HUANUO HNHM5 User manual

Model: HNHM5
3
Monitor Table Stand
Instruction Manual
Thank you for choosing this HUANUO product! At HUANUO
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.huanuoav.com/reviews if you
are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.huanuoav.com

•Carefully open the carton, remove contents and lay out on cardboard or other protec-
tive surface to avoid damage.
•Check package contents against the Supplied Parts and Hardware Lists to assure that
all components were received undamaged. Do not use damaged or defective parts.
•Not all parts and hardware included will be used. lf you require replacement parts,
contact customer service at [email protected]
•Carefully read all instructions before attempting installation.
•If you do not understand the instructions or have any concerns or questions, please
contact customer service at [email protected]
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaim any liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
UNPACKING INSTRUCTIONS AND IMPORTANT SAFETY INFORMATION
Supplied Parts and Hardware
X1
M4x12mm
M-A X8 M4X30mm M-B X8 D4
M-C X8
M-D X8
1
01 X1
04
X2
05 X2 06 X2 07 X1 08 X1 09
X1
02 X1 03
1/8 in.(3mm)
D x1
15/64 in.(6mm)
E x1
M8x10mm
A x2 M5x16mm B x3 C x2

Tighten the screw [S] using Allen key [E] to fix the two poles STEP 1-3
Install part [03] to pole[02]
STEP 2A-1
2
Step 2A
01
02
B
D
D(3mm)
03
For C Clamp Mounting
01
Step 1 Connect Upper Pole to Lower Pole
S
S
Loosen the screw [S] on pole [02] using Allen key [E]
Connect pole [01] to pole [02]
02
02
02
STEP 1-1
STEP 1-2
1/8 in.(3mm)

09 a
E15/64 in.(6mm)
Remove part [a]
from part [04]
STEP 2B-2 STEP 2B-3
Adjust the mount according to the thickness of desktopSTEP 2A-2
Install part [04] to part [03]STEP 2A-3
Secure the mount to the desktopSTEP 2A-4
Install part [08] to pole [02]STEP 2B-1
Step 2B
3
A
B
D
E
04
02
04
03
08
For Grommet Mounting
a
Secure the mount
to the desktop
1/8 in.(3mm)
15/64 in.(6mm)
＜45mm
(1 in.)
45mm(1 in.)
-
80mm(3 in.)

STEP 3-1 STEP 3-2
4
Step 3
Check Monitor Hole Pattern and Select TV Monitor Bolts
Step 4
MAX:100 mm
MAX:100
mm
Only one bolt size fits your monitor.
100 mm ≈ 7 7/8 in.
75 mm ≈ 4 in.
05
07
E
Install Cable Clip & Monitor Connector to the Pole Assembly
Slide the cable clip [07] and monitor
connector [05] in sequence to the pole
assemble as shown below
Secure the monitor connectors
[05] to the pole assembly
15/64 in.(6mm)
M4x12mm M4x30mm

5
Attach the Monitor Brackets to the Monitors
Step 5
Hang Monitors to the Stand and Secure with Nuts [C]
Step 6
Bolt length:Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the monitor.
-Too long will damage the monitor.
M-A
M-C
06
M-B
M-C
M-D
FLAT BACK MONITOR
(UNIVERSAL MONITOR PLATE)
ROUND BACK MONITOR
(UNIVERSAL MONITOR PLATE)
C

6
Store Allen Keys into the Cable Clip
Step 9
Fix Tilt Angle of the Monitors
Step 7
Manage Cables
Step 8
E 15/64 in.(6mm)
D 1/8 in.(3mm)
E15/64 in.(6mm)

7
Features
180°
360°
360°
Tilt
Tilt
Warning: To avoid tipping, please be careful not to extend the monitor too far back-
ward.When you adjust the angle of the monitor, please make sure the monitor is
balanced to avoid instability of the center of gravity of the base.