Hunter Hunter Ceiling Fan User manual

www.HunterFan.com 1.888.830.1326
PAGE
7
PAGE
10
PAGE
5
PAGE
6
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation Ceiling Bracket
Ladder
PAGE
3
Tools Needed
Wiring Canopy
Maintenance
& Cleaning Troubleshooting
DownrodPreparation
Table of Contents
PAGE
11
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or ofce for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
PAGE
4
Mounting Options
PAGE
18
?
?
?
PAGE
19
Remote Control
PAGE
16
PAGE
13
Blades Switch Housing
PAGE
12
Light Kit
PAGE
14
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
1
M3514-01 • 02/19/13 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
M3514-01 • 02/19/13 • © Hunter Fan Company
1.888.830.13261.888.830.1326
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
30 inches
from blade tip
to nearest wall
or obstruction 7 feet
from bottom
edge of blade
to the oor
Select a downrod length
Assess ceiling angle
Must be able to
secure the fan to
building structure or
fan-rated outlet box
1
2
3
Standard Downrod
for ceilings 8-10 feet high
Shorter Downrod
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet or higher
2
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS
w.1 - To reduce the risk of re, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage,
use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualied electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
This product may cause interference to radio equipment and
should not be installed near maritime safety communications
equipment, ships at sea, or other critical navigation or
communications equipment operating between 0.45-30 MHz.
This device complies with Part 18 of the FCC Rules.

www.HunterFan.com 1.888.830.1326
Tools Needed
Ladder
Power Drill
(optional)
9/64” Drill Bit
(optional)
Screwdrivers
Pliers Wire Strippers
If mounting to a support structure, you will also need these tools.
3
M3514-01 • 02/19/13 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
4
M3514-01 • 02/19/13 • © Hunter Fan Company
1.866.268.1936
If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Guide Touches
BOTH Ceiling & Wall
S
I
T
U
A
T
I
O
N
1
Guide Touches Wall
but NOT Ceiling
S
I
T
U
A
T
I
O
N
2
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
Downrod
*most common
If you have a at ceiling:
Hang your fan by a standard downrod (included).
Mounting Options
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
4
34OCEILING
WALL
OPTION
1
Standard
Mounting
OPTION 2
Angled
Mounting
2 3
SLIDE
toward ceiling
PLACE
against wall
1
FOLD
on dotted line
34°
Use the three steps below to determine if your ceiling angle is greater than 34°
Support
Structure
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Standard
Mounting
Style
Support
Structure
Ceiling
Outlet Box
(required)
M3514-01 • 02/19/13 • © Hunter Fan Company
www.HunterFan.com

1.888.830.1326
www.HunterFan.com
Ceiling Bracket
OFF
Make sure all four (4) bumpers
are still attached.
For angled ceilings, point
opening toward peak.
Refer to warning w.1 on pg. 2
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
Turn Power
5
M3514-01 • 02/19/13 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Ceiling Bracket (continued) Preparation 1.888.830.1326
www.HunterFan.com
D
I
S
C
A
R
D
K
E
E
P
!
Remove the shipping blocks from the
motor. Save the screws. They will be
needed for blade iron installation.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and save the screws.
Time Saver Tip: Get a helper
to insert grommets, found in
the hardware bag, into the
blades while you’re doing the
next couple of steps.
6
M3514-01 • 02/19/13 • © Hunter Fan Company

1.888.830.1326
Downrod
Slide
Slide
1 2 3 4 5
678910
Sold Separately
Included
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Standard
Downrod
for ceilings 8-10’ high
Option 1Option 2
Option 3
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Steps 6-10 to reassemble with new pipe
Included (pre-assembled)
www.HunterFan.com
7
M3514-01 • 02/19/13 • © Hunter Fan Company

KEEP!
8”
3/8”
C
U
T
&
S
T
R
I
P
(not to scale)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Downrod (continued)
8” 3/8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
If the setscrew is not tightened
securely, the fan may fall.
K
E
E
P
!
1.888.830.1326
www.HunterFan.com
8
M3514-01 • 02/19/13 • © Hunter Fan Company

1.888.830.1326
9
M3514-01 • 02/19/13 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.

www.HunterFan.com 1.888.830.1326
Wiring
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
B
R
A
C
K
E
T
green/yellow stripe (grounding)
green/yellow stripe
green/yellow stripe
Using an orange wire connector
from the hardware bag, connect
the black wire (ungrounded) from
the ceiling to the black wire from
the receiver. Connect the white wire
(grounded) from the ceiling to
the white wire from the receiver.
F
R
O
M
F
A
N
F
R
O
M
F
A
N
F
R
O
M
C
E
I
L
I
N
G
black (ungrounded) white (grounded) white
black
Using an orange wire connector
from the hardware bag,
connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and hanging bracket.
10
M3514-01 • 02/19/13 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
11
M3514-01 • 02/19/13 • © Hunter Fan Company
Canopy
Lift the canopy into place so that
the screw holes are aligned.
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Screw
Holes
Insert the two canopy screws
found in the hardware bag.
Note: Fan style may vary.

www.HunterFan.com 1.888.830.1326
M3514-01 • 02/19/13 • © Hunter Fan Company
Blades
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the nishes.
12
Insert grommets found in the hardware
bag into the holes in the blades, then
secure each blade to a blade iron with
screws found in the hardware bag.
Remember the screws that
you kept after removing the
shipping blocks (page 6)? You
need them for this step.
Lightly attach the blade irons to the
motor with the blade iron armature
screws, then securely tighten after both
screws are attached.

www.HunterFan.com 1.888.830.1326
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Screw two (2) housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Insert the third screw, found in
the hardware bag, into place and then
tighten all three (3) screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing xture falling.
Switch Housing
13
M3514-01 • 02/19/13 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Light Kit
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light xture falling.
Lift the lower switch housing up until its
screw holes are aligned with the screw holes
in the upper switch housing.
Install the three switch housing screws
found in the hardware bag.
Connect the plugs from the upper and
lower switch housings. Make sure to line up
the colored markings on the connectors.
Screw
Holes
14
M3514-01 • 02/19/13 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
Light Kit (continued)
CONGRATULATIONS!
YOU’RE DONE!
See next page for fan
operation instructions.
Place the glass bowl over the heater vent,
ensuring the threaded portion of the heater
vent comes out of the bottom of the glass
bowl. Place the nial over the threaded
portion of the heater vent and twist it to
tighten it against the glass bowl.
Install a light bulb in each socket.
Note: Do not use CFL bulbs to replace your light
bulbs. Your lights may icker or fail to work.
Finial
Note: Globe style and number of
lights may vary.
Note: In compliance with US federal energy regulations, this ceiling fan
contains a device that restricts its light output. Exceeding the wattage
limit marked on the MAX wattage sticker afxed to the light socket(s)
may result in re hazard or improper operation.
Glass Bowl
Threaded
Portion
of Heater
Vent
M3514-01 • 02/19/13 • © Hunter Fan Company
15

www.HunterFan.com 1.888.830.1326
To install the transmitter cradle, remove
the two screws holding the switch
cover plate. Do not remove the cover
plate. Orient the cradle by lining up
the two mounting holes with those on
the cover plate. Insert and tighten the
screws. Do not over tighten. Note: For
rocker-style cover plates, break off the
tabs by pushing outward.
Rocker-
Style
Plate
Switch
Cover
Plate
Removed
Tabs
Remote Control
Install one (1) 12-Volt, type 23A, MN-21
battery (included) into the transmitter.
Clean the battery contacts and also
those of the device prior to battery
installation. Ensure the battery is
installed correctly with regard to
polarity (+ and -). Please contact your
local battery recycling center for proper
battery disposal information.
Setting the DIP switches:
You will only have to change the DIP switch settings in the
remote if you are using more than one remote controlled fan
in the same area and want to control them separately. You may
want to label your remotes to ensure you do not mix them up.
1. At the circuit breaker or fuse box, turn the power off for
the fan you want to change. Do not turn the power off at the
circuit breaker for the previously installed fan, as you may
inadvertently change the DIP switch code settings for it as well.
2. Slide the cover off the back of the remote and remove the
battery. The battery must be removed when changing DIP
switch settings.
3. Change the DIP switch settings, so that they are different
from the previously installed fan.
4. Replace the battery and cover.
5. At the circuit breaker or fuse box, turn the power back on for
the fan whose settings you are changing.
6. Within 20 seconds of restoring power, push the 3 (high), 2
(medium), and 1 (low) buttons (in that order) on the remote.
Note: The receiver (built into the fan) has a memory function
that retains the last DIP switch code setting. The setting will not
change in the event of power failure or if the power to the fan is
inadvertently shut off.
+ –
DIP
switches
16
M3514-01 • 02/19/13 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
CAUTION:
• Always purchase the correct size and
grade of battery most suitable for the
intended use.
• Clean the battery contacts and also those
of the device prior to battery installation.
• Ensure the batteries are installed
correctly with regard to polarity (+ and -).
• Remove batteries from equipment which is
not to be used for an extended period of time.
• Remove used batteries promptly.
Auto Resume Feature
This fan contains a receiver with an auto resume
feature. The receiver remembers the intensity of the
light, speed and direction of the fan, and whether
the heater is on or off. When power is restored to
the receiver, the fan, light, and heater will be at the
previous settings.
Fan Operation:
To start the fan, press the speed button on the remote
at the level you desire:
• 3 for high
• 2 for medium
• 1 for low
To turn off the fan, press 0.
Light Operation:
The light button is used to turn on, dim, and turn off
the light.
To Turn the light on:
• Press the light button 1 time and the light will
come on to the previously set level.
To dim the light:
• Press and hold the light button until the light has
reached the desired level. (As you hold the button,
the light level will move throughout its entire
range within 16 seconds.) Release the button at the
desired level.
To Turn the light off:
• Press the light button 1 time for gradual off and
the light will dim automatically for approximately
20 seconds until all the way off to allow for safe exit
from the room.
• Press the light button 2 times or 1 time while the
light is dimming for instant off.
Heater Operation:
The heater button is used to turn on, and off the
heater.
• Press the heater button 1 time to turn the
heater on.
• Press the heater button again to turn the
heater off.
Note: Regardless of the speed setting on the fan,
when the ceiling fan is operating and the heater
function is turned ON, the ceiling fan automatically
switches to low-speed updraft only and will not
accept any commands from the remote until the
heater is turned off.
HeaterLight
Reverse Switch
Remote Control (continued)
17
M3514-01 • 02/19/13 • © Hunter Fan Company

www.HunterFan.com 1.888.830.1326
M3514-01 • 02/19/13 • © Hunter Fan Company
18
Maintenance & Cleaning
ON
Turn Power
Changing the bulbs - unscrew the
nial and remove it from the heater
vent while supporting the glass
bowl with your other hand. Carefully
remove the glass bowl. Unscrew
bulbs and replace with bulbs of same
type and wattage. Reinstall the glass
bowl assembly.
Changing the direction of air
ow - press the reverse switch.
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the nishes.
Reverse Switch
Finial
Glass Bowl
Threaded
Portion
of Heater
Vent

www.HunterFan.com 1.888.830.1326
M3514-01 • 02/19/13 • © Hunter Fan Company
19
Troubleshooting
Excessive wobbling
• Tighten all of the blade and
blade iron screws until they
are snug.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Use the provided balancing
kit and instructions to balance
the fan.
Noisy Operation
• Tighten the blade and blade
iron screws until they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
Fan doesn’t work
• Make sure power switch is on.
• Pull the pull chain to make sure
it is on.
• Push the motor reversing switch
rmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 10.
• Check the plug connection in
the switch housing.
Lights dim when turned on or
do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specications on the light
sockets.