Hubbell EnergyHUBB NX Energy Dashboard User manual

3905C 100621
NX Energy Dashboard
Installation Guide
701 Millennium Blvd. | Greenville, SC 29607 | [phone] | hubbellcontrolsolutions.com
Copyright © 2021 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.

3905C 100621
Table of Contents
Precautions.........................................................................................................................................................................................................................1
Description .........................................................................................................................................................................................................................1
Package Content ..............................................................................................................................................................................................................2
Installation ..........................................................................................................................................................................................................................3
Starting Up energyHUBB Controller..........................................................................................................................................................................4
NX Energy Dashboard INSTALLATION GUIDE
701 Millennium Blvd. | Greenville, SC 29607 | [phone] | hubbellcontrolsolutions.com
Copyright © 2021 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.

FOR REFERENCE ONLY
MOUNTING FEET SHOWN AS INSTALLED
SECTION A-A
SECTION B-B
AA
B
B
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
STANDARD ENCLOSURE
DESCRIPTION
ALL DIMENSIONS ARE IN INCHES
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE
CUSTOMER
DATE DWG
AH12106
±0.03 ±0.010
SCALE
10/26/16
AJC
DRAWN BY
AH12106
1, 3R, 4, 4X, 12
COLOR:
NEMA 250: TYPE
UNLESS SPECIFIED
TOLERANCES
PART NUMBER
.XX .XXX
ATAH12106
SPECIAL REQUIREMENTS
MATERIAL: POLYCARBONATE
THIS DRAWING IS THE SOLE AND EXCLUSIVE
PROPERTY OF ROBROY ENCLOSURES.
NO PART OF THIS DRAWING MAY BE
REPRODUCED, DISTRIBUTED, OR PUBLICALLY
DISPLAYED IN ANY FORM OR BY ANY MEANS
WITHOUT THE EXPRESS WRITTEN
PERMISSION OF ROBROY ENCLOSURES.
ALL RIGHTS RESERVED
UNDER THE COPYRIGHT LAWS.
COPYRIGHT ©ROBROY ENCLOSURES
STANDARD P/N:
CUSTOMER DWG:
COLOR STANDARD:
IEC 60529: IP66
N/A
PANTONE 7541 C
2016
Robroy Enclosures
500 Maple Street
Belding, Michigan 48809
Phone: [phone]
Fax: [phone]
ASSEMBLY:
1. (1) ACCESSORY KIT (WPPCACCKIT) SHALL BE PACKAGED LOOSELY INSIDE ENCLOSURE
HARDWARE INCLUDED:
-(4) #1/4-20 x 1/2 FLAT HEAD PHILLIPS MACHINE SCREW (RMSC1/4-20X.5FLPH)
-(4) #10-32 x 5/8 PAN HEAD PHILLIPS MACHINE SCREW (RMSC10/32X5/8SS)
-(4) #10-32 x 3/8 PAN HEAD SCREW (RMSC10/32X3/8ZN)
-(4) #10 WASHER (RMWAS10ZN)
2. (1) STYROFOAM SHEET SHALL BE PLACED ON TOP OF COVER INSIDE CARTON
REVISION HISTORY
REV DESCRIPTION DATE ENG
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
11.41
13.41
10.81
7.87
12.00
11.95
12.81 10.25
10.00
9.95
9.63
7.63
1.18
12.68
0.44
7.05
14.03
8.24
0.14 TYP
0.187 TYP
7.38
14.88
3905C 100621
1
NX Energy Dashboard INSTALLATION GUIDE
Description
The Hubbell Control Solutions’ NX energyHUBB™ hosts the energy dashboard. The energyHUBB system is housed in an
enclosure where its pre-wired and assembled on a DIN rail and connected to a DIN rail power supply. (See Figure 1)
The energyHUBB system contains a system processor, web server-based user interface, data storage and network
interface components required for system operation.
The energyHUBB module connects with the NX network through the Area Controller using a standard Ethernet cable.
A standard Ethernet connection is provided on the module itself which can be used to connect directly to the area
controller customer Ethernet port. Additionally, the energyHUBB module can also be connected to the building LAN
router. (See Figure 2)
The NEMA1 grade enclosure has a hinged locking door and is suitable for surface wall mounting in a conditioned
electrical room.
Precautions
Read and understand all instructions before beginning installation.
NOTICE: For installation by a licensed electrician in accordance with National and/or local Electrical Codes and the
following instructions.
• Disconnect switch or a circuit breaker must be provided and marked as the disconnecting device.
• Disconnect switch/circuit breaker must be within reach of operator.
CAUTION: RISK OF ELECTRICAL SHOCK. Turn power o at service panel before beginning installation. Never wire
energized electrical components.
CAUTION: USE COPPER CONDUCTOR ONLY
Conrm device ratings are suitable for application prior to installation. Use of device in applications beyond its
specied ratings or in applications other than its intended use may cause an unsafe condition and will void
manufacturer’s warranty.
NOTICE: Do not install if product appears to be damaged.
SAVE THESE INSTRUCTIONS!
Figure 1.
701 Millennium Blvd. | Greenville, SC 29607 | [phone] | hubbellcontrolsolutions.com
Copyright © 2021 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.

3905C 100621
2
NX Energy Dashboard INSTALLATION GUIDE
Package Content
• NX energyHUBB™ Enclosure Assembly
• Installation Guide
• Mounting Foot with Screws (optional to use)
• Wall Mounting screws not included
• Ethernet patch cables are not included.
Packaging Box with Shipping Label
Figure 2: Network Connection
Mounting Foot with Screws (in plastic bag)
NX energyHUBB Enclosure Assembly
701 Millennium Blvd. | Greenville, SC 29607 | [phone] | hubbellcontrolsolutions.com
Copyright © 2021 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.

30W Power
Supply
Ethernet
-
+
Ground
3905C 100621
3
NX Energy Dashboard INSTALLATION GUIDE
Installation
1. Do not install the NX energyHUBB in an unconditioned space.
2. The NX energyHUBB is shipped completely assembled but requires further installation and connections.
3. Identify a suitable location to mount the enclosure assembly. Ideally, it should be mounted right next to the NX Area
Controller.
4. Wall mount the enclosure assembly using appropriate mounting screws (not included) according to the 4 mounting
keyholes (See Figure 1). Note: An optional mounting foot with screws is provided for ease of wall mounting.
5. Open the enclosure door and identify the power cables (red and black wires.) Before proceeding further, ip open
the circuit breaker mounted inside the enclosure. Now proceed with connection to a power source of 120V.
Carefully follow the wire color markings on the power supply housing.
6. All additional connections to the NX energyHUBB will be made using CAT5e cable with RJ-45 connectors.
7. The NX energyHUBB module housed inside the enclosure comes with a 10/100 Base-T Ethernet connection via the
RJ-45 Port. The RJ-45 port has two LEDs. When the device is connected to the network the blue LEDs are lit, and ash
when there is network activity.
8. Connect one end of your CAT5e Ethernet cable to the RJ-45 port and the other end to the Ethernet port on the NX
Area Controller. See Figure 3 & 4.
9. Use the second Ethernet port on the NX energyHUBB module to connect your PC. See Figure 3 & 4.
As an alternative option, if the user wants to connect the NX energyHUBB to their building LAN network, use the
second RJ-45 port on the module to connect the building router instead of the PC. Refer to the diagram in Figure 2.
10. Route the Ethernet and power cables through the provided knock-outs as shown in Figure 3.
11. Make sure to close the enclosure door once all connections and installation is complete.
To NX Area Controller and PC/LAN
Primary RJ-45 Port
Connect NX Area Controller Here
Secondary RJ-45 Port
Connect your PC Here
To Main Power (120V 60Hz)
Figure 3: Key Access Points
701 Millennium Blvd. | Greenville, SC 29607 | [phone] | hubbellcontrolsolutions.com
Copyright © 2021 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.

3905C 100621
4
NX Energy Dashboard INSTALLATION GUIDE
To NX Area Controller
To PC/LAN
NX Area Controller, Interior
From NX energyHUBB
Figure 4: Network Connections
Starting Up energyHUBB Controller
1. Energize the circuit feeding the NX energyHUBB to power it up. Make sure to close the circuit breaker next to the
energyHUBB module inside the enclosure.
2. Ensure the PC is connected to the system and to the NX Area Controller as described in the previous section.
3. There are two RJ-45 Ethernet ports on the NX energyHUBB module (as shown in Figure 4). The primary port is
dedicated for connection to the NX Area Controller. Its default static IP address is 192.168.1.2
4. The secondary port of your NX energyHUBB ships with a static default IP address (192.168.0.3) from the factory. This
port is dedicated for customer connection, such as to your PC or your building LAN router.
5. To ensure energyHUBB has been connected properly and functioning, you need to connect your PC directly to the
NX energyHUBB module and make sure you can get to the dashboard login in screen.
In order to do this, you will need to follow some steps outlined below, starting with changing your computer’s
network adapter settings to be in the same network as energyHUBB.
6. In your network adapter settings, click on “Change Adapter Settings”, then click “Ethernet”.
a. Go to Ethernet Properties and select “Ethernet Protocol Version (TCP/IPv4) as shown above.
701 Millennium Blvd. | Greenville, SC 29607 | [phone] | hubbellcontrolsolutions.com
Copyright © 2021 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.

3905C 100621
5
NX Energy Dashboard INSTALLATION GUIDE
b. Manually enter the IP address (as shown below). The IP address must be 192.168.0.x where x must be a number
other than 3 (it can be anywhere between 4 and 250). The subnet eld should populate automatically as you
enter the IP address.
c. Click OK when done.
7. Open your browser (Internet Explorer or equal) and type 192.168.0.3 into the URL address line at the top of the page
and press “Enter”. This is the default IP address of the energyHUBB as shipped from the factory.
The NX energyHUBB Login Screen* will now appear.
8. Use the following default login details to log into the web portal:
Default user name: admin
Default password: EnergyHUBB
9. Upon a successful login, you are now ready to handover the conguration of the energyHUBB System and BACnet
integration to your startup technician.
• There is no guarantee that the network can still be discovered and commissioned successfully by the startup
technician.
• It is contingent upon all devices in the system being connected properly and functioning.
• Work with your start-up technician to nd out if there are any wiring, connection or functionality issues in the system.
• Refer to the NX energyHUBB User Guide for complete details on network conguration and steps for a successful
system startup.
*Please Note: Login screen design is subject to changes over time, however the log-in process will remain the same as
described here.
701 Millennium Blvd. | Greenville, SC 29607 | [phone] | hubbellcontrolsolutions.com
Copyright © 2021 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.