Huawei WS8800 User manual

Quick Start Guide
クイックスタートガイド
Model: WS8800
Product: HUAWEI WiFi Mesh 7

Contents
Quick Start Guide ................................................... 1
クイックスタートガイド ....................................... 14

1
Quick Start Guide
Getting Started
1
4
2
3RESET button
WAN/LAN auto-adaptation port: Connects to the Internet
(such as optical modem, broadband modems, etc.) and
wired network device such as a computer.
Power port
H button
Scan the QR code to download and install the HUAWEI AI Life
App on your mobile phone or tablet. You can use the app to
manage your router.
Step 1: Install the app
If the app is already installed on your
phone, make sure you have the latest
version of the app.
1
2
34
1
POWER 2
3
RESET
4
WAN/LAN

2
Step 2: Connect the cables
Connect your router to the optical/broadband/cable modem using
a network cable, then connect the router to a power supply.
Optical/broadband/cable modem
(from your broadband provider)
Router
Insert the cable to the
WAN/LAN auto-adaptation
port on the router
Internet
• If the indicator is steady red, this indicates that the router is not
connected to the Internet. Please refer to "Step 3: Set up the router".
• WAN/LAN auto-adaptation port: Connects to the Internet (such as
optical modem, broadband modems, etc.) and wired network device
such as a computer.
Step 3: Set up the router
Method 1: Congure the router on the app
Connect your mobile phone to the Wi-Fi
®of the router
connected to the modem (no password required). Check for
the Wi-Fi name on the bottom of the router.
1
WiFi
WiFi
Connected Wi-Fi Name: XXXXXX
POWER
LA N
ADSL
RESET
LAN WAN
1
POWER 2
3
RESET
4
WAN/LAN

3
Open the app. After the app has detected the router, touch
CONFIGURE.
If the prompt box does not appear,
touch +.
2
CONFIGURE
LATER
Touch GET STARTED and chose Create a Wi-Fi network.
3
GET STARTED
4Choose Internet access mode and enter your broadband
account and password.
If your Internet connection does not require an account and
password, please skip to the next step.
VLAN
Broadband account
Broadband password
Next
If you need to congure VLAN on
your network, contact your broadband
carrier to conrm the VLAN
parameters, and enable the VLAN
switch on the screen.
Internet access wizard
Create a Wi-Fi network
Extend a Wi-Fi network (relay)
Internet access wizard

4
...
Set a new Wi-Fi name, Wi-Fi password, and management
password for the new router.
5
Internet access wizard
Wi-Fi name
Wi-Fi password
Router login password
Internet access wizard Internet access wizard
Next Next
Set up Wi-Fi information

5
Method 2: Congure the router on the web-based
management page
Connect your mobile phone to the Wi-Fi of the router
connected to the modem (no password required). Check for
the Wi-Fi name on the bottom of the router.
1
2Open the browser and you will be automatically redirected
to the web-based management page (if the page is not
displayed automatically, enter "192.168.3.1" in the browser
address bar). Follow the onscreen instructions to congure
the router.
Get started
WiFi
WiFi
Connected Wi-Fi Name: XXXXXX

6
If the pack you purchased contains more than one router, the
other router(s) will set up a network with the rst congured
router automatically after being connected to the power supply.
Place the router(s) in the area where you wish to extend
Wi-Fi coverage, and connect it to a power supply. Wait for
approximately two minutes until the indicator turns steady blue,
indicating that the router is connected to the network. You can
also check their network connection through the app.
Step 4 (optional): Connect the other router(s)
to the power supply

7
• For best results, place the routers within 10 meters of each other
with one wall in-between at most.
• All routers share the same Wi-Fi name and password. When you
move across rooms, you will automatically connect to the faster
Wi-Fi network.
• If a router's indicator is steady red, this means that it cannot
connect to the Internet. Please refer to "Indicator - Steady red"
below for more details.

8
Indicator
Steady blue: Connected to the Internet.
Steady red: Not connected to the Internet.
Flashing: The router has detected a pairable device.
When other HUAWEI devices (support HarmonyOS Connect)
are detected, the indicator on the HUAWEI WiFi Mesh 7 will
ash. When this happens, touch the HUAWEI WiFi Mesh 7's
H button. The indicator should ash quickly, indicating that the
pairable device is connecting to the HUAWEI WiFi Mesh 7.
The connection process is complete when the indicator stops
ashing.
• If you touch the Hbutton accidentally, wait for approximately
two minutes and the indicator will be back to normal
automatically.
• The Hbutton also features WPS functionality.
For the router that is connected to the modem:
• Ensure that the Ethernet cable is not loose and connected
correctly.
• Contact your carrier to check for any network failure.
For the router(s) that is/are not connected to the modem.
• Ensure that the distance between two routers is less than 10
meters and there are no more than one wall in between.