Hunter 42797-01 Instruction manual

Type 3 ModelsType 3 ModelsType 3 Models
Form# 42797-01
20081113
©2008 Hunter Fan Co.
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
English Español
Owner’s Guide and Installation Manual
Westside II
21621

2
42797-01 • 11/13/08 • Hunter Fan Company
© 2008 Hunter Fan Company
Your new Hunter® ceiling fan is an addition to your home or oce that
will provide comfort and performance for many years. is installation
and operation manual gives you complete instructions for installing
and operating your fan.
We are proud of our work. We appreciate the opportunity to supply
you with the best ceiling fan available anywhere in the world.
Before installing your fan, for your records and warranty assistance,
record information from the carton and Hunter nameplate label
(located on the top of the fan motor housing).
Cautions and Warnings
•READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING
INSTALLATION. SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts.
• To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to these instructions,
and use only the hardware supplied.
• To avoid possible electrical shock, before installing your fan,
disconnect the power by turning o the circuit breakers to the
outlet box and associated wall switch location. If you cannot lock
the circuit breakers in the o position, securely fasten a prominent
warning device, such as a tag, to the service panel.
• All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualied electrician.
• To reduce the risk of personal injury, do not bend the blade
attachment system when installing, balancing, or cleaning the fan.
Never insert foreign objects between rotating fan blades.
• To reduce the risk of re, electrical shock, or motor damage, do not
use a solid-state speed control with this fan. Use only Hunter speed
controls.
Welcome
Table Of Contents
1 • Getting Ready......................4
2 • Installing the Ceiling Plate ..........5
3 • Assembling the Top Housing .......6
4 • Assembling and Hanging the Fan ...7
5 • Setting the Remote Transmitter and
Receiver...........................8
6 • Wiring the Fan .....................9
7 • Installing the Canopy ...............11
8 • Assembling the Blades..............12
9 • Completing Your Installation .......13
10 • Operating the Remote Control and
Mounting the Holder..............14
11 • Operating and Cleaning Your Ceiling
Fan ...............................15
12 • Troubleshooting ..................16

3
42797-01 • 11/13/08 • Hunter Fan Company
Installer’s Choice and Optional Accessories
Understanding Mounting and Installer’s Choice®
Hunter’s patented 3-position mounting system provides you maximum
installation exibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Prole, Standard, or Angled mounting. e steps in this manual include
instructions for all three Installer’s Choice mounting methods.
Considering Optional Accessories
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
For ceilings higher than 8 feet, you can purchase
Hunter extension downrods. All Hunter fans use
sturdy 3/4 in. diameter pipe to assure stability and
wobble-free performance.
Standard Mounting hangs from the
ceiling by a downrod (included).
Angled Mounting recommended for a
vaulted or angled ceiling
Support Brace
Standard
Mounting
Style
Ceiling
Outlet Box
Support Brace
Ceiling
Outlet Box
Angled
Mounting
Style
Low Profile Mounting ts close to the
ceiling, recommended for ceilings less
than 8 feet high
Support Brace
Low Prole
Mounting
Style
Ceiling
Outlet Box
8
12
CAUTION: To
reduce the risk of
personal injury, attach
the fan directly to the
support structure of
the building according
to these instructions,
and use only the
hardware supplied.

4
42797-01 • 11/13/08 • Hunter Fan Company
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64 in. bit
• Standard screwdriver (magnetic tip recommended)
• Phillips-head screwdriver (magnetic tip recommended)
• Wrench or pliers
• Ladder (height dependent upon installation site)
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326.
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum eciency, and energy savings.
Installing Multiple Fans?
If you are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in sets,
as they were shipped.
1 • Getting Ready

5
42797-01 • 11/13/08 • Hunter Fan Company
CAUTION: To avoid possible electrical shock, before installing your fan,
disconnect the power by turning o the circuit breakers to the outlet box
and associated wall switch location. If you cannot lock the circuit breakers
in the o position, securely fasten a prominent warning device, such as a
tag, to the service panel.
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. e pilot holes should have a
diameter of 9/64 in.
2-2. Your fan comes with three neoprene noise isolators (“Isolators”).
Position the isolators between the ceiling plate and ceiling by
inserting the raised areas on each isolator into the holes in the
ceiling plate.
2-3. read the lead wires from the outlet box down through the hole
in the middle of the ceiling plate.
2-4. Align the slotted holes in the ceiling plate with the pilot holes you
drilled in the wood support structure. For proper alignment use
slotted holes directly across from each other.
Note: e isolators should be ush against the ceiling.
2-5. Place a at washer on each of the two 3 in. wood screws and pass
the screws through the slotted holes in the ceiling plate into the
pilot holes you drilled.
Tighten the screws into the 9/64 in. pilot holes; do not use
lubricants on the screws. Do not over tighten.
Step 2-2
Flat Washer
3 in. Wood Screw
Steps 2-3 – 2-5
For Angled Ceilings: Be sure to orient
the ceiling plate so that the hook and
one of the threaded screw holes in the
ceiling plate are on the lower side.
Ceiling
Plate
Isolator
2 • Installing the Ceiling Plate

6
42797-01 • 11/13/08 • Hunter Fan Company
3 • Assembling the Top Housing
3-1. To assemble the housing to the hanger adapter, align the three
raised tabs on the hanger adapter with the three narrow notches
in the top housing. Make certain the housing sits at on the
adapter.
3-2. Install three (3) assembly screws and tighten them securely.
Steps 3-1 – 3-2
Top Housing
Assembly Screw
Hanger Adapter

7
42797-01 • 11/13/08 • Hunter Fan Company
4 • Assembling and Hanging the Fan
Steps 4-4 – 4-5
Low Prole Screw
Low Prole Washer
Steps 4-1 – 4-2
Downrod
Canopy
You can assemble your fan for standard mounting (steps 4-1 – 4-2)
or for low prole mounting (steps 4-3 – 4-5). Note: For low prole
mounting, the downrod is replaced with the low prole washer.
4-1. To assemble fan to hang down from a at or angled ceiling, insert
the downrod through the canopy. Feed the wires from the fan
through the downrod.
4-2. Loosen the square head set screw on the adapter to install the
pipe and ball assembly. Note: When the pipe and ball assembly
is fully installed, 2-3 threads on the pipe will still be visible; this is
normal. Securely retighten the set screw with a wrench or pliers.
Skip to Step 4-6.
CAUTION: e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
4-3. Remove the set screw from the adapter.
4-4. Place the low prole washer (lip down) into the canopy. Be sure
the green ground wire is pointing up toward the ceiling.
4-5. Align the holes in the washer with the holes in the adapter.
Assemble securely with three low prole screws.
Note: Before hanging the fan, align and engage the two tabs from the
bottom of the canopy and the two grooves in the hanger ball.
4-6. Raise the fan and place the hook on the ceiling plate through the
round hole in the rim.
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Step 4-6
Round
Hole

8
42797-01 • 11/13/08 • Hunter Fan Company
5 • Setting the Remote Transmitter and Receiver
CAUTION: e remote control device complies with part 15 of the FCC rules.
Changes or modications not expressly approved by Hunter Fan Company could void
your authority to operate this equipment.
Operation is subject to the following two conditions:
1. is device may not cause harmful interference.
2. is device must accept any interference received, including interference that may
cause undesired operation.
WARNING: Use only the Hunter Fan speed control supplied with this fan.
IMPORTANT! Before you change the jumper settings, make sure the
battery is not connected to the transmitter.
5-1. Change the position of the jumpers in the remote transmitter
and the receiver. Make sure that the jumpers match in the remote
receiver and transmitter. If they don’t match, the transmitter will
not function.
5-2. Install the included 12-volt battery into the transmitter.
Setting Transmitter and Receiver Codes
When two or more fans are located near each other, you may desire
to have the receiver/transmitter for each fan set to a dierent code,
so that the operation of one fan does not aect the operation of the
other fans.
e jumpers for the receiver are located on the at surface of
the receiver. e jumpers for the transmitter are in the battery
compartment. e jumpers are very small; you can move them most
easily using a small pair of pliers or tweezers.
4321
4321
4321
4321
4 = off
3 = on
2 = on
1 = on
4 = off
3 = on
2 = off
1 = on
Receiver Jumpers
4321
4321
4321
4321
4 = off
3 = on
2 = on
1 = on
4 = off
3 = on
2 = off
1 = on
Example Jumpers Settings
Receiver 1 Receiver 2
Transmitter 2Transmitter 1
4321
4321
4321
4321
4 = off
3 = on
2 = on
1 = on
4 = off
3 = on
2 = off
1 = on

9
42797-01 • 11/13/08 • Hunter Fan Company
6 • Wiring the Fan
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
Wall switches are not included. Select an acceptable general-use switch
in accordance with national and local electrical codes.
6-1. Disconnect the power by turning o the circuit breakers to the
outlet box and associated wall switch location.
6-2. Place the receiver inside the canopy, making sure that the
dipswitches and the oval shaped holes in the bottom of the
receiver are facing down toward the bottom of the canopy.
6-3. Spread the receiver lead wires to each side and feed the wires from
the top of the fan through the open slot in the receiver.
6-4. Place the receiver in the canopy. Make sure the slot in the receiver
is aligned with the hook in the ceiling plate.
6-5. To connect the wires, hold the bare metal leads together and
place a wire connector over them, then twist clockwise until tight.
Using the small wire connectors, connect the fan to the receiver as
follows:
• Connect the yellow wire from the fan to the yellow wire from
the receiver.
• Connect the pink wire from the fan to the pink wire from the
receiver.
• Connect the grey wire from the fan to the grey wire from the
receiver.
• Connect the red wire from the fan to the red wire from the
receiver.
• Connect the black wire with a white stripe from the fan to the
black wire with a white stripe from the receiver.
• Connect the white wire from the fan to the white wire
(LIGHT OUT) from the receiver.
Steps 6-5 – 6-6
Large Wire
connector
Small Wire
connector

10
42797-01 • 11/13/08 • Hunter Fan Company
6 • Wiring the Fan (Continued)
6-6. Using the large wire connectors, connect the fan and receiver to
the power wires as follows:
• Connect the white wire (A/C IN) from the receiver to the white
wire from the ceiling.
• Connect the black wire from the receiver to the black wire from
the ceiling.
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
6-7. Run the thin white antenna wire from the receiver through one
of the slots in the ceiling plate. (For best reception, make sure the
end of the antenna is exposed at the top of the canopy.)
6-8. Connect the green ground wires from the ceiling plate and the
downrod to the ground wire from the ceiling.
6-9. Push all wires and wire connectors back through the ceiling plate
hole into the outlet box. Place the green and white wires on a
separate side of the outlet box from the other wires.

11
42797-01 • 11/13/08 • Hunter Fan Company
7 • Installing the Canopy
7-1. Holding the canopy, raise the fan o the hook.
7-2. Align the holes in the canopy with the mounting holes on the
ceiling plate.
7-3. Insert and tighten the mounting screws securely.
Steps 7-1– 7-3
Mounting Screw
Canopy

12
42797-01 • 11/13/08 • Hunter Fan Company
3 • Assembling tbe Blades
Step 8-1
Step 8-2
Holes
Fan Motor 8-1. Insert blade into slot. Align the holes on the blade with the holes
in the fan motor.
8-2. Slide at washers onto the shafts of the blade assembly screws.
8-3. Attach the blade to the motor using the blade assembly screws.
8-4. Repeat for each blade.
Blade Assembly
Screw
Flat Washer
8 • Assembling the Blades
3 • Assembling tbe Blades

13
42797-01 • 11/13/08 • Hunter Fan Company
9 • Completing Your Installation
9-1. Partially install two light kit tter screws into the light kit
mounting plate.
9-2. read the plug connector from the fan through the light kit tter.
9-3. Align the keyholes in the light kit tter with the two partially
installed screws and rotate to engage the screws in the narrow
ends of the keyholes.
9-4. Install the remaining screw to secure the light kit tter to the light
kit mounting plate. Securely tighten all three screws.
9-5. Connect the 2-pin plug connector from the fan to the 2-pin plug
connector from the ballast.
9-6. Attach the ballast to the light kit tter with two ballast screws.
9-7. Install the included 22 Watt uorescent bulb into the hooks on
the tter.
9-8. Connect the 4 pin plug from the ballast to the uorescent bulb.
9-9. Place the glass globe into the globe trim band. Align the three
holes in the trim band with the three holes in the tter. Install and
securely tighten all three screws.
Steps 9-1 – 9-8
Step 9-9
Light Kit
Fitter Ballast
Fluorescent
Bulb
Glass
Globe
Globe
Trim
Band

14
42797-01 • 11/13/08 • Hunter Fan Company
10 • Operating the Remote Control and Mounting the Holder
10-1. e remote transmitter has individual buttons for turning the fan
o and on and controlling the light and fan speed.
10-2. For best operation, start the fan by pressing high, then select your
desired speed.
10-3. e reversing switch reverses the direction of the fan.
10-4. Press the OFF button to turn the fan o.
10-5. e light button turns the light on to full brightness. Push the
light button again to turn o the light.
10-6. You can mount the remote holder to any toggle switch plate with
the screws already in the switch plate. Or, you can simply mount
the remote holder on the wall.
10-7. is product includes one 12-volt type 23A, MN-21 battery for
use with the remote control transmitter. Please contact your local
battery recycling center for proper battery disposal information.
Step 10-6
Fan Light
Fan Speed
High
Fan Speed
Medium
Fan Speed
Low Fan O
Reversing Switch
Steps 10-1 – 10-5
Step 10-7

15
42797-01 • 11/13/08 • Hunter Fan Company
11 • Operating and Cleaning Your Ceiling Fan
11-1. Restore power at the main electrical panel and turn on the wall
switch. e light kit should turn ON.
Note: To turn on the light without the remote, turn o the wall
switch for 5 seconds, then back on. e light kit will turn on at
maximum brightness.
11-2. Press the remote control’s HIGH speed button. e fan should
start and reach its maximum speed.
Note: For everyday operation, leave the wall switch ON. If the
remote control will not be used for 5 days or more, turn the wall
switch OFF.
11-3. Ceiling fans work best by blowing air downward
(counterclockwise blade rotation) in warm weather to cool the
room with a direct breeze. In cold weather, having the fan draw
air upward (clockwise blade rotation) will distribute the warmer
air trapped at the ceiling around the room without causing a
draft.
11-4. For cleaning nishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier
dust. Remove surface smudges or accumulated dirt and dust
using a mild detergent and a slightly dampened cloth. You may
use an artistic agent, but never abrasive cleaning agents as they
will damage the nish.
11-5. Clean wood nish blades with a furniture polishing cloth.
Occasionally, apply a light coat of furniture polish for added
protection and beauty. Clean painted and high-gloss blades in
the same manner as the fan nish.
In warm weather, use
downward air ow pattern
In cold weather, use upward
air ow pattern

16
42797-01 • 11/13/08 • Hunter Fan Company
Hunter fans have the power to cut your cooling costs up to 40%.
Beat the High Cost of Cooling
e air movement created by a Hunter ceiling fan lets you set your
thermostat higher and still stay comfortable. Every degree you
raise the thermostat saves up to 7% on energy costs. So, you can
cut back on expensive air conditioning...and save up to 40%* on
cooling. In winter, your Hunter fan recirculates warm air and saves
up to 10%* on heating bills.
* On average at low speed settings. Your savings may vary based
on climate, building type and thermostat setting.
Save Energy and Money While Protecting the Environment
Congratulations! You’re saving energy and money while protecting
the environment by purchasing this ENERGY STAR qualied
Hunter ceiling fan! With this purchase, you are doing your part to
protect the environment. In 2010, ENERGY STAR qualied ceiling
fans are projected to cut air pollution by more than 500 million
pounds!
Your new ceiling fan has earned the ENERGY STAR label
because it meets high energy eciency specications set by
the Environmental Protection Agency (EPA). ENERGY STAR
labeled ceiling fans save energy because they have more ecient
fan motors and air delivery due to more aerodynamic blade
congurations. Ceiling fan models bearing the ENERGY STAR label
move air 14 - 20% more eciently than typical ceiling fan models.
For more information on ENERGY STAR visit www.energystar.gov.

17
42797-01 • 11/13/08 • Hunter Fan Company
12 • Troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the
fan section.
3. Check the plug connection in the switch housing.
Problem: Noisy operation.
1. Tighten the blade screws until snug.
2. Check to see if the blade is cracked. If so, replace all the blades.
3. Be sure that the glass is secure.
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2. Tighten all blade and/or blade iron screws.
3. Turn power o, support fan very carefully, and check that the
hanger ball is properly seated.
If you need parts or service assistance, please call
888-830-1326 or visit us at our Web site at
http://www.hunterfan.com.
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114