Huawei Quidway S5624F User manual

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 1
Quidway® S5600 Intelligent and Resilient Series
Switches Product Specification
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
Fixed port 24 10/100/1000Base-T
ports, 4 1000BASE-X SFP
(Combo) ports, and 2
dedicate high speed
stacking ports
48 10/100/1000Base-T, 4
1000BASE-X SFP
(Combo) ports, and 2
dedicate high speed
stacking ports
24 1000Base-X SFP
ports,
4 10/100/1000BASE-T
(Combo) , and 2 dedicate
high speed stacking ports
Extended slot 1 1 1 1 1
Extended module (1) 8 ports 1000Base-X SFP module
(2) 1 port Xenpak 10GE module
(3) 2 ports XFP 10GE module
Performance
Wire speed L2/L3
switching Port Switch capacity:
88Gbps
Throughput: 65.47Mpps
Port Switch capacity:
136Gbps
Throughput: 101.18Mpps
Port Switch capacity:
88Gbps
Throughput: 65 .47Mpps
Switching Fabric 192Gbps 240Gbps 192Gbps
Flash 16M 16M 16M 16M 16M
POE No Yes No Yes No
Switching mode Store and forward
Forwarding
Latency <40µs
SDRAM 128M
Layer 2 feature
MAC address
table Address self-learning
IEEE 802.1D standard
Up to 16K MAC addresses
Up to 1k static MAC addresses

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 2
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
VLAN 4k VLAN (IEEE802.1Q)
Voice VLAN
GVRP
Support Port-based VLAN
Protocol-based VLAN
Configure VLANs in batch
Stack IRF(DDM, DRR, DLA) Stack
up to 8 units in one stacking group
Up to 448GE or 384GE and 16 10GE in one stacking group
Stacking bandwidth 96Gbps
RMON on IRF
HGMP on IRF
Peer fabric port testing
Link aggregation Link aggregation through command lines
Dynamic link aggregation through LACP
Link aggregation across switches
Up to 8 GE or 4 10GE ports in each aggregation group
Up to 32 aggregation groups (each aggregation port must be of the same speed)
Manual link aggregation through command lines
Mirroring Many-to-one port mirroring (multiple monitored ports to one monitor port, N:1)
Traffic mirroring
STP/RSTP/MSTP IEEE 802.1D Spanning Tree Protocol (STP)
IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
IEEE 802.1s Multiple Spanning Tree Protocol instances (MSTP)
QinQ BPDU Tunnel
Flow control IEEE 802.3x (full duplex)
Back-pressure based flow control (half duplex)

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 3
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
Broadcast /
Multicast /
Unicast storm
suppression
Port rate ratio(1% granularity) and PPS based on suppression
QinQ VLAN-VPN or double tag
Layer 3 feature
IP routing Static routing
16K IP Routes
RIPv1/v2 (Routing Information Protocol v1, v2)
OSPF v2 (Open Shortest Path First )
4 ECMP(Equal Cost Multi-Path)
RIP equivalent route
BGP4
Multicast IGMP (Internet Group Management Protocol) v1 and v2
IGMP (Internet Group Management Protocol) snooping
IGMP Group Limit on Interface
256 multicast groups
Adding multicast MAC addresses manually
Multicast source port suppression
MVR(Multicast VLAN Registration)1
PIM-DM
PIM-SM
MSDP(Multicast Source Discovery Protocol)
Network Protocol VRRP (Virtual redundancy routing protocol)
DHCP server
DHCP Snooping (Dynamic Host Configuration Protocol Snooping)
DHCP Relay (Dynamic Host Configuration Protocol Relay)
1For detail information, please refer to S5600 Series Switch System Description.

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 4
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
DHCP Client
DHCP option 60
ARP (Address Resolution Protocol)
NTP (Network Time Protocol)
BOOTP (Bootstrap Protocol)
UDP helper
Convergence
Quality of service
(QoS)/
Access control
list (ACL)
Support bi-directional port rate-limiting, Committed Access Rate (CAR), GE port with
granularity of 64 Kbps and 10GE port with the granularity of 1 Mbps
Eight output queues on each port
Time-based QoS
Packet redirection
Three scheduling algorithms that can be set based on port and queue at the same
time:
• SP (Strict Priority)
• WRR (Weighted Round Robin)
• SP + WRR
Packet tagging based on 802.1p or DSCP preference
L2~L4 Packet filter providing filtering based on source/destination MAC address,
source/destination IP address, port, protocol, VLAN, VLAN range, MAC address range,
or invalid frame
QoS profile management, allowing QoS service scheme customization
Mirroring remote ports (Support RSPAN)
Flow statistics for ACL rules defined using the deny keyword
Improvements made for the depth-first order of ACL matching
DSCP (differentiated services code point) refined when defining ACL rules
Delivering ACLs in RADIUS

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 5
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
Configuring synchronization for the queue schedule of aggregation ports
Protocol packet priority
Controlling Telnet users
Security
Network Login Support Centralized MAC address authentication
Support Disconnect unauthorized device (DUD) authentication
Support Port isolation
Support MAC address black hole
Support MAC Address Learning Limit
Prevent unauthorized access to the network by binding of MAC, IP and PORT
Support SSH(Secure Shell) V2 ( Automatic RSA public key configuring)
Support Port security
Support EAD (endpoint admission defense)
802.1X Support IEEE 802.1X user authentication
Version checking (802.1 X supplicant system)
Guest VLAN
Dynamic VLAN
802.1 X PEAP/EAP/TLS/TTLS
Performing 802.1 X authentication and MAC address-based authentication
simultaneously
802.1 X -trusted MAC address
802.1 X client checking

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 6
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
AAA&Radius Separated authentication, authorization, and accounting
Authenticated users need to be authenticated again when the device restarts
Delivering of trunk ports and hybrid ports in Tag VLAN is supported when performing
802.1x authentications
The tag authentication method field is added to RADIUS protocol
HWTACACS
Management/ Maintenance
System
Configuration
and Management
Support CLI (Command Line Interface) configuration mode
Support Configuration via the console port
Support Local/Remote configuration via Telnet
Support Remote configuration via modem dial-up
Support System configuration with SNMP v1, 2 and 3
Support SNMP Agent logging
Support HGMP V2
Support RMON (Remote Monitoring) v1, 1/2/3/9 groups of MIBs
Support Quidway network management system
Web-based network management
File system
management and
seven-segment
display
Upgrading all the units of a fabric using the App (or BootROM, Web) files of a unit
Setting an App file of a fabric or a unit of a fabric to be the primary/a secondary
configuration file
Specifying a fabric or a unit of a fabric to use the primary configuration file, a secondary
configuration file, or no configuration file to start.
Performing specific file-related operations for a fabric or a unit of a fabric, such as
deleting files stored in the storage devices of an Ethernet switch, displaying the
information about specified files or directories in the storage devices of an Ethernet
switch, and clearing the recycle bin.
Customizing the password for entering the BOOT menu

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Hu
http://www.huawe awei Technologies Co., Ltd. All Rights Reserved. i.com/products/datacomm/ 7
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
Configuration file backup/recovery
Seven-segment display, which indicates the progress of loading software using
FTP/TFTP
System
Maintenance and
debugging
Detailed alarm/debug information output
Support Ping and Tracert
Support remote maintenance via Telnet Modems and SSH
Support HWping
Support System log
Hierarchical alarm management and alarm filtering
Support DLDP (Device Link Detection Protocol)
Saving debugging information into Flash
Displaying the information about all enabled types of debugging
Displaying the statistics of MAC addresses of a switch
Configuring Telnet users with specified source IP addresses/source ports
Setting the Daylight Saving Time
Loopback detection on ports
Support VCT(Virtual Cable Test)
Information
center Exporting switch synchronization information
Setting the format of time stamps to be sent to log hosts
Hardware configuration
Outline
dimension
(W×H×D) 440 mm ×43.6 mm ×420mm (17.32 in.×1.72 in. ×16.54 in.)
Weight 7.1Kg 7.4Kg 7.1Kg
Power
supply Power module
PSL130-AD: 130 W system output, AC/DC input
PSL480-AD24P: 24-port PoE power module, 180 W system output + 300 W PoE
output (AC input); 180 W system output + 370 W PoE output (DC input)
PSL180-AD: 180 W system output, AC/DC input

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 8
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
PSL480-AD48P: 48-port PoE power module, 180 W system output + 300 W PoE
output (AC input); 180 W system output + 740 W PoE output (DC input)
Input
voltage AC:
Rated voltage: 100V to 240V, 50 Hz to 60Hz
Maximum tolerance:90V to 264V, 50 Hz to 60Hz
DC:
Rated voltage: -48V to -60V
Maximum tolerance: -36V to -72V
Input DC
voltage
of PoE
power
module
The S5624P-PWR/S5648P-PWR must use the external PoE PSU recommended by us
as its DC input, but not the -48VDC power supply generally available in the equipment
room. Otherwise, the device may be damaged
DC input of the PoE power module:
Rated voltage: –53.5 V
Max voltage range: –52 to–55 V
RPS
power Supported
Maximum power
consumption S5624P: 170 W
S5648P: 230 W
S5624F: 170 W
S5624P-PWR: 540 W
S5648P-PWR: 600 W
When with PoE power supply:
S5624P-PWR: 540 W (DC input), 560 W (AC input)
S5648P-PWR: 970 W (DC input), 640 W (AC input)
MTBF (Years) 32.30 32.30 23.99 23.99 23.89
Noise parameter S5624P: 50.8 dBA
S5648P: 51.4 dBA
S5624F: 54.6 dBA

Quidway® S5600 Intelligent and Resilient Series Switches Product Specification
Copyright ©2007 Huawei Technologies Co., Ltd. All Rights Reserved.
http://www.huawei.com/products/datacomm/ 9
Features S5624P S5624P-PWR S5648P S5648P-PWR S5624F
S5624P-PWR: 51.8 dBA
S5648P-PWR: 52.2 dB
MTTR (hours) <2 <2 <2 <2 <2
Environment Operation temperature: 0°C ~ 45°C
Storage temperature: -40°C ~ 70°C
Operating humidity: 5% to 85% non-condensing
Relative humidity: 10% ~ 90%, non-condensing