Huawei CR52-SRUA User manual

Quidway® NetEngine 40E Core Router Switch and Route Processing Unit
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 1
Quidway® NetEngine 40E Core Router
Switch and Route Processing Unit
Overview
The Switch and Route Processing Unit (SRU) is the core of the Quidway® NetEngine 40E Core
Router (“NE40E” hereinafter).
The NE40E has altogether 12 slots, two of which are for SRUs. The SRU supports hot plugging.
Each NE40E must be configured with one or two SRUs. It is recommended that two SRUs be
configured to implement redundant backup and raise the system reliability. Each SRU must be
configured with one or two Compact Flash (CF) cards (512MB) and memory cards(1GB). It is
recommended that two CF cards and two memory cards be configured to enhance the overall
performance of the system.
CR52-SRUA
The SRU mainly consists of the Main Processing Unit (MPU) and the Switch Fabric Unit (SFU). In
addition, it integrates the synchronous clock module (SYN), the line clock module (CLK), the
management communication module (MCX) and the CF card module. It is an integration of multiple
functional modules. As the system control and management center, and the system clock source
and maintenance&management unit, the SRU board completes control plane and system
maintenance plane functions.
The detailed functions are as follows:
1. System control and management center
zRouting protocol execution
All the routing protocol packets are sent by the forwarding engine to the SRU board for
processing. The SRU board also broadcasts and filters routing packets and executes routing
policies.

Quidway® NetEngine 40E Core Router Switch and Route Processing Unit
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 2
zOut-band communication path among the boards of the entire system
The SRU board integrates the LAN Switch module to provide inter-board out-band
communication for various boards. It completes control, maintenance and message exchange
among the SRU, SFU and Line Processing Unit (LPU).
zEquipment management and maintenance function
zData configuration function
The system configuration data, boot file, charging information, upgrade software and system
operation log are all saved on the SRU board. The SRU board provides a CF card interface as
a mass storage device to save data files.
zReliability guarantee
In view of reliability, the 1+1 redundant backup mode is adopted for the MPUs. The MPUs
monitor each other’s status. Once the active MPU is faulty, the standby MPU automatically
becomes active.
2. Component of the system switching network
Two SFU modules integrated on the SRU and two SFU boards together form four switching planes
that implement 3+1 load sharing.
3. System clock unit
The SRU board provides Synchronous Digital Hierarchy (SDH) interface clock signals of high
precision and high reliability to various line boards. It provides two 2.048MHz synchronous clock
signals to the downstream equipment and may receive external 2.048MHz or 2.048Mbps reference
clock.
4. Switching synchronous clock unit
It ensures the synchronization of the working clocks of the switching network and various line
boards.
5. System maintenance unit
This board collects the operating data of various system units via the monitoring bus, and
generates control information according to the operating states of these units. Such control
information concerns board in-position detection, switching network operating status control, fan
speeding up, and so on. The 1+1 hot backup mode is adopted for the MPU, clock and LAN Switch
modules of the board, which raises the system reliability.
Specifications
Currently, the NE40E provides one type of SRU: CR52-SRUA. The CR52-SRUA board provides
multiple external interfaces. Its specifications and functions are described in the following table:

Quidway® NetEngine 40E Core Router Switch and Route Processing Unit
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 3
Module
name Interface name Interface type Description
ETH0 port RJ45
Used to connect the system Network
Management workstation. It is
10/100/1000M adaptive and supports a
maximum transmission distance of 100m.
It provides LINK and ACT indicators.
ETH1 port RJ45
Used for interconnection of multiple
chassis but currently reserved. It is
10/100M adaptive and supports a
maximum transmission distance of 100m.
It provides LINK and ACT indicators.
Console port RJ45 RS-232 level; used to connect the console
and implement on-site configuration of the
system.
AUX port RJ45 RS-232 level; used to connect the Modem and implement remote maintenance
through dialing.
CF interface TYPE II standard (compatible with the
TYPE I standard)
Used to hold the CF card to save data
files. Standard configuration: 512MB
CLK-IN1
CLK-IN2 SMB Used to connect the external 2.048MHz or
2.048Mbps clock input.
CLK-OUT1
CR52-SRUA
CLK-OUT2 SMB Used to output the 2.048MHz or
2.048Mbps clock to the downstream
equipment.