Huawei FusionModule1000A40 ICT Solution User manual

FusionModule1000A40 Prefabricated All-in-One
Data Center
V200R003
Commissioning Guide
Issue
04
Date
2020-01-17
HUAWEI TECHNOLOGIES CO., LTD.

Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
i
Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
https://e.huawei.com

FusionModule1000A40 Prefabricated All-in-One Data
Center
Commissioning Guide
About This Document
Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
ii
About This Document
Purpose
This document describes how to power on and commission the FusionModule1000A
prefabricated all-in-one data center (FusionModule1000 for short) in terms of safety
precautions, preparations, power-on check, power on commissioning, joint commissioning,
power-off, and core device commissioning. It provides you a quick grasp of how to
commission the prefabricated all-in-one data center.
Intended Audience
This document is intended for:
Maintenance engineers
Technical support engineers
System engineers
Commissioning engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Indicates a hazard with a high level of risk which, if not
avoided, will result in death or serious injury.
Indicates a hazard with a medium level of risk which, if not
avoided, could result in death or serious injury.
Indicates a hazard with a low level of risk which, if not
avoided, could result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal
injury.

FusionModule1000A40 Prefabricated All-in-One Data
Center
Commissioning Guide
About This Document
Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
iii
Symbol
Description
Supplements the important information in the main text.
NOTE is used to address information not related to personal
injury, equipment damage, and environment deterioration.
Change History
Changes between document issues are cumulative. The latest document issue contains all
updates made in previous issues.
Issue 04 (2020-01-17)
Updated the USB description.
Issue 03 (2019-12-20)
Updated the safety information.
Issue 02 (2019-12-16)
Updated the USB description.
Updated the password change description.
Issue 01 (2018-03-01)
This issue is the first official release.

FusionModule1000A40 Prefabricated All-in-One Data
Center
Commissioning Guide
Contents
Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
iv
Contents
About This Document.................................................................................................................... ii
1 Safety Information........................................................................................................................1
1.1 General Safety ..............................................................................................................................................................1
1.2 Personnel Requirements ...............................................................................................................................................4
1.3 Electrical Safety............................................................................................................................................................4
1.4 Installation Environment Requirements .......................................................................................................................6
1.5 Mechanical Safety ........................................................................................................................................................7
1.6 Cooling System Safety ...............................................................................................................................................10
1.7 Pre-fab. Module Safety...............................................................................................................................................10
1.8 Battery Safety ............................................................................................................................................................. 11
1.9 Others..........................................................................................................................................................................13
2 Precautions for Power-On Commissioning ...........................................................................14
3 General power-on commissioning process............................................................................15
4 Preparations for Power-On Commissioning .........................................................................16
4.1 Tool Preparations........................................................................................................................................................16
4.2 Reference Documentation...........................................................................................................................................18
4.3 Commissioning Personnel Skill Requirements...........................................................................................................18
4.4 Preparing for the Power Supply and Distribution System Power-On Commissioning...............................................19
4.5 Preparing for the Cooling System Power-On Commissioning ...................................................................................20
4.6 Preparing for the Management System Power-On Commissioning ...........................................................................21
4.7 Preparing for the Fire Extinguishing System Power-On Commissioning...................................................................22
5 Check Before Power-On ............................................................................................................23
6 Power-On Commissioning........................................................................................................26
7 System Commissioning .............................................................................................................30
7.1 Power Supply and Distribution System Commissioning............................................................................................30
7.1.1 Verifying the Switchover Between Two Power Supplies.........................................................................................30
7.1.2 Commissioning the Logic Load Disconnection (Powering-Off) of the Power Supply System Under Normal
Temperature......................................................................................................................................................................31
7.2 Commissioning the Cooling System...........................................................................................................................32
7.3 The Management System Commissioning .................................................................................................................33

FusionModule1000A40 Prefabricated All-in-One Data
Center
Commissioning Guide
Contents
Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
v
7.3.1 Preparing for Commissioning the Management System..........................................................................................33
7.3.2 Commissioning the Management System................................................................................................................33
7.3.3 (Optional) Configuring the IP Address for an Outdoor Camera ..............................................................................34
7.4 Fire Extinguishing System Commissioning (CE).......................................................................................................38
8 Commissioning Core Components..........................................................................................45
8.1 Commissioning the UPS.............................................................................................................................................45
8.1.1 Commissioning the Integrated UPS.........................................................................................................................45
8.1.2 Commissioning the MDU........................................................................................................................................48
8.2 Commissioning Air Cooled Smart Cooling Products .................................................................................................51
8.2.1 Initial DIP Switch Configuration for T/H Sensors...................................................................................................53
8.2.2 Initial DIP Configuration for the Main Control Board.............................................................................................54
8.2.3 Teamwork Initial Configuration...............................................................................................................................56
8.2.4 Initial Configuration of Temperature and Humidity ................................................................................................64
8.3 Commissioning Monitoring Components...................................................................................................................66
8.3.1 Preparations and WebUI Login................................................................................................................................66
8.3.2 Commissioning Access Control Components..........................................................................................................70
8.4 Commissioning Fire Extinguishing Devices...............................................................................................................71
8.4.1 Commissioning the Extinguishant Control Panel (CE) ...........................................................................................71
8.4.2 Commissioning the Emergency Light (CE).............................................................................................................72
8.4.3 (Optional) Commissioning the VESDA ..................................................................................................................74
A Acronyms and Abbreviations..................................................................................................76

FusionModule1000A40 Prefabricated All-in-One Data
Center
Commissioning Guide
1 Safety Information
Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
1
1 Safety Information
1.1 General Safety
Statement
Before installing, operating, and maintaining the equipment, read this document and observe
all the safety instructions on the equipment and in this document.
The"NOTICE", "CAUTION", "WARNING", and "DANGER" statements in this document do
not cover all the safety instructions. They are only supplements to the safety instructions.
Huawei will not be liable for any consequence caused by the violation of general safety
requirements or design, production, and usage safety standards.
Ensure that the equipment is used in environments that meet its design specifications.
Otherwise, the equipment may become faulty, and the resulting equipment malfunction,
component damage, personal injuries, or property damage are not covered under the warranty.
Follow local laws and regulations when installing, operating, or maintaining the equipment.
The safety instructions in this document are only supplements to local laws and regulations.
Huawei will not be liable for any consequences of the following circumstances:
Operation beyond the conditions specified in this document
Installation or use in environments which are not specified in relevant international or
national standards
Unauthorized modifications to the product or software code or removal of the product
Failure to follow the operation instructions and safety precautions on the product and in
this document
Equipment damage due to force majeure, such as earthquakes, fire, and storms
Damage caused during transportation by the customer
Storage conditions that do not meet the requirements specified in this document
General Requirements
Do not install, use, or operate outdoor equipment and cables (including but not limited to
moving equipment, operating equipment and cables, inserting connectors to or removing
connectors from signal ports connected to outdoor facilities, working at heights, and
performing outdoor installation) in harsh weather conditions such as lightning, rain,
snow, and level 6 or stronger wind.

FusionModule1000A40 Prefabricated All-in-One Data
Center
Commissioning Guide
1 Safety Information
Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
2
Before installing, operating, or maintaining the equipment, remove any conductive
objects such as watches or metal jewelry like bracelets, bangles, and rings to avoid
electric shock.
When installing, operating, or maintaining the equipment, wear dedicated protective
gears such as insulation gloves, goggles, and safety clothing, helmet, and shoes, as
shown in the following figure.
Follow the specified procedures for installation, operation, and maintenance.
Before handling a conductor surface or terminal, measure the contact point voltage and
ensure that there is no risk of electric shock.
After installing the equipment, remove idle packing materials such as cartons, foam,
plastics, and cable ties from the equipment area.
In the case of a fire, immediately leave the building or the equipment area, and turn on
the fire alarm bell or make an emergency call. Do not enter the building on fire in any
case.
Do not stop using protective devices. Pay attention to the warnings, cautions, and related
precautionary measures in this document and on the equipment. Promptly replace
warning labels that have worn out.
Keep irrelevant people away from the equipment. Only operators are allowed to access
the equipment.
Use insulated tools or tools with insulated handles, as shown in the following figure.

FusionModule1000A40 Prefabricated All-in-One Data
Center
Commissioning Guide
1 Safety Information
Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
3
All cable holes should be sealed. Seal the used cable holes with firestop putty. Seal the
unused cable holes with the caps delivered with the cabinet. The following figure shows
the criteria for correct sealing with firestop putty.
Do not scrawl, damage, or block any warning label on the equipment.
Tighten the screws using tools when installing the equipment.
Do not work with power on during installation.
Repaint any paint scratches caused during equipment transportation or installation in a
timely manner. Equipment with scratches cannot be exposed to an outdoor environment
for a long period of time.
Before operations, ensure that the equipment is firmly secured to the floor or other solid
objects, such as a wall or an installation rack.
Do not use water to clean electrical components inside or outside of a cabinet.
Do not change the structure or installation sequence of equipment without permission.
Do not touch a running fan with your fingers, components, screws, tools, or boards
before the fan is powered off or stops running.
Personal Safety
If there is a probability of personal injury or equipment damage during operations on the
equipment, immediately stop the operations, report the case to the supervisor, and take
feasible protective measures.
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to
telecommunication network voltage (TNV) circuits.

FusionModule1000A40 Prefabricated All-in-One Data
Center
Commissioning Guide
1 Safety Information
Issue 04 (2020-01-17)
Copyright © Huawei Technologies Co., Ltd.
4
Do not power on the equipment before it is installed or confirmed by professionals.
1.2 Personnel Requirements
Personnel who plan to install or maintain Huawei equipment must receive thorough
training, understand all necessary safety precautions, and be able to correctly perform all
operations.
Only qualified professionals or trained personnel are allowed to install, operate, and
maintain the equipment.
Only qualified professionals are allowed to remove safety facilities and inspect the
equipment.
Personnel who will operate the equipment, including operators, trained personnel, and
professionals, should possess the local national required qualifications in special
operations such as high-voltage operations, working at heights, and operations of special
equipment.
Professionals: personnel who are trained or experienced in equipment operations and are
clear of the sources and degree of various potential hazards in equipment installation,
operation, maintenance
Trained personnel: personnel who are technically trained, have required experience, are
aware of possible hazards on themselves in certain operations, and are able to take
protective measures to minimize the hazards on themselves and other people
Operators: operation personnel who may come in contact with the equipment, except
trained personnel and professionals
Only professionals or authorized personnel are allowed to replace the equipment or
components (including software).
1.3 Electrical Safety
Grounding
For the equipment that needs to be grounded, install the ground cable first when
installing the equipment and remove the ground cable last when removing the
equipment.
Do not damage the ground conductor.
Do not operate the equipment in the absence of a properly installed ground conductor.
Ensure that the equipment is connected permanently to the protective ground. Before
operating the equipment, check its electrical connection to ensure that it is securely
grounded.
General Requirements
Use dedicated insulated tools when performing high-voltage operations.
AC and DC Power