Huawei eSpace IAD101H User manual

eSpace IAD101H/102H/104H Integrated
Access Device
V300R001C04
Quick Start
Issue
03
Date
2012-06-11
HUAWEI TECHNOLOGIES CO., LTD.

Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
i
Huawei Technologies Co., Ltd. provides customers with comprehensive technical
support and service. For any assistance, please contact our local office or company
headquarters.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://enterprise.huawei.com

Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
ii
Copyright © Huawei Technologies Co., Ltd. 2010-2012. All rights
reserved.
No part of this document may be reproduced or transmitted in any form or by any
means without prior written consent of Huawei Technologies Co., Ltd.
The product described in this manual may include copyrighted software of Huawei
Technologies Co., Ltd and possible licensors. Customers shall not in any manner
reproduce, distribute, modify, decompile, disassemble, decrypt, extract, reverse
engineer, lease, assign, or sublicense the said software, unless such restrictions are
prohibited by applicable laws or such actions are approved by respective copyright
holders under licenses.
Trademarks and Permissions
, ,
and are trademarks or registered trademarks of Huawei
Technologies Co., Ltd.
Other trademarks, product, service and company names mentioned are the property of
their respective owners.
Notice
Some features of the product and its accessories described herein rely on the software
installed, capacities and settings of local network, and may not be activated or may be
limited by local network operators or network service providers. Thus the descriptions
herein may not exactly match the product or its accessories you purchase.
Huawei Technologies Co., Ltd reserves the right to change or modify any information or
specifications contained in this manual without prior notice or obligation.
NO WARRANTY
THE CONTENTS OF THIS MANUAL ARE PROVIDED “AS IS”. EXCEPT AS
REQUIRED BY APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR
CONTENTS OF THIS MANUAL.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO CASE
SHALL HUAWEI TECHNOLOGIES CO., LTD BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, OR LOST PROFITS,
BUSINESS, REVENUE, DATA, GOODWILL OR ANTICIPATED SAVINGS.
Import and Export Regulations
Customers shall comply with all applicable export or import laws and regulations and
will obtain all necessary governmental permits and licenses in order to export, re-export
or import the product mentioned in this manual including the software and technical
data therein.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
Contents
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iii
Contents
1 Packing List............................................................................................................... 4
2 Safety Precautions ................................................................................................... 5
3 Installation ................................................................................................................ 7
4 Manual Configuration (CLI).................................................................................. 8
4.1 Logging In Through Telnet............................................................................................. 8
4.2 Connecting to NGN/IP PBX (SIP) ................................................................................. 9
4.3 Accessing NGN/IP PBX (MGCP)................................................................................ 14
4.4 Connecting to the IMS (SIP)........................................................................................ 19
4.5 Accessing Network Through the IAD .......................................................................... 24
5 Configuration (EMS)............................................................................................. 26
6 FAQs......................................................................................................................... 28
7 Technical Specifications and Environment Requirements............................ 30

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
1 Packing List
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4
1 Packing List
After you unpack the product package, check the items in the following table. If the
items in the package are different from those in the table, contact the sales person.
Item
Quantity
eSpace IAD101H/102H/104H
1
Power supply adapter
1
Network cable
1
CD-ROM
1
Quick Start
1
Certificate
1

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
2 Safety Precautions
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5
2 Safety Precautions
Pay attention to the following precautions when installing and using the device.
Basic Requirements
Follow the requirements of the manufacturer to install the device.
Do not disassemble the device. Contact the specified maintenance station if the
faults occur on the device.
Any company or person cannot change the design of the structure, security, or
performance without permission.
Comply with the related laws and regulations, and respect the legal rights of others
when using this device.
Usage Notice
Use the accessories shipped with the product and the recommended accessories,
such as the power supply adapters and batteries. The power supply voltage must
meet the requirement on the input voltage of the device.
Keep the power plug clean and dry to avoid the electric shock and other potential
risks.
Keep your hands dry when plugging in or out the device cable.
Stop the device and turn off the power before plugging in or out the device cable.
In the lightning weather, turn off the power and remove all the cables from the
device, such as the power cable, network cable, and phone cable. Otherwise, the
device may be damaged by the lightning.
If you do not need to use the device for a long time, turn off the power and remove
the power plug.
Keep the water and other liquids away from the device. If the liquid accidentally
flows into the device, turn off the power immediately and remove all the cables
from the device, such as the power cables and network cables. Contact the
specified maintenance station if faults occur.
Do not use the damaged or aged cables.
If exceptions occur, for example, the device is smoking, the sound is abnormal, or
the device turns smelly, stop using the device and turn off the power immediately.
Remove all the cables connected to the device, such as the power cables and
network cables. Contact the specified maintenance station when faults occur.
Prevent the objects (such as the metal) getting into the device from the heat
dissipation hole.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
2 Safety Precautions
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6
Avoid scratch or wear and tear on the device shell. Otherwise, the dropped paint
may cause allergy or device exceptions. For example, short circuit may be caused if
the paint drops into the host.
Keep children away from the device and accessories to avoid the dangerous
behaviors such as swallowing.
Cleaning Notice
Before you clean the device, stop the device and turn off the power. Remove all the
cables connected to the device, such as the power cables and network cables.
When you clean the device, do not use the liquid cleaner or spray cleaner to clean
the device shell. Use the soft cloth to wipe and clean the shell.
Environment Requirements
Keep the device dry when storing, transporting, and using the device.
Avoid the collision when storing, transporting, and using the device.
Place the device in the indoor environment with good ventilation and without direct
and strong sunlight.
Keep the device clean to avoid dust.
Do not place any object on the device to avoid the overheating of the device or
damage caused by extrusion.
Clear the space with the radius of over 10 cm around the device for heat
dissipation.
Keep the device away from the heat sources or exposed fire, such as the electrical
heater or candle.
Keep the device away from the appliance with the strong magnetic field or
intensive electric field, such as the microwave oven, fridge, or mobile phone.
Environment Protection
Do not discard the obsolete devices or batteries randomly. Discard them at the
specified recycle station.
Comply with the local laws and regulations on processing the device package
materials, consumed batteries, and obsolete devices, and support the recycling.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
3 Installation
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7
3 Installation
The eSpace Integrated Access Device 101H/102H/104H (eSpace
IAD101H/102H/104H) is the case-shaped device. You only need to connect cables.
The IAD101H/102H/104H installation is similar. The IAD102H is taken as an example.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8
4 Manual Configuration (CLI)
About This Chapter
You can use the CLI to configure all eSpace Integrated Access Device (IAD) functions.
The chapter describes how to configure about typical scenes and advanced parameters
by using the command line (CLI).In addition, some titles are marked with (SIP) or
(MGCP) to indicate that these service configurations can be implemented over SIP or
MGCP.
4.1 Logging In Through Telnet
The LAN port IP address of the IAD101H/102H/104H is 192.168.100.1 and 1.1.1.1 by
default. You can access the command line interface (CLI) of the IAD through
Telnet.For the IAD104H, serial port is an alternative access. The CLI includes an
interactive Help feature. You can enter a ?to obtain help and press Spacebar to
complete a command name.
Procedure
Step 1 Connect the network port of the PC to of the IAD101H/102H/104H by a network
cable, and then set IP addresses of the PC and IAD in the same network segment. For
example, the default IP address of the IAD is 192.168.100.1, the PC address of the PC
can be set to 192.168.100.2, and the subnet mask to 255.255.255.0. Ensure that you can
ping 192.168.100.1 successfully.
Step 2 Choose Start > Run, and enter "telnet" + a blank space + the actual IP address of the
IAD network port in the Run dialog box. Then click OK.
Step 3 After a connection is established, enter user name root and password admin to log in
to the IAD.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9
When you operate on the command line interface, you can enter a question mark (?) to
obtain help, press Spacebar to complete a command name, and press the arrow key ↑ to
show history commands.
If you cannot access the IAD by the preceding method, set the IP address of your PC to the
same IP address segment as "1.1.1.1" and the subnet mask to 255.255.255.0. If you can ping
1.1.1.1 successfully, enter telnet 1.1.1.1 in the Run dialog box to log in to the IAD.
----End
P.S. How to Log In to the IAD104H
Connect your PC to the IAD through a serial cable. Choose Start > Programs >
Accessories > Communication > HyperTerminal, input a name and select an icon in
the Connection Description, and select "COM1" in the Connect To dialog box (If
logging in to the CLI fails, select COM2). In the COM1 Properties dialog box, click
Restore Defaults and click OK. Press Enter on the HyperTerminal interface. After the
welcome interface is displayed. Enter the user name (root by default) and password
(admin by default).
4.2 Connecting to NGN/IP PBX (SIP)
The users of the IAD101H/102H/104H register with the softswitch (for example,
Softx3000 and SoftCo) to implement the voice service. After configuring the softswitch
data, configure the IAD101H/102H/104H data to use the voice service, including basic
call and fax services.
Data Preparation
In this example, the SoftCo functions as the softswitch. You can obtain the connection
data and other network data such as the default gateway between the IAD and the
SoftCo from the network carrier or network administrator. The following describes
how to enable the voice function for an IAD101H/102H/104H user.
Table 4-1 Connection data between the IAD and the Softswitch (for example, SoftCo)
Item
Value
Parameter and Value on the
IAD
Control protocol
used between the
softswitch and the
IAD
SIP protocol
Protocol mode: SIP
IP address of the
softswitch
192.169.1.40/255.255.25
5.0
IP address of the SIP server:
192.169.1.70

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10
Item
Value
Parameter and Value on the
IAD
IP address of the
IAD
192.169.1.62/255.255.25
5.0
IP address of the IAD:
192.169.1.62/255.255.255.0
NOTE
The IAD must be able to ping the
SIP server.
SIP signaling port
number on the
softswitch
5060
Server port number: 5060
SIP signaling port
number on the IAD
5060
local port: 5060
SIP user A
Device ID (eid): 8900
User number (dn):
8900
Authentication type:
authbyeid (based on
password)
Authentication
password: 1234
User ID for port 0: 8900
Password for port 0: 1234
NOTE
The user ID is the same as the
device ID on the softswitch,
that is, the EID on the SoftCo.
The user password on the
IAD is the same as the
authentication password on the
softswitch. The password may
be used when the softswitch
authenticates registered users.
Contact the network carrier or
softswitch administrator to
determine whether to set the
password and the specific
password.
SIP user B
Device ID (eid): 8901
User number (dn):
8901
Authentication type:
authbyeid (based on
password)
Authentication
password: 1235
User ID for port 1: 8901
Table 4-2 Other network information
Item
Data
IP address of the DNS server
192.169.1.50

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11
Item
Data
IP address of the uplink gateway
192.169.1.1
NOTE
The gateway IP address must be in the
same network segment as the IAD IP
address. Contact the network
administrator to obtain the gateway IP
address.
Procedure
Step 1 Enter the global configuration mode of the command line interface (CLI).
Open the CLI by using the user name root and password admin, and then run the
following commands.
Enter the privilege mode.
TERMINAL>enable
Enter the global configuration mode.
TERMINAL#configure terminal
If configuring the IAD will take a long time, modify the timeout interval to prevent
frequent automatic exit. (The default interval is five minutes and the maximum interval
is 255 minutes.) For example, set the timeout interval to 15 minutes.
TERMINAL(config)#terminal timeout 15
After the configuration is complete, run the exit command to exit the CLI to prevent
failure to re-open the CLI within the preset timeout interval.
After you exit the system, the timeout interval is reset to five minutes.
Step 2 Set the protocol mode.
Run the display protocol-mode command to view the current protocol mode. If the
SIP mode is not used, run the protocol-mode sip command to change the mode.
Step 3 Set the IAD IP address.
There are three modes for obtaining an IP address: static, DHCP, and PPPoE. By
default, the IP address of the IAD is 192.168.100.1 after being connected to the
network. You can also use other methods for obtaining the IP address:
static mode:
Run the ipaddress staticip-address subnet-mask default-gateway command to set a
fixed IP address. For example,
TERMINAL(config)#ipaddress static 192.169.1.62 255.255.255.0
192.169.1.1
DHCP mode:

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
12
Run the ipaddress dhcp command to obtain an IP address through DHCP. (A
DHCP server is required.) For example,
TERMINAL(config)#ipaddress dhcp
PPPoE mode:
A PPPoE server is required. The user name and password must be the same as
those on the PPPoE server. The command format is as follows:
−Run the pppoe usernameuser-namepasswordpassword command to set the
PPPoE user name and password.
−Run the ipaddress pppoe command to obtain an IP address through PPPoE.
−Run display pppoe to view the configuration of pppoe on the IAD.
For example,
TERMINAL(config)#ipaddress pppoe
TERMINAL(config)#pppoe username iad password ******
To view the IAD IP address, run the display ipaddress command.
When the DHCP or PPPoE mode is used, the IAD may take about eight minutes to
restart if the IAD cannot obtain the IP address in DHCP or PPPoE mode. Verify that the
DHCP or PPPoE server is available and the server information is correct.
Changing the IP address may disconnect the Telnet connection. Then, you should
establish the Telnet connection by using a new IP address.
Step 4 (Optional) Configure the DNS.
If the DNS server is available on the network, you can configure the DNS server on the
IAD so that the IAD can access other devices according to domain names.
1. Set the IP address of the DNS server
The command is dns serverip-address. For example:
TERMINAL(config)#dns server 191.168.10.50
2. (Optional) set a domain name suffix
The IAD automatically adds the domain name suffix to a domain name. The
command is dns domain-namedomain-name. For example, run the following
command to set the domain suffix to tele.com:
TERMINAL(config)#dns domain-name tele.com
In this case, if the domain name of the SIP server is set to softco, the IAD sends
softco.tele.com to the DNS server to obtain the IP address of the SIP server.
Run the display dns command to view the DNS status.
Step 5 Configure the SIP server.
Run the sip serverindexaddressip-address command to configure the IP address of the
SIP server.
TERMINAL(config)#sip server 0 address 192.169.1.40

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
13
There are three modes to obtain the IP address of the SIP server, consisting of STATIC, DNS
and DHCP.
If the DNS is configured, you can set the domain name of the SIP server in static mode
or select the DNS mode to configure the SIP server. For details, see the Manual
Configuration (CLI) in the CD-ROM.
If the IP address of the SIP server is obtained in DHCP mode, you can configure the SIP
server in DHCP mode.
By default, the IAD registers with the server whose index is 0. If the server is faulty,
the IAD registers with standby server 1. If standby server 1 is faulty, the IAD registers
with standby server 2. You can run the sip server-autoswitch enable command to
enable automatic switch between servers. The server whose index is 0 is the active
server, the servers whose indexes are 1 and 2 are standby servers. If the active server
has been restored when the IAD registers with a standby server, the IAD re-registers
with the active server.
Step 6 Configure the SIP user.
For details about mapping between user cable colors and ports, see in the Appendix.
Run the sip userport-numberidid command, where port-number is 0and id is
88880008 (the ID must have been set on the SIP server; otherwise, the user cannot
register with the SIP server).
TERMINAL(config)#sip user 0 id 8900
TERMINAL(config)#sip user 0 id 8901
Run the display sip attribute port-number command to view the configuration result.
Step 7 (Optional) Synchronize the system time with the SNTP server time.
This provides log and alarm records with an accurate time for reference.
Choose the SNTP server:
You can configure a computer as the SNTP server where the Windows Time service
is enabled. The computer must be always on. To check whether the Windows Time
service is enabled on a computer, choose Control Panel > Management Tools >
Services.
If you configure a computer as the SNTP server, make sure the firewall of the computer is
closed.
If the SIP server provides the SNTP service, you can configure the SIP server as the
SNTP server.
Synchronize the system time with the SNTP server time:
1. Run the sntp server address ip-address command to set the IP address for an
SNTP server.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
14
If the DNS is configured, you can run the sntp server name domain-name command to set
the SNTP server domain name.
2. Run the sntp interval<0-3600> command to set the synchronization interval. If
the synchronization interval is 0, the system time of the IAD does not synchronize
with the SNTP server time.
3. Run the sntp time-zone {+<0-13> | -<1-12>} command to set the time zone. For
example, to set the Beijing time, which is in the time zone GMT+8.
TERMINAL(config)#sntp time-zone + 8
You can run the display sntp command to view the SNTP server status.
TERMINAL(config)#display sntp
-------------------------------------------------
SNTP server : 191.168.10.44
Local time zone : +8
Synchronization interval : 2Sec.
state : available
-------------------------------------------------
Step 8 Run the write command to save the settings.
The command is:
TERMINAL(config)#write
----End
4.3 Accessing NGN/IP PBX (MGCP)
The users of the IAD101H/102H/104H register with the softswitch (for example,
Softx3000 and SoftCo) to implement the voice service. After configuring the softswitch
data, configure the IAD101H/102H/104H data to use the voice service, including basic
call and fax services.
Data Plan
In this example, the Softx3000 functions as the MGC server. You can obtain the
connection data between the IAD and the Softx3000 from the network carrier or
network administrator. The following data is for reference only.
Table 4-3 Connection data between the IAD and the Softx3000
Item
Parameter Value
Parameter and Value on the
IAD
Control protocol
used between the
SoftX3000 and the
IAD
MGCP protocol
Protocol mode: MGCP

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
15
Item
Parameter Value
Parameter and Value on the
IAD
IP address of the
IFMI board on the
SoftX3000
192.169.1.70/255.255.25
5.0
IP address of the MGC server:
192.169.1.70
IP address of the
IAD
192.169.1.62/255.255.25
5.0
IP address of the IAD:
192.169.1.62/255.255.255.0
NOTE
The IAD must be able to ping the
MGC server.
Domain name of
the IAD
shenzhen
MG domain name: shenzhen
MGCP local UDP
port number on the
Softx3000
2727
MGC port number: 2727
MGCP local UDP
port number on the
IAD
2427
MG port number: 2427
Encryption
algorithm
MD5
Authentication mode:
HW-Mode
Encryption key
12345678
Key: 12345678
Number of the user
A (whose device ID
is 0)
6540000
User number for port 0:
6540000
Number of the user
B (whose device ID
is 1)
6540001
User number for port 1:
6540001
Table 4-4 Other network information
Item
Data
IP address of the DNS server
192.169.1.50
IP address of the uplink gateway
192.169.1.1
NOTE
The gateway IP address must be in the
same network segment as the IAD IP
address. Contact the network
administrator to obtain the gateway IP
address.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
16
Procedure
Step 1 Enter the global configuration mode of the command line interface (CLI).
Open the CLI by using the user name root and password admin, and then run the
following commands.
Enter the privilege mode.
TERMINAL>enable
Enter the global configuration mode.
TERMINAL#configure terminal
If configuring the IAD will take a long time, modify the timeout interval to prevent
frequent automatic exit. (The default interval is five minutes and the maximum interval
is 255 minutes.) For example, set the timeout interval to 15 minutes.
TERMINAL(config)#terminal timeout 15
After the configuration is complete, run the exit command to exit the CLI to prevent
failure to re-open the CLI within the preset timeout interval.
After you exit the system, the timeout interval is reset to five minutes.
Step 2 Set the protocol mode.
Run the display protocol-mode command to view the current protocol mode. If not
MGCP mode, run the protocol mode mgcp command to change the mode.
Step 3 Set the IAD IP address.
There are three modes for obtaining an IP address: static, DHCP, and PPPoE. By
default, the IP address of the IAD is 192.168.100.1 after being connected to the
network. You can also use other methods for obtaining the IP address:
static mode:
Run the ipaddress staticip-address subnet-mask default-gateway command to set a
fixed IP address. For example,
TERMINAL(config)#ipaddress static 192.169.1.62 255.255.255.0
192.169.1.1
DHCP mode:
Run the ipaddress dhcp command to obtain an IP address through DHCP. (A
DHCP server is required.) For example,
TERMINAL(config)#ipaddress dhcp
PPPoE mode:
A PPPoE server is required. The user name and password must be the same as
those on the PPPoE server. The command format is as follows:
−Run the pppoe usernameuser-namepasswordpassword command to set the
PPPoE user name and password.
−Run the ipaddress pppoe command to obtain an IP address through PPPoE.
−Run display pppoe to view the configuration of pppoe on the IAD.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
17
For example,
TERMINAL(config)#ipaddress pppoe
TERMINAL(config)#pppoe username iad password ******
To view the IAD IP address, run the display ipaddress command.
When the DHCP or PPPoE mode is used, the IAD may take about eight minutes to
restart if the IAD cannot obtain the IP address in DHCP or PPPoE mode. Verify that the
DHCP or PPPoE server is available and the server information is correct.
Changing the IP address may disconnect the Telnet connection. Then, you should
establish the Telnet connection by using a new IP address.
Step 4 Set the registered domain.
Run mgcp mg-domain-name name. The name of the IAD, which is registered on the
MGC server, is iad001.
TERMINAL(config)#mgcp mg-domain-name iad001
You can run undo mgcp mg-domain-name to delete the registered domain of the IAD.
Step 5 (Optional) Configure the DNS.
Run dns server ip-address to set the IP address of the DNS server. Then the IAD can
access other network devices according to their domain names.
You can also run dns domain-name domain-name to set the domain name suffix that
indicates where the IAD is located. The IAD automatically adds the domain name
suffix when accessing other network devices according to domain names. For example,
if the domain name suffix is set to tele.com, and the domain name of the MGC server
is softco, the IAD automatically sends the softco.tele.com domain name to the DNS
server for parsing when accessing the MGC server. (Note: The IP address
corresponding to the domain name must be set on the DNS server so that the domain
name can be parsed successfully.)
You can run display dns to view the status of the DNS.
Step 6 Configure the MGC server.
Run mgcp mgc index address ip-address. The index is 1, and the IP address is
191.168.10.20.
TERMINAL(config)#mgcp mgc 1 address 191.168.10.20
If the DNS is configured, you can run mgcp mgc index address domain-name to set the
address of the MGC server.
You can set the index to 2 to configure a backup MGC server. The IAD registers to the
MGC server of index 1; if the registration fails, the IAD registers to the MGC server of
index 2 to ensure the normal running of the service.
Run display mgcp attribute to view the configuration result.
Step 7 (Optional) Synchronize the system time with the SNTP server time.

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
18
This provides log and alarm records with an accurate time for reference.
Choose the SNTP server:
You can configure a computer as the SNTP server where the Windows Time service
is enabled. The computer must be always on. To check whether the Windows Time
service is enabled on a computer, choose Control Panel > Management Tools >
Services.
If you configure a computer as the SNTP server, make sure the firewall of the computer is
closed.
If the SIP server provides the SNTP service, you can configure the SIP server as the
SNTP server.
Synchronize the system time with the SNTP server time:
1. Run the sntp server address ip-address command to set the IP address for an
SNTP server.
If the DNS is configured, you can run the sntp server name domain-name command to set
the SNTP server domain name.
2. Run the sntp interval<0-3600> command to set the synchronization interval. If
the synchronization interval is 0, the system time of the IAD does not synchronize
with the SNTP server time.
3. Run the sntp time-zone {+<0-13> | -<1-12>} command to set the time zone. For
example, to set the Beijing time, which is in the time zone GMT+8.
TERMINAL(config)#sntp time-zone + 8
You can run the display sntp command to view the SNTP server status.
TERMINAL(config)#display sntp
-------------------------------------------------
SNTP server : 191.168.10.44
Local time zone : +8
Synchronization interval : 2Sec.
state : available
-------------------------------------------------
Step 8 (Optional) Configure the MG authentication information.
Run mgcp authentication to prevent illegal MG devices from registering with the
MGC server.
Step 9 Run the following command to save your settings:
TERMINAL(config)#write
----End

eSpace IAD101H/102H/104H Integrated Access
Device
Quick Start
4 Manual Configuration (CLI)
Issue 03 (2012-06-11)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
19
4.4 Connecting to the IMS (SIP)
The IAD101H/102H/104H can connect to the IMS directly or through SoftSwitch. If
the IAD connects to the IMS through SoftSwitch, configure the IAD according to the
scenario where the IAD connects to the IP PBX. This topic describes the scenario
where IAD users directly register with the IMS. After configuring data on the IMS,
configure the IAD101H/102H/104H so that the IAD101H/102H/104H can provide
voice services, including basic call and fax services.
Data Plan
You can obtain the connection data between the IAD and the IMS from the network
carrier or network administrator. The following describes how to enable the voice
function for an IAD101H/102H/104H user.
Table 4-5 Connection data between the IAD and the IMS
Item
Value
Parameter and Value on the
IAD
Control protocol
used between the
IMS and the IAD
SIP protocol
Protocol mode: SIP
IP address of the
SBC server
192.169.1.40/255.255.25
5.0
IP address of the SIP server:
192.169.1.40
NOTE
The IP address of the SIP server
is the IP address of the P-CSCF
or SBC. Set the parameter based
on the site requirements.
IP address of the
IAD
192.169.1.62/255.255.25
5.0
IP address of the IAD:
192.169.1.62/255.255.255.0
NOTE
The IAD must be able to ping the
SIP server.
SIP signaling port
number on the IAD
5060
Server port number: 5060
SIP signaling port
number on the IAD
5060
Local port number: 5060
Domain name of
the IAD
abc.def.com
User domain name: abc.def.com
NOTE
The user domain name must be
unique.