Huawei Backup Box-B0 User manual

Backup Box-(B0, B1)
Quick Guide
Issue: 01
Date: 2021-01-10

1
1Overview
3. Only certified electricians are allowed to operate the device. Operation personnel must wear
proper personal protective equipment (PPE).
1. The information in this document is subject to change without notice. Every effort has been
made in the preparation of this document to ensure accuracy of the contents, but all
statements, information, and recommendations in this document do not constitute a
warranty of any kind, express or implied.
2. Before installing the device, read the user manual carefully to get familiar with product
information and safety precautions.
4. Before installing the device, check that the package contents are intact and complete against
the packing list. If any item is missing or damaged, contact your dealer.
5. The device damage caused by the violation of instructions in this document is not covered
under warranty.
6. The cable colors involved in this document are for reference only. Select cables in accordance
with local cable specifications.
Function
The Backup Box is used in a residential rooftop PV plant system to control the inverter grid-tied
or off-grid state. When the grid fails, the inverter switches to the off-grid state and supplies
power to off-grid loads in backup mode. When the grid recovers, the inverter switches back to
the grid-tied state.
Model Number
No.
Meaning
Value
1
Product name
Backup Box: Backup Box
2
Design code
B0: single
-phase
B1: three
-phase
System Networking
The grid-tied system of a rooftop PV plant consists of PV strings, an energy storage system (ESS),
an inverter, a Backup Box, a management system, an AC switch, and a power distribution unit.

2
Appearance
(1) Front panel
(2) Lock
(3) Hanging kit
(4) Off
-grid load port (BACKUP LOAD)
(5) Grid AC port (GRID)
(6) Inverter AC port (INVERTER AC)
(7) COM port (COM)
(8) Ventilation valve
(9) Ground point
Supported Grid Types
The Backup Box supports the following grid types: TN-S, TN-C-S and TT. When the inverter is in
three-phase, three-wire mode, the Backup Box does not support off-grid operation.

3
3
Installation Space Angle
1. When a Backup Box is installed outdoors, avoid direct sunlight. You are advised to install it in
a sheltered place or install an awning over it.
2. A surge protective device (SPD) needs to be installed on the grid side of the Backup Box.
Installation Requirements
2.1
2Device Installation
(10) Off
-grid load switch
Mounting Holes and Dimensions
When drilling holes, avoid the water pipes and power cables buried in the wall.

4
Installing a Backup Box
2.2
M6x60 expansion bolts are delivered with the Backup Box. If the length and number of the
bolts do not meet installation requirements, prepare M6 stainless steel expansion bolts by
yourself.
The expansion bolts delivered with the inverter are mainly used for solid concrete walls. For
other types of walls, prepare bolts by yourself and ensure that the wall meets the load
bearing requirements of the inverter.
In residential areas, do not install the inverter on drywalls or walls made of similar
materials which have a weak sound insulation performance because the noise generated by
the inverter is noticeable.
Level

5
Preparations
3.1
Connect cables in accordance with local installation laws and regulations.
Before connecting cables, ensure that the circuit breaker on the Backup Box and all the
switches connecting to the Backup Box are set to OFF position. Otherwise, the high voltage
of the Backup Box may result in electric shocks.
3Electrical Connection
No.
Cable
Type
Conductor Cross
-
Sectional Area Range
Outer Diameter
1
PE cable
Single
-
core outdoor copper
cable
4
–10 mm2
N/A
2
Off
-grid load
output power cable
Outdoor copper cable
4
–6 mm2
10
–21 mm
3
Grid AC output
power cable
Outdoor copper cable
4
–6 mm2
10
–21 mm
4
Inverter AC input
power cable
Outdoor copper cable
4
–6 mm2
10
–21 mm
5
Signal cable
Two
-core outdoor shielded
twisted pair cable
0.20
–1 mm2
4
–8 mm
Prepare cables based on site requirements.
Installing a PE Cable
3.2
Do not connect the neutral wire to the enclosure as a PE cable. Otherwise, electric shocks
may occur.
Ground point

6
Installing an Output Power Cable for Off-Grid Loads
3.3
Installing a Grid AC Output Power Cable
3.4
X1
Before installing a cable, open the panel of the Backup Box, route the cable through the off-grid
load port, and connect the cable. After all cables are connected, reinstall the panel.
Off-Grid Load Terminal (X1)
No.
.
1
2
3
4
Single-
Phase
L
N
-
PE
Off-Grid Load Terminal (X1)
No.
.
1
2
3
4
Three
-
Phase
L
N
-
PE
Connecting Grid AC Terminals（X2）
No.
1
2
3
4
5
6
7
Single
-Phase
L
-
-
N
-
PE
-

7
If multiple inverters are connected in parallel, the connection of AC power cables L1, L2, and L3
on the power grid side of the Backup Boxes connected to each inverter must be the same.
Installing an Inverter AC Input Power Cable
3.5
X2
Connecting Grid AC Terminals（X2）
No.
1
2
3
4
5
6
7
Three
-Phase
L1
L2
L3
N
-
PE
-
Connecting AC Input Terminals of the Inverter（X3）
No.
1
2
3
4
5
6
7
8
9
10
11
Single
-Phase
-
L
-
-
-
N
-
-
-
PE
-
Connecting AC Input Terminals of the Inverter（X3）
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
Three
-Phase
L1
-
L2
-
L3
-
-
N
-
-
-
PE
-

8
Installing a Short-Circuiting Plate
3.6
The sequence of connecting the cables to a single-phase Backup Box and to the AC terminals L,
N, and PE on the inverter must be the same. The sequence of connecting the cables to a three-
phase Backup Box and to the AC terminals L1, L2, and L3 on the inverter must be the same.
Otherwise, the device cannot work properly. (As shown in the following figures, connect the
cables to a single-phase Backup Box in the sequence of L, N, and PE from left to right, and
connect the cables to a three-phase Backup Box in the sequence of L1, L2, and L3.)
Backup Box-side terminal (single-phase) Inverter-side terminal (single-phase)
X3
Backup Box-side terminal (three-phase) Inverter-side terminal (three-phase)

9
No.
Label
Definition
Note
1
DI
Digital input signal+
Connects to the positive pole of the DI port and functions as
the port for the Backup Box to send feedback signals.
2
GND
GND
of the DI port
Connects to the
GND of the DI port.
Communications Terminal Definition
Installing Signal Cables
3.7
Neutral Wire Disconnected
If the neutral wire needs to be disconnected in off-grid mode (such as in German), according to
the local power grid standard, insert the short-circuiting plate between 10 and 11 of the AC
terminal X3 for the single-phase Backup Box. Insert the short-circuiting plate between 12 and
13 of the AC terminal X3 for the three-phase Backup Box.
Power grid AC terminal X2
(Single-Phase/Three-Phase)
Inverter AC terminal X3 (single-phase) Inverter AC terminal X3 (three-phase)
Neutral Wire Connected
If the neutral wire cannot be disconnected from the power grid in off-grid mode (such as in
Australia), insert the short-circuiting plate between 4 and 5 of the AC terminal X2 according to
the local power grid standard.
•When installing a short-circuiting plate, ensure that it is inserted into the correct port and
securely installed to avoid short circuits caused by incorrect installation.
•If no short-circuiting plate is installed, the neutral wire will be suspended in off-grid mode,
but the off-grid/grid-tied switching function is not affected. You are advised to install a
short-circuiting plate according to the local power grid standard.

10
Inverter AC
COM port (COM)
COM Port Pin Definitions
No.
Label
Definition
Description
5
GND
GND
Connects to the
GND of the DI2 port.
8
DI2
Digital
input
signal 2+
Connects to the positive terminal of DI2
and functions as the port for the Backup
Box to send feedback signals.
3.8 Connecting Signal Cables on the Inverter Side
SUN2000-(2KTL-6KTL)-L1
X4

11
SUN2000-(3KTL-12KTL)-M1
COM port (COM)
No.
Label
Definition
Note
8
DIN1
Digital input
signal 1+
Functions as the port for the
Backup Box to send feedback
signals.
16
GND
GND
Connects to the
GND
of DIN1.
COM Port Pin Definitions
Inverter AC
4Verifying the Installation
No.
Acceptance Criteria
1
The installation is correct and reliable.
2
Cables are routed properly as required by the customer.
3
Cable ties are secured evenly and no burr exists.
4
The PE cable is connected correctly, securely, and reliably.
5
The switch of the Backup Box and all the switches connected to it are OFF.
6
Cables are connected correctly and securely. Use a phase sequence meter to check
whether the cables on the grid side are connected correctly.
7
Unused terminals and ports are locked by watertight caps.
8
The installation space is proper, and the installation environment is clean and tidy.
5Powering On the System
1. Use a multimeter to check whether the AC voltage in the power distribution box (PDB) is
within the allowed range and whether cables are correctly connected.
2. Turn on the PDB AC switch between the Backup Box and the power grid. (Ensure that the
load switch of the Backup Box is OFF.)
3. Check whether the cable connection of the grid AC terminals is correct.
4. (Optional) Remove the locking screw beside the DC switch on the inverter.

12
5. Turn on the DC switch (if any) between the PV strings and the inverter.
6. Turn on the DC switch at the bottom of the inverter.
7. Check that the off-grid load power does not exceed the off-grid output power allowed by
the inverter.
8. After ensuring that the load circuit is normal, turn on the AC switch of the Backup Box.
9. Observe the LED indicators on the front of the inverter to check the running status of the
inverter.
Parameter Settings
Open the FusionSolar app, log in to intl.fusionsolar.huawei.com using the installer account,
choose My > Device Commissioning, and connect to the WLAN hotspot of the solar inverter.
On the home page, choose Setting > Feature parameters to set the off-grid/grid-tied control
parameters.
6System Commissioning
Download and install the latest version of the FusionSolar app by referring
to the quick guide for the corresponding inverter model or the FusionSolar
App Quick Guide . Register an installer account and create a plant and
owner (skip this step if an account has been created). You can scan the QR
code to obtain the FusionSolar App Quick Guide .
During system deployment, the AC power supply needs to be connected to ensure that the off-
grid/grid-tied switching function of the Backup Box can be verified.
Category
Status (Blinking Slowly, On for 1s and then Off
for 1s)
Definition
Running
indication
N/A
Steady green
Steady green
On
-grid
Steady orange
Steady orange
Backup
Blinking orange slowly
Off
Standby in backup mode
Blinking orange slowly
Blinking orange slowly
Overload in backup mode
If the off-grid load is overloaded, indicators and on the inverter blink orange slowly.
Reduce the off-grid load power and manually clear the alarm or until the inverter is recovered.
If the inverter is standby in off-grid mode, check the inverter alarms and rectify the fault.

13
8Troubleshooting
7Routine Maintenance
To ensure the long-term and proper running of the system, you are advised to perform routine
maintenance on the Backup Box periodically.
1. Check the system cleanliness, system running status, electrical connection, and grounding
reliability every half year.
2. Check whether the off-grid/grid-tied switching function is normal each quarter.
1. Backup Box checking solution:
After arriving at the site, the personnel can check whether the Backup Box is damaged as
follows:
a. It is recommended that loads be disconnected before checking.
b. Use a multimeter to check the connectivity between the Backup Box terminals, as shown in
the following tables.
Parameter
Settings
Value
Off
-grid mode
If this parameter is enabled, the Backup Box switches to the
off
-
grid mode when the grid fails. This parameter can be set
only when the Backup Box is configured. If the Backup Box is
not configured, this parameter cannot be enabled.
Otherwise, an alarm is generated.
Enable
Disabled
(default)
Backup power
SOC
Sets the backup power SOC. In grid
-tied mode, the battery
does not discharge when it is discharged to the backup
power SOC. When the grid fails, the battery supplies power
to loads in off
-grid mode until it reaches the end-of-
discharge capacity.
[20%, 100%]
Default value: N/A
Grid
-tied/Off-
grid mode
switching
If this parameter is set to Automatic switching, the system
switches to the off
-grid mode when the grid fails, and
switches to the grid
-tied mode when the grid recovers.
If this parameter is set to Manual switching, you need to log
in to the app and connect the inverter to enable the off
-
grid
mode when the grid fails.
Automatic
switching
(default)

Manual switching
1. Power on the Backup Box according to the power-on procedure, wait for the inverter to
connect to the power grid, and log in to the app to enable Off-grid mode.
2. Turn off the AC switch in the PDB between the Backup Box and the power grid, and check
whether the off-grid output is normal. The inverter indicators and are steady
orange. (If the AC switch between the inverter and the Backup Box is turned off, the off-grid
switching is not triggered and the inverter is in off-grid standby mode.)
3. Turn on the AC switch in the PDB between the Backup Box and the power grid. The inverter
indicators and blink green slowly until the inverter is connected to the power grid.
Verifying the Off-grid/Grid-tied Switching Function

14
9Product Specifications
c. If the conduction status of an item is inconsistent with that in the tables, the Backup Box is
damaged.
No.
Wiring Requirements
Detection Terminal
Circuit
Breake
r (QF)
Grid
Inverter
X4
-1 & X4-2
COM
-1 &
COM
-2
X2
-1 & X3-1
GRID
-L1 &
INVERTER
-L1
X3
-3 & X3-8
INVERTER
-L2
& INVERTER-N
X2
-1 & X1-1
GRID
-L1 &
LOAD
-L
X3
-3 & X1-2
INVERTER
-L2
& LOAD-N
1
On
Power
off
Shutdown
Connected
Disconnected
Disconnected
Disconnected
Disconnected
2
On
Power
on
Shutdown
Disconnected
Connected
Disconnected
Connected
Disconnected
3
On
Power
off
Off
-grid
output
Connected
Disconnected
Connected
Disconnected
Connected
Three-Phase Backup Box
2. If the mains recovers but the inverter still works in off-grid state (LED1 and LED2 are steady
orange), contact the customer service personnel or dealer for repair.
3. If the off-grid mode is enabled when no Backup Box is connected, an alarm indicating that
the Backup Box is abnormal is reported when the AC power supply is disconnected. In this
case, the fault cannot be rectified. The fault is rectified only after the inverter and battery are
powered off.
4. If the Backup Box is used for the first time and is not used later, you must disable the off-
grid mode when the inverter is running properly. Otherwise, you need to power on the
inverter again and modify the settings.
5. If the single-phase Backup Box generates abnormal noises during repeated switching, check
whether the inverter AC terminal is reversely connected to the power grid AC terminal.
N
o
.
Wiring Requirements
Detection Terminal
Circuit
Breaker
(
QF)
Grid
Inverter
X4
-1 & X4-2
COM
-1 &
COM
-2
X2
-1 & X3-2
GRID
-L &
INVERTER
-L
X3
-6 & X3-10
INVERTER
-N
&
INVERTER
-PE
X2
-1 & X1-1
GRID
-L &
LOAD
-L
X3
-6 & X1
-
2
INVERTER-
N
& LOAD-
N
1
On
Power
off
Shutdown
Connected
Disconnected
Disconnected
Disconnected
Connected
2
On
Power
on
Shutdown
Disconnected
Connected
Disconnected
Connected
Connected
3
On
Power
off
Off
-grid
output
Connected
Disconnected
Connected
Disconnected
Connected
Single-Phase Backup Box

15
9Customer Service Contact Information
Customer Service Contact
Region
Country
Service Support Email
Phone
Europe
France
[e-mail]
0080033888888
Germany
Spain
Italy
UK
Netherlands
Other countries
For details, see
solar.huawei.com.
Asia Pacific
Australia
[e-mail]
1800046639
Turkey
[e-mail]
N/A
Malaysia
[e-mail]
0080021686868
/1800220036
Thailand
([phone] (charged
by local call)
1800290055 (free in
Thailand)
China
[e-mail]
400
-822-9999
Other countries
[e-mail]
0060
-3-21686868
Japan
Japan
[e-mail]
0120258367
India
India
[e-mail]
1800 103 8009
South Korea
South Korea
[email protected]awei.com
N/A
North
America
USA
[e-mail]
1
-877-948-2934
Canada
[e-mail]
1
-855-482-9343
Latin America
Mexico
[e-mail]
018007703456
/0052
-442-4288288
Argentina
0
-8009993456
Brazil
0
-8005953456
Chile
800201866 (only for fixed)
Other countries
0052
-442-4288288
Middle East
and Africa
Egypt
[e-mail]
08002229000
/0020235353900
UAE
08002229000
South Africa
0800222900
Saudi Arabia
8001161177
Pakistan
0092512800019
Morocco
0800009900
Other countries
0020235353900