Huawei OptiXstar EG8010Hv6-10 User manual

Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code
Issue 02
Date 2022-11-02
HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2022. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specied in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every eort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: https://www.huawei.com
Email: [email protected]
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. i

Contents
1 Placing the Device................................................................................................................... 1
2 Connecting Cables................................................................................................................... 3
3 Indicator Description.............................................................................................................. 5
4 Technical Specications......................................................................................................... 7
5 FAQs............................................................................................................................................ 8
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code Contents
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. ii

1 Placing the Device
NO TE
● Do not install the ONT outdoors or in an outdoor cabinet.
● The ONT can be mounted onto a wall or placed on a desk. Do not install the ONT in
other modes, such as ceiling.
● Keep 10 cm clearance on all sides to ensure adequate ventilation.
● It is recommended that the computer and ONT be put far away from electric appliances
that generate strong magnetic or electric elds, such as microwave ovens.
Mounting an ONT on the Desk
The gure below shows an ONT that is horizontally placed on a desk.
NO TE
The appearance shown in this document may be dierent from the actual appearance of
the product. The actual product prevails.
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 1 Placing the Device
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 1

Mounting an ONT onto a Wall
1. Mark two positions with the same spacing as that between the two mounting
holes of the ONT using a marker on a wall.
2. Select a proper drill bit according to the outer diameter of the screws. Use a
hammer drill to drill the marked positions on the wall. Then clean the holes
and install two expansion bolts.
3. Use a screwdriver to fasten the screws into the expansion bolts, reserving 3
mm ends out of the wall, and mount the ONT onto the screws.
NO TE
It is recommended that the screw be about 4 mm in diameter and longer than 20 mm. The
screw head should be between 6mm and 9mm in diameter.
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 1 Placing the Device
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 2

2 Connecting Cables
NO TE
● The ber connector connected to the optical port on the wall varies depending on
actual conditions.
● To ensure normal use of bers, make sure that the ber bending radius is larger than 30
mm.
No. Item Description
1 ON/OFF Powers the ONT on or o.
2 POWER Connects to a power adapter.
3 LAN Connects to PCs or IP set-top boxes (STBs).
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 2 Connecting Cables
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 3

No. Item Description
4 OPTICAL The optical port is equipped with a rubber plug and
connected to a ber for upstream transmission.
The type of the optical connector connected to the
optical port can be SC/APC.
5 Reset Press the button for a short time to reset the device,
or press the button for a long time (longer than 10s)
to restore the device to the default settings and
reset the device.
NOTE
Reset Huawei ONTs with caution. Otherwise, the ONTs
may fail to access the Internet. If an ONT cannot access
the Internet after a reset, contact your Internet service
provider.
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 2 Connecting Cables
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 4

3 Indicator Description
Indicator Status Description
POWER Steady on The ONT is powered on.
O The power supply is cut o.
PON/LOS See the following table.
LAN Steady on The Ethernet connection is in the normal
state.
Blinking Data is being transmitted over the
Ethernet port.
O The Ethernet connection is not set up.
Status No. PON Status LOS Status Description
1O O The ONT is prohibited by the
upper-layer device or blinks
abnormally. Contact the
service provider for help.
2 Blinks twice a
second
Blinks twice a
second
3 Blinks twice a
second
O The ONT attempts to set up
a connection with its upper-
layer device.
4 Steady on O A connection is set up
between the ONT and its
upper-layer device.
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 3 Indicator Description
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 5

Status No. PON Status LOS Status Description
5O Blinks once
every 2
seconds
The ONT is not connected to
bers or does not receive
optical signals.
6 Blinks once
every 2
seconds
Blinks once
every 2
seconds
The hardware is faulty.
NO TE
If the ONT is not powered on or the power switch is turned o, all indicators are o.
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 3 Indicator Description
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 6

4 Technical Specications
Product Function
Huawei OptiXstar
EG8010Hv6-10
1 Ethernet port
● Power adapter input: See the nameplate on the adapter.
● System power supply: See the nameplate on the device.
● Ambient temperature: 0ºC to +40ºC
● Ambient humidity: 5%–95% (non-condensing)
● Dimensions (H x W x D): 26 mm x 69 mm x 83 mm
● Weight: About 80g
● Maximum system power consumption: 2.1 W
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 4 Technical Specications
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 7

5 FAQs
NO TE
The following web page is only for reference. The actual web page of the product prevails.
How do I log in to the Huawei ONT web page?
NO TE
You are advised to use the latest browser to log in to the web conguration page. Chrome
58/Edge 14/Firefox 54/Safari 10/Opera 55 or later is recommended. If the browser of an
earlier version is used, compatibility issues may occur.
1. Use a network cable to connect a PC to the Huawei ONT.
2. Set the IP address of the PC in the same subnet as the web address of the
Huawei ONT.
For example, if the web address of the Huawei ONT is
192.168.a.b (for the web address of the Huawei ONT, see the product
nameplate), set the IP address of the PC to 192.168.a.c.
NO TE
The preceding cable connection diagram and login pages are only for reference, and
those of the actual product prevail.
3. Log in to the web conguration page.
a. Open a browser. In the address box, enter the web address (printed on
the nameplate of the Huawei ONT). Press Enter.
b. Enter the login user name and password (printed on the nameplate of
the Huawei ONT or contact your ISP). Click Log In.
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 5 FAQs
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 8

NO TE
● If you do not perform any operations after logging in to the system within five
minutes, you will be logged out, and the system automatically returns to the login
interface.
● The system will be locked for one minute if you input incorrect user name and
password for three consecutive times.
● Change the initial password after logging in to the web page for the rst time.
What can I do if the network speed is slow?
1. Check whether network cables are properly connected. Remove and then
insert the network cables. Then, check whether the network speed is normal.
2. Check whether downloading, network video watching, or other operations
occupy a large amount of bandwidth. Due to bandwidth restrictions, if some
network applications occupy a large amount of network bandwidth, the
network speed is slow.
3. Use another PC to check whether the network speed is normal.
How can I download Huawei ONT rmware or software?
Huawei ONT is used with an OLT and NMS of a required version. If the versions
are not the required ones, the ONT may not work.
If required, contact your internet service provider to obtain the correct ONT
rmware or software.
Huawei OptiXstar EG8010Hv6-10
Quick Start for QR code 5 FAQs
Issue 02 (2022-11-02) Copyright © Huawei Technologies Co., Ltd. 9