Hunter Professional Series Guide

®
®
Fig. 1
®
ARC ADJUSTMENTS
Adjustable heads are preset to approximately 180°.
Sprinklers may be adjusted with water on or off. It is
recommended that initial adjustment be made
before installation.
1. Using the palm of your hand, rotate the
nozzle turret counterclockwise to the left stop
to complete any interrupted rotation cycle
(Fig. 1).
2. Rotate the nozzle turret clockwise to the right
stop. This is the fixed side of the arc. The
nozzle turret must be held in this position for
all arc adjustments.
To Increase the Arc:
1. Insert the key end of the Hunter wrench into
the adjustment socket (Figs. 2 & 3).
Insert the key end of the Hunter wrench
into the lifting socket of the sprinkler. Pull the
riser up to gain access to the nozzle socket.
Using the Hunter wrench, loosen the
nozzle/range-adjustment screw. If a nozzle
is already installed in the sprinkler, it can be
removed by briefly turning on the water, or
by pulling on one of the nozzle “ears” with
needle-nose pliers.
Slip the desired nozzle into the nozzle
socket. Note that the socket is angled up
25°. Also note that the “ears” should be
located at the top (Fig. 4). Tighten the
nozzle/range-adjustment screw.
1.
2.
3.
NOZZLE INSTALLATIONRADIUS ADJUSTMENT
Insert the hex end of the Hunter wrench into
the nozzle/range-adjustment screw (Figs. 2 &
3). Turn the screw clockwise (into the stream
of water) to decrease the radius, or
counterclockwise to increase the radius.
PRECIPITATION RATE ADJUSTMENT
For excessively wet or dry areas, the
precipitation rate can be adjusted—simply
replace the existing nozzle with a larger one to
increase, or a smaller one to decrease, the rate
of precipitation.
Note: It is not necessary to disassemble
the sprinkler to make adjustments.
®
Professional Series
PGP, PGS, PGH
Gear-Driven Sprinklers
2. While holding the nozzle turret at the right stop,
turn the wrench clockwise. Each full turn of the
wrench increases the arc 90°.
3. Adjust to any arc between 40°and 360°.
4. Wrench will stop turning or there will be a
ratcheting noise, when the maximum arc (360°)
is reached.
To Decrease the Arc:
1. Insert the key end of the Hunter wrench into the
adjustment socket (Figs. 2 & 3).
2. While holding the nozzle turret at the right stop,
turn the wrench counterclockwise. Each full
turn of the wrench decreases the arc 90°.
3. Adjust to any arc between 40°and 360°.
4. Wrench will stop turning, or there will be a
ratcheting noise, when the minimum arc (40°)
is reached.
Fig. 4
Fig. 2
Fig. 3
Nozzle/Range-
Adjustment
Screw
Lifting
Socket
Adjustment
Socket
Nozzle
Turret Nozzle
Socket
ID Button
Hunter Industries Incorporated • The Irrigation Innovators © 2001 Hunter Industries Incorporated
U.S.A.: 1940 Diamond Street • San Marcos, California 92069 • TEL: [phone] • FAX: [phone] • www.HunterIndustries.com P/N 700026
Australia: 8 The Parade West • Kent Town, S. Australia 5067 • TEL: [phone] • FAX: [phone] INT-026.PDF
Europe: Europarc, Bât. B14 • 1330, rue G. de la Lauzières • 13855 Aix-en-Provence, France • TEL: [phone] • FAX: [phone]

7
8
9
10
11
12
1
2
3
4
5
6
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,8
3,4
4,1
4,8
2,8
3,4
4,1
4,8
2,8
3,4
4,1
4,8
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
275
344
413
482
275
344
413
482
275
344
413
482
0,11
0,14
0,16
0,18
0,16
0,18
0,20
0,23
0,20
0,23
0,27
0,30
0,27
0,32
0,36
0,41
0,36
0,41
0,45
0,50
0,45
0,55
0,61
0,66
0,59
0,68
0,77
0,84
0,73
0,84
0,95
1,04
0,95
1,11
1,25
1,36
1,36
1,54
1,73
1,86
1,82
2,02
2,23
2,39
2,59
2,77
3,00
3,27
1,9
2,3
2,7
3,0
2,6
3,0
3,4
3,8
3,4
3,8
4,5
4,9
4,5
5,3
6,1
6,8
6,1
6,8
7,6
8,3
7,6
9,1
10,2
11,0
9,8
11,4
12,9
14,0
12,1
14,0
15,9
17,4
15,9
18,5
20,8
22,7
22,7
25,7
28,8
31,0
30,3
33,7
37,1
39,7
43,2
46,2
50,0
54,5
8,5
8,8
8,8
9,1
8,8
9,1
9,1
9,4
9,1
9,4
9,4
9,8
9,8
10,1
10,4
10,4
10,4
11,0
11,6
11,6
11,0
11,6
12,2
12,2
11,0
12,2
12,8
12,8
11,3
12,2
13,1
13,4
11,6
13,1
14,0
14,3
13,7
14,6
14,9
15,5
14,0
14,6
15,2
15,5
14,0
14,6
15,2
15,9
Nozzle
m
3
/hr.
kPaBars l/min
Radius
m
Pressure
Flow
Performance Data
Matched Precipitation
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
206
275
344
413
275
344
413
482
0,32
0,39
0,41
0,45
0,36
0,43
0,48
0,52
0,48
0,57
0,64
0,68
0,64
0,70
0,80
0,86
0,77
0,89
1,00
1,07
0,98
1,14
1,27
1,39
1,48
1,66
1,82
1,95
5,3
6,4
6,8
7,6
6,1
7,2
7,9
8,7
7,9
9,5
10,6
11,4
10,6
11,7
13,2
14,4
12,9
14,8
16,7
17,8
16,3
18,9
21,2
23,1
24,6
27,6
30,3
32,6
6,7
7,3
7,9
8,5
7,6
8,2
8,5
9,1
8,2
9,1
10,1
10,7
8,8
9,8
10,7
11,3
9,4
10,4
11,3
11,6
10,1
11,3
12,2
12,8
11,6
12,2
12,8
13,4
8
9
10
P
4
7
5
6
Blank nozzle plug for turning off
selected sprinklers during repairs,
maintenance, etc.
m3/hr.
kPaBars l/min
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,1
2,8
3,4
4,1
2,8
3,4
4,1
4,8
m
3
/hr. l/min
Flow m
3
/hr. l/min
Flow
90°
Nozzle #
180°
Nozzle # 360°
Nozzle #
m
3
/hr. l/min
Flow
PGS, PGP, PGH Performance Chart PGS, PGP, PGH Low Angle Chart
Nozzle
Radius
m
Pressure Flow
Square
Spacing
When the spacing/arc/nozzle pressure combinations are spaced as indicated, the precipitation rate
will be approximately 10 mm/hr. at 3,4 bars/344 kPa.
1 0 mm/hr at 3,4 bars/344 kPa
1
2
3
4
5
0,16
0,20
0,27
0,36
0,45
2,7
3,4
4,5
6,1
7,6
4
5
6
7
8
6
8
9
10
11
7,6 m
9,1 m
10,7 m
12,2 m
13,7 m
0,77
0,95
1,25
1,73
2,23
12,9
15,9
20,8
28,8
37,1
0,36
0,45
0,61
0,77
0,95
6,1
7,6
10,2
12,9
15,9