down the groove part
along the arm to detach the
cover from the arm
02
b
1
01
3
04
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28
29 30 31 32 33 34 35 36 37
38 39 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55