Huawei WS7200 User manual

Quick Start Guide

Contents
Quick Start Guide ................................................... 1
Guide de démarrage rapide ................................... 16
Schnellstartanleitung ............................................ 31
Guida rapida ....................................................... 46
Snelstartgids ....................................................... 61
Guia de início rápido ............................................. 76
Guía de inicio rápido ............................................. 91

1
Getting Started (WS7100)
Quick Start Guide
POWER RESETLAN1 LAN2 LAN3WAN
3 4 671 25
RESET button Power button: Press once to power on the device, or
press and hold for at least three seconds to power it o.
WAN port: Connect to optical modems, broadband modems, etc.
LAN port: Connect to a wired Internet device, such as a computer.
Power portH button Indicator
2 3
4
5
67
1

2
Getting Started (WS7200)
POWER RESETLAN1 LAN2 LAN3WAN
4 5 78
3
126
NFC detection area
RESET button Power button: Press once to power on the device, or
press and hold for at least three seconds to power it o.
WAN port: Connect to optical modems, broadband modems, etc.
LAN port: Connect to a wired Internet device, such as a computer.
Power portH button Indicator
2 3 4
5
6
7 8
1

3
Step 1: Connecting the cables
POWER RESETLAN1 LAN2 LAN3WAN
POWER
LAN
PON
RESET
HUAWEI WiFi AX3
WAN
LAN Internet
Optical/Broadband/cable modem
(from your broadband provider)
•Erect the all antennas upright to ensure optimized Wi-Fi®signal.
•If the indicator stays red, this indicates that the router is not connected to the Internet.
Please refer to "Step 2: Conguring the network settings".

4
1Connect your mobile phone or computer
to the router’s Wi-Fi network (no
password required).
Check for the Wi-Fi name on the bottom of
the new router.
XXXXXX
Wi-Fi Name: XXXXXX
Wi-Fi
Wi-Fi
Connected
2Open the browser, you will be
automatically redirected.
( If the page is not displayed
automatically, enter 192.168.3.1) .
Let's get started
Step 2: Conguring the network settings

5
3Enter your broadband account and password.
If your Internet connection does not require an account and password, please skip to
the next step.
Internet access wizard
Broadband account
Broadband password
VLAN
Next
•If you have forgotten your broadband
account and password, contact your
broadband carrier to obtain a broadband
account and password.
• If you need to congure VLAN on your
network, contact your broadband carrier to
conrm the VLAN parameters, and enable
the VLAN switch on the screen.

6
4Set a new Wi-Fi name, Wi-Fi password, and admin password for the new router.
Internet access wizard
Prioritize 5 GHz
Wi-Fi network name
Wi-Fi network password
Admin password
Next
Internet access wizard
Conguration complete.
Enable Prioritize 5 GHz: Priority usage of 5 GHz Wi-Fi band over 2.4 GHz band when signal
strength is equal to increase connection speeds.

7
Indicator
Steady green
Steady red
Flashing
Connected to the network
Not connected to the network
•Loose cable or connect error. Check the cable.
•Broadband network error. Contact your broadband carrier.
The router has detected a pairable device.
When other HUAWEI routers (with H or Hi button) are detected, the
indicator on the HUAWEI WiFi AX3 will ash. When this happens, press
the HUAWEI WiFi AX3's H button. The indicator should flash quickly,
indicating that the pairable device is connecting to the HUAWEI WiFi AX3.
The connection process is complete when the indicator stops ashing.
•If you touched the H button by accident, wait for 2 minutes till the
indicator returns to normal.
•The H button also features WPS functionality.
Manage the router with our mobile app
Scan the QR code to download and install the HUAWEI smart
device management app on your mobile phone or tablet.You can
use the app to manage your router.

8
Frequently Asked Questions (FAQ)
Q1: What can I do if I encounter any of the following issues when conguring the router?
•If your device did not detect the router's Wi-Fi: Ensure that the router is powered on. Wait for a
moment (till the router is started) and try to search again on your device.
•If you cannot visit the router's conguration page on your device: Ensure that your device is
connected to the router's Wi-Fi network, and then enter 192.168.3.1 in the browser to visit this
page on your device.
•If the page displays "Cable disconnected": Ensure that the router's WAN port is connected to
the modem's LAN port, and the modem has Internet access. Check that all joints are securely
connected and in good contact, and the network cables are in good condition.
If the issue persists, restore the router to the factory settings, and follow the guide to reconnect the
cables and congure the router.
Q2: How do I restore the router to its factory settings?
Connect the router to the power supply and wait until the router completes the startup process.
Use a needle or pin to press the RESET button on the router for more than two seconds until the
indicator light goes out. Wait for the router to complete the restart process. When the indicator
turns red, this indicates that the router has been restored to its factory settings.
If the router has been factory reset, you need to congure it again.

9
Q5: What should I do if I forget my login password for the app or the router's web-
based management page?
Try using the router's Wi-Fi password to login. If the issue persists, restore the router to the
factory settings.
Q3: How do I connect an add-on HUAWEI router (with H/Hi button) to my HUAWEI WiFi
AX3's network?
You can connect the router in either of the following ways:
•Wired connection. Connect the WAN port of the add-on router (new or restored to factory
settings) to the LAN port of the congured HUAWEI WiFi AX3 using an Ethernet cable.
•Wireless connection (using the Hbutton). Step 1: Place the add-on router (new or restored to
factory settings) within one meter of the congured HUAWEI WiFi AX3 and connect it to the
power supply. Step 2: When the indicator on the HUAWEI WiFi AX3 starts to ash, press the H
button on it. Wait until the indicator on the add-on router shows it is connected to the network.
The following HUAWEI device models are supported: WS5800, WS7100 and WS7200. For details about
more device models, see the device manual.
Q4: How do I connect a Wi-Fi device to my router using WPS?
When your router is powered on, press its H button, and then press the WPS button on the Wi-Fi
device (such as a phone) within two minutes, to initiate standard WPS negotiation and connect
the Wi-Fi device to the router's Wi-Fi network.

10
Q7: How do I use the NFC function of the router to quickly connect to the Wi-Fi network?
Unlock your phone, enable NFC on it, and touch the NFC area on the back against the NFC area
on the router, then follow the onscreen instructions to connect the phone to the Wi-Fi network.
This feature is available on Android devices that support NFC, but some devices with non-standard NFC
may be unable to connect. iOS devices do not support connecting through NFC.
Q6: What should I do if some of my devices cannot nd or connect to the Wi-Fi?
This router supports Wi-Fi 6, which is the new generation Wi-Fi technology that can improve
network speeds for Wi-Fi 6 devices. However, some earlier devices, such as laptops using Intel
network adapters, may not be able to nd or connect to the Wi-Fi due to compatibility issues. In
this case, try to update the software version of the devices by referring to the device instruction
manual, or perform the following operations:
Update the router and the HUAWEI smart device management app to the latest version. Then
open the app, touch the router icon, touch Show more, search for and enable Wi-Fi 5 backup
network, and connect your device to the Wi-Fi 5 network.

11
Safety information
Operation and safety
• Do not use your device if using the device is prohibited. Do not use the device if doing so
causes danger or interference with other electronic devices.
• Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained
between a device and a pacemaker to prevent potential interference with the pacemaker.
If using a pacemaker, hold the device on the side opposite the pacemaker and do not carry
the device in your front pocket.
• Avoid dusty, damp, or dirty environments. Avoid magnetic elds. Using the device in these
environments may result in circuit malfunctions.
• Ideal operating temperatures are 0 °C to 40 °C. Ideal storage temperatures are -40 °C to +70 °C.
Extreme heat or cold may damage your device or accessories.
• Keep the device and accessories in a well-ventilated and cool area away from direct
sunlight. Do not enclose or cover your device with towels or other objects. Do not place the
device in a container with poor heat dissipation, such as a box or bag.
• The device should be installed and operated with a minimum distance of 20 cm between
the radiator and your body.
• Using an unapproved or incompatible power adapter, charger, or battery may damage your
device, shorten its lifespan, or cause a re, explosion, or other hazards.

12
• For pluggable devices, the socket-outlet shall be installed near the devices and shall be
easily accessible.
• Unplug the power adapter from electrical outlets and the device when not in use.
• Do not touch the device or the charger with wet hands. Doing so may lead to short circuits,
malfunctions, or electric shocks.
Disposal and recycling information
The symbol on the product, battery, literature, or packaging means that the products
and batteries should be taken to separate waste collection points designated by local
authorities at the end of the lifespan. This will ensure that EEE waste is recycled and
treated in a manner that conserves valuable materials and protects human health and
the environment.
For more information, please contact your local authorities, retailer, or household waste
disposal service or visit the website https://consumer.huawei.com/en/.
Reduction of hazardous substances
This device and its electrical accessories comply with local applicable rules on the restriction
of the use of certain hazardous substances in electrical and electronic equipment, such as
EU REACH regulation, RoHS and Batteries (where included) directive. For declarations of
conformity about REACH and RoHS, please visit the website
https://consumer.huawei.com/certication.

13
EU regulatory conformance
Statement
Hereby, Huawei Device Co., Ltd. declares that this device WS7100/WS7200 is in compliance
with the following Directive: RED 2014/53/EU, RoHS 2011/65/EU, ErP 2009/125/EC.
The full text of the EU declaration of conformity, the detailed ErP information and most recent
information about accessories & software are available at the following internet address:
https://consumer.huawei.com/certication.
Restrictions in the 5 GHz band:
The 5150 to 5350 MHz frequency range is restricted to indoor use only in: AT, BE, BG, CH, CY,
CZ, DE, DK, EE, EL, ES, FI, FR, HR, HU, IE, IS, IT, LI, LT, LU, LV, MT, NL, NO, PL, PT, RO, SE, SI, SK,
TR, UK.
Frequency Bands and Power
The frequency bands and transmitting power (radiated and/or conducted) nominal limits
applicable to this radio equipment are as follows: Wi-Fi 2.4G: 20 dBm, Wi-Fi 5G: 5150-5350
MHz: 23 dBm, 5470-5725 MHz: 30 dBm.

14
Legal Notice
Copyright © Huawei 2020. All rights reserved.
THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE ANY
KIND OF WARRANTIES.
Trademarks and Permissions
Wi-Fi®, the Wi-Fi CERTIFIED logo, and the Wi-Fi logo are trademarks of Wi-Fi Alliance.
Other trademarks, product, service and company names mentioned may be the property of
their respective owners.
Version Update
In order to improve the security of the product and provide you with a better user experience,
we will push version update information to you on a regular basis when an important update
is released.
Privacy Policy
To better understand how we use and protect your personal information, please see the
privacy policy at http://consumer.huawei.com/privacy-policy.
End User License Agreement
Please read and agree to the End User License Agreement (HUAWEI EULA) on the product’s
management page before using the product.

15
For More Help
Please visit https://consumer.huawei.com/en/support/hotline for recently updated hotline and
email address in your country or region.

16
Mise en route (WS7100)
Guide de démarrage rapide
POWER RESETLAN1 LAN2 LAN3WAN
3 4 671 25
Bouton de réinitialisation Bouton marche/arrêt : appuyer une fois pour allumer
l'appareil, ou appuyer/maintenir pendant au moins 3
secondes pour l'éteindre.
Port WAN : pour la connexion de modems optiques, modems haut débit, etc.
Port LAN: pour la connexion d'appareils Internet laires, tels qu'un ordinateur.
Port d'alimentationBouton H Voyant
2 3
4
5
67
1

17
Mise en route (WS7200)
POWER RESETLAN1 LAN2 LAN3WAN
4 5 78
3
126
Zone de détection de NFC
Bouton de réinitialisation Bouton marche/arrêt : appuyer une fois pour allumer
l'appareil, ou appuyer/maintenir pendant au moins 3
secondes pour l'éteindre.
Port WAN : pour la connexion de modems optiques, modems haut débit, etc.
Port LAN: pour la connexion d'appareils Internet laires, tels qu'un ordinateur.
Port d'alimentationBouton H Voyant
2 3 4
5
6
7 8
1

18
Étape 1: brancher les câbles
POWER RESETLAN1 LAN2 LAN3WAN
POWER
LAN
PON
RESET
HUAWEI WiFi AX3
WAN
LAN Internet
Modem optique/haut débit/câble
(de votre fournisseur d'accès haut débit)
•Placez toutes les antennes en position verticale pour garantir un signal Wi-Fi®optimal.
• Si le voyant reste rouge, cela signie que le routeur n'est pas connecté à Internet.
Veuillez vous référer à "Étape 2 : congurer les paramètres réseau".