Reliable F1FR-300 User manual

103 Fairview Park Drive, Elmsford, New York 10523
Bulletin 164 Rev.B
Model F1FR-300/CCP
300 psi (20,7 bar) Rated
Concealed Quick
Response Sprinkler
Product Description
The Reliable Model F1FR-300/CCP Quick Response
Concealed Sprinkler is an attractive, low profile concealed
sprinkler assembly. This sprinkler assembly utilizes a
Model F1FR-300 pendent sprinkler in a Model CCP cup
and cover plate assembly. The cup is securely factory
threaded on the sprinkler inlet end. The assembly is
shipped with a protective cap. The sprinkler and cup are
easily installed into the drop nipple using the Model RC1
Sprinkler Wrench. The cover plate assembly is attached to
the sprinkler cup using a cover plate assembly with flexible
tabs for threaded engagement. Simply push on the cover
plate, then turn to adjust or remove the cover plate
assembly.
The cover plate is attached to the skirt using 135°F
(57°C) or 165°F(74°C) ordinary temperature classification
solder. When the ceiling temperature rises, the solder
holding the cover plate melts, allowing the release of this
part and thus exposing the Model F1FR-300 sprinkler
inside to the rising ambient temperature.
The Model F1FR-300 automatic sprinkler utilizes a
3.0mm frangible glass bulb. This sprinkler has
demonstrated response times in laboratory tests which are
five times faster than standard responses sprinklers. This
quick response enables the Model F1FR-300 sprinkler to
apply water to a fire sooner than standard sprinklers of the
same temperature rating.
The glass bulb consists of an accurately controlled
amount of special fluid hermetically sealed inside a
precisely manufactured glass capsule constructed to
provide fast thermal response. The other sprinkler parts
are made of brass, copper and beryllium nickel.
At normal temperatures, the glass bulb contains the
fluid in both the liquid phase and vapor phase. The vapor
phase can be seen as a small bubble. As heat is applied
the liquid expands, forcing the bubble smaller and smaller
as the liquid pressure increases. Continued heating
forces the liquid to push out against the bulb causing the
glass to shatter, opening the waterway and allowing the
deflector to distribute water.
The temperature rating of the sprinkler is identified by
the color of the glass bulb.
Application and Installation
The Model F1FR-300/CCP Concealed Sprinkler
Assembly uses a ½²(15mm) orifice, ½²NPT (R½), 135°F
(57°C), 155°F(68°C), 175°F(79°C), or 200°F(93°C) rated
Model F1FR-300 Pendent Sprinkler with a threaded Model
CCP cup, which is factory attached to the sprinkler. The
assembly is completed by the installation of an attractive,
low profile, 135°F(57°C) or 165°F(74°C) rated Model CCP
push on cover plate assembly. The cover plate and
sprinkler cup assemblies are joined using a cover plate
with flexible tabs for threaded engagement. A choice of
Bulletin164
Rev.
B
Features:
1. 300 psi (20,7 bar) rated.
2. Quick response performance.
3. Push on, thread off, sturdy, convenient
cover plate.
4. Factory assembled sprinkler and cup,
shipped complete with protective cap.
5. Sprinkler assembly and cover plate
separately packaged.
6. Two versions:
•½" (13mm) Adjustment.
•516"(8mm) Adjustment.
7. Rugged damage resistant assembly.
No exposed thermal element.
8. Utilizes Model F1FR-300 Pendent
Sprinkler.
9. Aesthetic ceiling profile.
10. Available in white or other color
painted; or brass, chrome or black
plated finishes.
Listings and Approvals
1. Underwriters Laboratories, Inc.
2. UL Certified for Canada.
3. NYC MEA 258-93-E
UL Listing Category
Sprinklers, Automatic and Open
-Quick Response Concealed.

The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory
Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.
Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highly
qualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries.
The Reliable Automatic Sprinkler Co., Inc.
[phone] Sales Offices
[phone] Sales Fax
[phone] Corporate Offices
www.reliablesprinkler.com Internet Address
Revision lines indicate updated or new data.
E.G. Printed in USA 08/04 P/N 9999970168
Recycled
Paper
Manufactured by
concealed cover plate assembly on any sprinkler with
which it is not specifically listed may prevent good fire
protection and will void all guarantees, warranties, listings
and approvals.
Maintenance
Model F1FR-300/CCP Concealed Sprinklers should be
inspected quarterly and the sprinkler system maintained in
accordance with NFPA 25. Do not clean sprinklers with
soap and water, ammonia or any other cleaning fluids.
Remove dust by using a soft brush or gentle vacuuming.
Remove any sprinkler cover plate assembly which has
been painted (other than factory applied) or damaged in
any way. A stock of spare sprinklers should be maintained
to allow quick replacement of damaged or operated
sprinklers. Prior to installation, sprinklers should be
maintained in the original cartons and packaging until
used to minimize the potential for damage to sprinklers
that would cause improper operation or non-operation.
two cover plate assemblies provide either ½" (13mm) or
516" (8mm) of cover adjustment.
Do not install these sprinklers in ceiling which have
positive pressure in the space above.
After a 258" (67mm) diameter hole is cut in the ceiling,
the sprinkler is easily installed with the Model RC1 Wrench.
A Teflon*-based thread sealant should be applied to the
sprinkler threads only. The Model RC1 Wrench is then
used to engage the sprinkler wrenching surfaces and to
install the sprinkler in the fitting. When inserting or
removing the wrench from the sprinkler/cup assembly, DO
NOT WRENCH ON ANY OTHER PART OF THE
SPRINKLER. The cover plate is then pushed onto the cup.
Final adjustment is made by hand turning the cover plate
until the skirt flange makes full contact with the ceiling.
Cover plate removal requires turning in the counter
clockwise direction.
After installation, inspect all sprinklers to ensure that
there is a gap between the cover plate and ceiling and that
the four cup slots are open and free from any air flow
impediment to the space above.
Concealed cover plate/cup assemblies are listed only
for use on specific sprinklers. The use of any other
concealed cover plate/cup assembly with the Model
F1FR-300 Pendent Sprinkler or the use of the Model CCP
Nominal
Orifice Size Thread Size
Nominal
K Factor Temp. Rating Max.
Ambient
Temp. Bulb Color
Sprinkler
Identification
Number (SIN)US Metric Sprinkler Cover
½²(15mm) ½²NPT (R½) 5.6 80 135°F/57°C 135°F/57°C 100°F/38°COrange
R5615
½²(15mm) ½²NPT (R½) 5.6 80 155°F/68°C 135°F/57°C 100°F/38°CRed
½²(15mm) ½²NPT (R½) 5.6 80 175°F/79°C 165°F/74°C 150°F/66°CYellow
½²(15mm) ½²NPT (R½) 5.6 80 200°F/93°C 165°F/74°C 150°F/66°CGreen
8. Cover Plate Temp Rating:
9. 135°F(57°C) for 135°F and
155°F Spks; 165°F(74°C) for
175°F and 200°F Spks.
10.Cover plate adjustment:
Either ½²(13mm) or 516²(8mm)
(approximate adjustment).
11.Cover Plate Finish.
Standard Finishes
Chrome
White Paint
Special Application Finishes
Bright Brass
Black Plating
Black Paint
Off White
Satin Chrome
Cover Plate Finishes (1)
(1)Other colors and finishes
are available. Consult
factory for details.
Figure 1 Figure 2
*DuPont Registered Trademark
Technical Data
Ordering Information
Specify:
1. Sprinkler Model F1FR-300
½²Orifice (15mm),
2. ½²NPT (R½).
3. Sprinkler Temp. Rating:
4. 135°F(57°C), 155°F(68°C),
5. 175°F(79°C), 200°F(93°C).
6. Cover Plate: Model CCP.
7. Sprinkler Cup Thread Size:
½²NPT (R½).
Installation Wrench
Model RC1 Sprinkler Wrench
Installation Aid
A protective cap is included
for use during installation.