Hunter Bolivar User manual

Installation Manual
©2020 Hunter Fan Co.
Bolivar
Model: 59644 Matte Black
Fan weight ±2 lbs: 21.6 lbs (9.8 kg)
PG3904 r052820

Ladder
9/64” Drill Bit 5/32” Drill Bit Hex Head Ratchet
Socket Wrench
Drill
Screwdriver
Pliers Wire Strippers
OPTIONAL
Congratulations on purchasing your new Hunter®ceiling fan!
Here are the tools you’ll need to complete your installation:
1
The ceiling fan you purchased will provide comfort and performance in your home or ofce for many years. This
instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and
appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
We are here to help!
This Instruction Manual is designed to make installation as simple as possible. While working through this Instruction
Manual, keep your smartphone or tablet nearby. We have added video links to help you through the more technical
sections. If you are unfamiliar or uncomfortable with wiring, contact a qualied electrician. We also provide telephone
support at 1.888.830.1326 or visit us at HunterFan.com.
1886
WARNING
This product conforms to UL Standard 507.
Certied to CSA Standard C22.2 No. 113
READ and SAVE These Instructions
Warning
w.1 - To reduce the risk of re, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the
mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you
cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
w.3 – To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.
w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
Caution
c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied electrician.
c.2 - Use only Hunter replacement parts.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
If mounting to a support structure, you will also need these tools.

PB 2
1886
1886
x1
x1
x1
For installing secondary
hanging system
Lag Bolt
Washer
Plastic
Washer
bag
Do not discard the hardware bags or mix parts from
different bags. Make note of the symbol printed on
each hardware bag. The symbols can be used to
identify the appropriate hardware for each step.
x4
x2
x15 x15
x2
x2
x2
For installing the hanger bracket and wiring the fan
For installing the blades
For installing the canopy
For installing the light xture
bag
bag bag
Hunter Pro Tip:
Find a part that is missing or damaged?
Don’t take it back to the store. Let us make it right. Visit us at HunterFan.com or call us at 1.888.830.1326.
bag
Spare Parts
For your convenience,
you may receive extra fasteners. Pullchains and extra downrod
bag
Bulb
Switch Housing Plate
Globe
Switch Housing Assembly
Motor
Downrod
Blade Arm
Blade
Canopy Canopy Screw
Blade Screw
Blade Washer
Ceiling Bracket
Wood Screw
WIre Nut
Washer
x2
bag Light Kit Screws
Cover Plate Screws
Fan style may vary.
Note:
M3816-01 r052120
x5
x5
We recommend that you pull everything out of the box and lay it out. We have
grouped the drawn components below with the hardware you’ll need for those
parts. The screws below are drawn to scale to make it easier to identify what
piece of hardware is needed to install each component.
Here is what comes in your box:
x3
Blade Arm Screw
x10
bag

34
1886
1886
Choosing the Right Installation Location
Checking the Ceiling Angle:
Angled Mounting
You probably bought this fan with a location in mind. Let’s check below to make sure it is a good t.
If you have an angled or vaulted ceiling:
1. You will need a longer downrod. (sold separately at HunterFan.com)
2. If your ceiling angle is greater than 34°, you will also need an
Angled Mounting Kit. (Sold separately at HunterFan.com)
Check the room dimensions: Check the outlet box:
You must be able to
secure the fan to building
structure or fan-rated
outlet box.
30 inches
from blade tip to
nearest wall or
obstruction 7 feet
from bottom edge
of blade to the
oor
Support
Structure
Ceiling
Outlet Box
(required)
Angled Mounting
If you have a at ceiling:
Hang your fan by a standard downrod. Some fans come
with a shorter downrod for a Low Prole installation.
Support Structure
Ceiling
Outlet Box
(required)
Standard Mounting
A little more information on Angled Mounting:
For optimum performance and appearance, a longer downrod should
be used with your Hunter ceiling fan when installing on high or angled
ceiling. If your ceiling is angled greater than 34°you will also need an
Angled Mounting Kit. Longer downrods and the Angled Mounting Kit are
sold separately at HunterFan.com.
Determining if you need an Angled Mounting Kit:
Fold on the dotted line. Place against edge againts
the wall. Slide towards the ceiling.
If the guide touches the wall but not the ceiling, you
need an angled mounting kit.
Hunter Pro Tip:
CEILING
WALL
34°
Installing the Ceiling Bracket

34
1886
1886
Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Glass/Bulbs
Check the outlet box:
WARNING
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Installing the Ceiling Bracket
Use wood screws and
washers (included) when
securing to support structure
with approved electrical
outlet box. Drill 9/64” pilot
holes in support structure
to aid in securing ceiling
bracket with hardware found
in the hardware bag.
Use machine screws
(provided with outlet box)
and washers when securing
to existing ceiling fan-rated
outlet box. Make sure it is
securely installed and is
acceptable for fan support of
31.8 kg (70 lbs) or less.
Option 2:
Wood Screws
Option 1:
Machine Screws
The machine screws are the ones
that came with your outlet box.
Hunter Pro Tip:
For angled ceilings,
point opening
toward peak.
ANGLED
MOUNTING TIP
bag
Wood Screw
Washer x2
x2
You have two options for installation. Pick which one works best for your location. Remove any existing
bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box.
Installing the Secondary Hanging System
OFF
Turn Power
Do this rst!
NOTICE
Do you have an exposed support structure?
Go to www.HunterFan.com/FAQs and click
“Where do I connect the cable to?
Drill a 5/32” pilot hole through
the Ceiling Fan Rated outlet box
and into the support structure.
Remove the lag bolt, metal
washer, and plastic washer
from the bag. Thread
the lag bolt through the
metal washer and then the
plastic washer.
Using a hex head ratchet socket wrench, screw
the lag bolt and washers found in the bag
into the pilot hole. Leave 3 mm (1/8”) of space
between the outlet box and the plastic washer.
NOTE: Completion of hanging
system is on pg 5
WARNING
To reduce the risk of re, electrical shock, or personal injury,
mount fan directly from building structure and/or an outlet box
marked acceptable for fan support of 70 lbs (31.8 kg) and use the
mounting screws provided with the outlet box. x1
x1
x1Lag Bolt
Washer
Plastic
Washer
bag

56
1886
1886
Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Glass/Bulbs
Wiring the Fan
Hanging the Fan
S
l
i
d
e
c
a
n
o
p
y
o
v
e
r
d
o
w
n
r
o
d
a
n
d
w
i
r
e
s
.
DO NOT PICK THE FAN UP BY THE CANOPY
OR WIRES. Place the downrod ball into the
slot in the ceiling bracket.
NOTICE
To prevent damage to fan,
ALWAYS lift holding either the
fan housing or the downrod.
Installing the Downrod
Follow below if you are using the downrod that came
pre-assembled in your box. Need to install a longer or
shorter downrod? Check out the guide at the end of
this manual.
8”
3/8”
C
U
T
&
S
T
R
I
P
(not to scale)
Pass all wires to one side of horizontal
bar in downrod assembly. Hand tighten
the downrod (at least 4–5 full turns)
until it stops. Trim the wires coming
from the fan so that 8-inches remain
coming from the top of the downrod.
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
K
E
E
P
!
2
3
1
STEP
STEP
STEP
Hunter Pro Tip:
The ground wire attached to the
downrod is approximately 8 inches.
WARNING
FAN FALL HAZARD
To prevent SERIOUS INJURY or DEATH:
• ALWAYS tighten setscrew with pliers.
• DO NOT hand tighten setscrew.
• CHECK the setscrew is tight using pliers
each time you change fan direction.
Remove the pre-installed
setscrew so that the
downrod can be inserted.
Installing the Secondary Hanging System
Hook the looped end of the cable over the
lag bolt so that the cable is between the
plastic washer and the outlet box.
Tighten the loop then tighten the lag bolt using
a hex head ratchet socket wrench. Coil up the
excess cable.
NOTICE
If you have a different conguration
than shown or have a downrod
accessory, consult a qualied
installer and/or electrician.

56
1886
1886
Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Glass/Bulbs
Wiring the Fan
We know wiring is hard. Let’s make it easier.
You are going to need these:
4 Wire Nuts (these are in the bag)
Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch
setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualied electrician.
Have a single switch?
Follow these steps:
Have dual switches?
Follow these steps:
Hunter Pro Tip:
Here is how to connect the wires:
Push the bare metal ends of the wires together and slide a wire
nut over them. Then, twist the wire nut clockwise until tight.
Give it a gentle pull to make sure none of the wires are loose.
Connect the white
(grounded) wire
from the ceiling
to the white wire
from the fan.
Connect the white
(grounded) wire
from the ceiling
to the white wire
from the fan.
Connect the second ungrounded
(light) wire from the ceiling to
the blue wire from the fan.
Connect the three
grounding wires (green,
green/yellow stripe, or
bare copper) coming from
the ceiling, downrod, and
hanging bracket.
Connect the three
grounding wires (green,
green/yellow stripe, or
bare copper) coming from
the ceiling, downrod, and
hanging bracket.
Connect the black
(ungrounded) wire from
the ceiling to the black
wire from the fan.
Blue
Black
Green/Yellow Stripe
Green/Yellow Stripe
White
White
Ungrounded
Ungrounded (light)
Grounded
Grounded
Grounding
Grounding
G
r
e
e
n
/
Y
e
l
l
o
w
S
t
r
i
p
e
G
r
e
e
n
/
Y
e
l
l
o
w
S
t
r
i
p
e
x4
bag
x4
bag
Wire Nut
Wire Nut
Connect the black wire
(ungrounded) from the
ceiling to the black and the
blue wires from the fan.
Black
Blue
WARNING
All wiring must be in accordance with
national and local electrical codes ANSI/NFPA
70. If you are unfamiliar with wiring or in
doubt, consult a qualied electrician.
Installing the Downrod
Installing the Secondary Hanging System
Have extra wiring?
Turn the wires upward and push them carefully back through
the hanger bracket into the outlet box. Spread the wires apart,
with the grounded wires on one side of the outlet box and the
ungrounded wires on the other side of the outlet box. Make
sure that the wires are still attached to the wire nuts.
Hunter Pro Tip:
WARNING
The ceiling fan must be grounded. If the
ground wire for the installation site is not
present, immediately STOP installation and
consult a qualied electrician.

78
1886
1886
Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Glass/Bulbs
Canopy Screw
Installing the Bulbs and Glass
Installing the Canopy
Installing the Blades:
x15
x15
Insert washers found in the hardware bag into the
holes in the blades, then secure each blade to a blade iron
with screws found in the hardware bag.
Repeat x5
x2
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the hardware bag.
F
i
t
t
h
e
c
a
n
o
p
y
i
n
p
l
a
c
e
a
s
s
h
o
w
n
.
bag
bag
bag
Canopy Screw
Blade Screw
Blade Washer
Fan style may vary.
Note:
Assembling the Light
Repeat x5
x10
bag Blade Arm Screw
Lightly attach the blade arms to the motor with
screws found in the hardware bag, then
securely tighten after both screws are attached.
IMPORTANT
NOTE: The blade arms should be mounted with
the ridge facing downward. Installing it incorrectly
could result in your fan not functioning.
Ridge

78
1886
1886
Ceiling Bracket Downrod Hanging Fan Wiring Canopy Blades Light Glass/Bulbs
Canopy Screw
WARNING
GLASS FALL HAZARD
To prevent SERIOUS INJURY or DEATH, make
sure that glass is properly secured.
Installing the Bulbs and Glass
ON
Turn Power
Lift the globe and align the
notches in the globe with the
tabs in the light kit. Attach the
glass bowl to the light kit by
twisting it clockwise until it
snaps into place.
Repeat x2
Fan style may vary.
Note:
Partially install two light kit assembly
screws, found in the hardware bag,
halfway into the motor housing as shown.
It does not matter which two screw holes
you choose.
Feed the 9-pin plug connector coming from
the bottom of the motor housing through
the center hole in the light kit assembly.
Connect it to the plug connector found in
the switch housing area of the light kit
assembly. Make sure to line up the colored
markings on the connectors. Carefully push all switch housing components
into the switch housing, then install the switch
housing plate using two cover plate screws,
found in the hardware bag.
Install a bulb into each of the sockets.
When necessary, replace with bulbs of the
same type and wattage.
Align the keyhole slots in the top
of the light kit assembly with the
partially installed assembly screws.
Wrap the keyhole slots around the
screws and twist counterclockwise.
Insert a third light kit assembly screw,
found in the hardware bag, into place
and tighten all three screws securely.
1 of 3
Light Kit Screw
bag
2 of 3
Light Kit Screw
bag
1
STEP
4
STEP
2
STEP
3
STEP
Assembling the Light
WARNING
FAN FALL HAZARD
Make sure all three screws are tight to secure
the upper switch housing to the mounting plate.
WARNING
FAN FALL HAZARD
Make sure all three screws are tight to secure the
lower switch housing to the upper switch housing
5
STEP
2 of 2
Cover Plate
Screw
bag
Blade Arm Screw
Notch
Tab

910
1886
1886
Reversing the Fan
Reverse
Switch
Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise
rotation). To change the direction of air ow, turn the fan off and let it come to a complete stop.
The reversing switch is located inside the light xture. It can only be accessed when the glass is
removed. Slide the reversing switch to the opposite position. Restart the fan.
Updraft (clockwise rotation)
creates a more indirect airow.
Updraft airow is great for
moving warm air downward.
Downdraft (counterclockwise
rotation) creates a direct breeze
and maximum cooling effect.
Repeat x2
Remove and discard the plastic
connectors from the ends of the short
pull chains Connect the appropriate
pull chain pendant to each of the short
chains coming from the light kit. The
fan pull chain controls the speed: from
high to off. The light pull chain controls
the light xture: on and off. The fan pull chain controls
the speed: from high to off.
The light pull chain controls
the light xture: on and off.
Installing the Pull Chains