Hunter 9002X User manual

OWNER’S GUIDE
FOR MODELS 9002X & 9702X
41479-01 01/06/2005
®
The
CENTURY
High Performance Oscillating Fan
41479-01 Rev 01-06-05.pmd 1/6/05, 5:06 PM1

241479-01 01/06/2005
IMPORTANT SAFETY INFORMATION
Read & Save These Instructions
WARNING
To reduce the risk of fire or electrical
shock, DO NOT use this fan with any
solid-state speed control device.
CAUTION
When using electrical appliances, basic
precautions should always be taken to
reduce the risk of fire, electric shock
and personal injury:
1. Read all instructions before using
this fan.
2. Improper installation may result
in the risk of fire, electric shock
or personal injury.
3. To prevent the risk of fire and
electric shock, DO NOT use the
unit near windows. Rain and
moisture may create an electrical
hazard.
4. The power plug must be removed
from the power socket when not
in use, before cleaning, servicing,
maintenance and before moving
to another location.
5. DO NOT put fan in a damp place
or where humidity is high-such
as a bathroom.
6. The fan should be placed on a
flat, stable surface or tabletop
to avoid overturning.
7. Use fan only for intended use,
as described in this instruction
manual.
8. To protect against electrical
shock, DO NOT immerse unit,
plug or cord in water or spray
with liquids.
9. Close supervision is necessary
when any appliance is used by
or near children.
10. NEVER insert fingers, pencils or
any other objects through the
grill when the fan is running.
11. DO NOT operate any appliance
with a damaged cord or plug, af-
ter the appliance malfunctions or
has been dropped or damaged in
any manner.
12.To disconnect, grip plug and
pull from wall outlet. NEVER
yank on cord.
13. ALWAYS use on a dry surface.
14. This product is intended for
household use only and not for
commercial or industrial use.
15. DO NOT operate fan in the pres-
ence of explosive and/or flam-
mable fumes.
16. DO NOT place fan or any parts
near an open flame, cooking or
any other heating appliances.
17. DO NOT use near curtains, plants,
window treatments, etc.
18. This appliance has a grounded
three-prong plug and is suitable
for grounded receptacle use only.
An adapter is available for con-
necting three-blade grounding-
type plugs to two-slot recep-
tacles. The adapter must
be properly grounded. DO NOT
attempt to defeat the purpose
of this safely feature.
41479-01 Rev 01-06-05.pmd 1/6/05, 5:06 PM2

41479-01 01/06/2005 3
Please attach your
receipt or a copy of your
receipt to this manual
for future reference.
WELCOME UNPACKING
Thank you for choosing the Hunter
Century Table Fan. This manual gives
you complete instructions for using
your fan. Here are some the features
you will enjoy with your fan:
•An attractive design that enhances
any decor
•Apowerful Hunter motor for
maximum air flow
• Three speeds to adjust your com-
fort level
Before installing your fan, record the
following information for your
records and for warranty assistance.
Model Name ___________________
Date Code _____________________
Date Purchased _________________
Where Purchased _______________
______________________________
As you unpack the fan, save the car-
ton and packing materials in case
you want to move or ship the unit in
the future.
Carefully remove all items from
the box.
NOTE: It is best to have someone
hold the box while you lift the fan
and the protective packaging out of
the carton.
Make sure all shipping materials are
removed from fan before operating.
41479-01 Rev 01-06-05.pmd 1/6/05, 5:06 PM3

441479-01 01/06/2005
GROUNDING INSTRUCTIONS
WARNING
FIGURE 2FIGURE 1
Grounded
Plug
Grounding Pin Grounded Outlet
Box Cover
Grounded Outlet
Box Cover
Metal
Screw
Adapter
Grounding
Means
This appliance is for household use
only and may be plugged into any
120-volt AC electrical outlet (ordi-
nary household current). DO NOT
use any other type of outlet.
This unit is suitable for
grounded receptacle use only.
The cord has a grounded plug as
shown in Figure 1. An adapter, as
shown in Figure 2, is available for
connecting three-blade grounding-
type plugs to two-slot receptacles.
The green grounding lug extending
from the adapter must be connected
to a permanent ground such as a
property grounded outlet box. The
adapter should not be used if a
three-slot grounded receptacle is
available.
LINE CORD SAFETY TIPS
1. NEVER pull or yank on the cord
or the appliance.
2. To insert plug, grasp it firmly and
guide it into the outlet.
3. To disconnect the appliance,
grasp the plug and remove it
from the outlet.
4. Before each use, inspect the line
cord for cuts and/or abrasion
marks. If any are found, the ap-
pliance should be serviced and
the line cord replaced. Please re-
turn it to our Service Department
or to an authorized service repre-
sentative.
5. NEVER wrap the cord tightly
around the appliance, as this
could place undue stress on the
cord where it enters the appli-
ance and could cause it to fray
and break.
6. DO NOT operate appliance if the
line cord shows any damage, if
the appliance works intermit-
tently or stops working entirely.
41479-01 Rev 01-06-05.pmd 1/6/05, 5:06 PM4

41479-01 01/06/2005 5
OPERATION
FIGURE 3
This appliance is for household
use only.
1. Place the fan on a dry, safe, flat
surface where it cannot fall or be
pulled by the cord.
2. Plug the fan into a grounded
120-volt AC electrical outlet (or-
dinary household current).
DO NOT use any other type of
outlet. Make sure that the rated
voltage of the fan is the same as
the power source before plug-
ging it into the power source.
3. Turn the fan “ON” or “OFF” by
sliding the Power/Speed Control
to the right or left. The power
should always be OFF before un-
plugging the fan.
4. To select the speed, move the
Power/Speed Control from
OFF to the desired speed set-
ting: O (off), I (low), II (me-
dium), III (High).
5. To control the upward and
downward direction of airflow,
loosen the screw on the side of
the fan housing neck. Adjust
to the desired angle and
tighten the screw.
6. To make the fan oscillate, push
the oscillation knob down. To
stop oscillating, pull the oscilla-
tion knob up. The oscillation
knob is located on the top of the
fan housing, near the handle.
Handle
Oscillation
Knob
Motor
Housing
Up/Down
Adjustment
Screw
Base
Power/Speed
Control Switch
41479-01 Rev 01-06-05.pmd 1/6/05, 5:06 PM5

641479-01 01/06/2005
MAINTENANCE
FIGURE 4
This fan is permanently lubricated
and will not require additional lubri-
cation (oil) for the life of the fan.
This fan requires little maintenance
and contains no user serviceable
parts. DO NOT try to fix it yourself.
Contact qualified service personnel
if servicing is needed.
TO CLEAN:
1. Before cleaning, turn fan off and
unplug from electrical outlet.
Wipe off excess dust with a
lintfree cloth.
2. To ensure adequate air circula-
tion to the motor, keep vents lo-
cated at the rear of the motor
housing free from dust accumu-
lation. A vacuum cleaner hose
can be used to clean these vents.
3. DO NOT immerse the fan in wa-
ter or any other liquid.
CLEANING GRILL AND BLADE:
1. Turn the fan off and unplug from
the electrical outlet.
2. Disassemble grills by carefully re-
moving the screw on the bottom
of the grill and by squeezing the
ring to remove the hook from
the hole. See Figure 4.
3. Disassemble blades by carefully
removing the blade screw behind
the blades. The blades should
slide off.
4. Grills and blades may be cleaned
with mild soap and water.
5. Use a soft, slightly damp cloth to
wipe the remaining fan parts.
6. DO NOT allow water or any
other liquid to get into the mo-
tor housing or base.
7. Reassemble the fan after blades
and grills have dried completely.
First, replace the blades. When
replacing the blade screw, you
should feel some resistance as
the screw engages the bar. Next,
align the grills, replace the ring,
place the hook in the hole and
replace the screw.
8. DO NOT plug fan into an electri-
cal outlet until it has been fully
reassembled.
Front
Grill
Blade
Screw
Back
Grill
Handle
Oscillation
Knob
Motor
Housing
Up/Down
Adjustment
Screw
Base
Power/Speed
Control Switch
Blade
Ring
41479-01 Rev 01-06-05.pmd 1/6/05, 5:06 PM6

41479-01 01/06/2005 7
STORAGE TROUBLESHOOTING
1. Disassemble and clean fan be-
fore storing.
2. Keep the original packaging for
the purpose of storing the fan.
3. ALWAYS store the fan in a dry
place.
4. NEVER store the fan while it is
still plugged in.
5. NEVER wrap the cord tightly
around the fan.
6. DO NOT put any stress on the
cord where it enters the fan, as it
could cause the cord to break.
PROBLEM
•Fan will not oscillate.
SOLUTION
•Push down on knob on top of
motor housing to activate oscil-
lation.
PROBLEM
•Can not adjust the
angle of the fan.
SOLUTION
•Loosen the screw on the side of
the fan neck. Adjust to the desired
angle and tighten the screw.
If you have tried these troubleshoot-
ing solutions and still have trouble,
call 1-888-830-1326 (For CAN: 1-
866-268-1936) or visit our Web site
at http://www.hunterfan.com.
41479-01 Rev 01-06-05.pmd 1/6/05, 5:06 PM7

841479-01 01/06/2005
®
41479-01 Rev 01-06-05.pmd 1/6/05, 5:06 PM8