Hurley Marine DINGHY CHOCK User manual
WARNINGS
WARNING - Failure to install, maintain, protect, and operate the system properly can cause
malfunction resulting in possible serious or fatal injuries and/or property damage.
WARNING - Chock system is not intended to be used with any person(s) and/or possessions in
the dinghy.
WARNING - Chock should not be placed in an area where it may come in contact with
mechanical parts.
WARNING - Remove drain plug from tender when on Chock.
WARNING - A dinghy cover is recommended to keep water from entering the dinghy.
WARNING - Do not drill holes in your Chock or alter in any way.
WARNING - Only use stainless steel hardware when mounting and use a backing plate when
applicable.
WARNING - Dinghy must be secured/tied down before transporting.
WARNING - Regular inspection, adjustment, and maintaining your davit and other
associated components is necessary to ensure proper operation.
WARNING - Always clean the davit system with fresh water when it is used in a corrosive
environment to maintain longevity. Annually use a Rust & Corrosion protectant
on your stainless steel. Fluid Film is suggested.
CAUTION: - It is suggested to off-set the Chock, during installation, on the platform so that the
stern of the dinghy is more supported due to weight of motor, etc.
CAUTION - Weight limit: 725 pound safe working load limit. Do not exceed weight load limit.
Your Hurley Chock system is made of Marine Grade High Density Polyethylene Cradles and Stainless
Steel components and hardware. This Chock system allows scuff-free maneuvering of your tender.
The chocks can be positioned, or removed, in the multiple holes provided for the best position for
your tenders hull. For soft bottom dinghies, you may want to remove the chocks.
Planning the installation - Rail / Channel Install:
Make sure the Chocks are properly aligned and in place before securing. If
using the knobs for rail installs, only hand tighten.
Note: An additional bolt, nut & washer, or other means should be used as stopper
in the rail or channel as so it doesn’t slid out.
Planning the installation - Deck Plate Install:
You may want to off-set the Chock depending on your dinghies weight distribution. Of course this
depends on many factors, including, but not limited to, the beam of your boat, length of your
dinghy and any obstructions. Distance between cradles should be no less than 36” and dependant
upon the length of your tender.
After determining where to place your
Chocks start with a small drill bit and increase
bit size to 3/4”. The three holes should be
drilled for the screws that are included. It is
good practice to use tape on the surface to be
drilled then drill the hole through the tape,
this will avoid scratching/chipping of the
surrounding surface. Generously apply 3M
5200 sealant to seal drilled holes and the
bottom of the decking plates. Measure
twice, drill once!
Tie downs must be used when underway!
Hurley Marine, Inc. • 2717 N. Lincoln Road • Escanaba, MI 49829 USA
LIMITED WARRANTY AND LIMITATION OF LIABILITY
All new products manufactured under Hurley Marine, Inc., are warranted to be free from defects in material and
workmanship under normal and proper use for a period of (2) two years from date of shipment from Hurley Marine, Inc. No
claim for breach of warranty will be allowed unless the material or workmanship is found defective within the warranty
period, properly documented by buyer and Hurley Marine, Inc. is notified in writing within 10 days from failure. This
warranty shall not apply to products that have been disassembled, altered, or utilized in a manner not approved by Hurley
Marine, Inc. or subjected to normal wear and tear, abuse, misuse, improper maintenance, negligence or accident.
CUSTOMER AGREES THAT USE OF THE PRODUCT/SERVICE IS ENTIRELY AT CUSTOMER'S OWN RISK. THE
FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE ACCEPTED BY BUYER IN LIEU OF ANY AND ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. Buyer’s sole remedy in the event of a breach of the
forgoing warranties is the repair or replacement of the affected product by Hurley Marine, Inc., upon the return of the
product transportation charges prepaid to Hurley Marine, Inc., and after a charge to buyer for the use of the product prior
to its return. BUYER AGREES THAT IN NO EVENT WILL HURLEY MARINE, INC’S LIABILITY FOR ALL LOSSES
FROM ANY CAUSE, WHETHER BASED ON CONTRACT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR
OTHERWISE, EXCEED BUYER’S NET PURCHASE PRICE, NOR WILL HURLEY MARINE, INC, BE LIABLE FOR ANY
SPECIAL, INCIDENTAL CONSEQUENTIAL OR EXEMPLARY DAMAGES.
Under no circumstances is Hurley Marine, Inc. responsible for reimbursement of expenses related to vessel haul-outs,
technician or yard personnel, travel expenses, yacht storage, labor performed during removal and/or replacement of
fixture(s), or shipping costs for replacement parts and/or repairs. These are assumed liabilities of the customer and part of
the terms of sale between Hurley Marine, Inc. and its customer.
The foregoing warranties will continue in effect for so long as the product is serviced and maintained in accordance with
Hurley Marine, Inc. instructions and with genuine Hurley Marine, Inc. manufactured replacement parts. These warranties
may not be altered or amended except by a written instrument signed by buyer and a duly authorized officer of Hurley
Marine, Inc. For warranty or service assistance contact your Hurley Marine, Inc. dealer.
TERMS OF SALE / SHIPPING
RETURN POLICY: If you are dissatisfied with your purchase, contact us within 30 days from the date of product purchase.
Products returned within 30 days of their receipt, unopened in their original packaging and otherwise in new condition will
automatically be exchanged or refunded. A minimum fee of 25% of the price of the product will be charged for inspection,
repacking and restocking for items not returned in their original condition. Other fees may apply depending upon the
condition of the item. Products are not returnable after 30 days.
EXCHANGE / REFUND PROCEDURE:
• All returns must have a Return Authorization number. Contact place of purchase for a Return Authorization number.
• Properly repack the product in the original packaging and place inside a box suitable for shipping with all the original
enclosures, parts, and accessories.
• The Return Authorization number must be on the box next to the shipping address.
• Return it with original receipt and postage pre-paid (we do not accept C.O.D.), add appropriate insurance.
• Shipping and packing fees are non-refundable.
Non-Returnable items: Inflatable boats, installed/mounted items, damaged goods, clearance/discount items, used and/or
display items, electrical goods, light bulbs and special ordered items are not returnable, unless defective, and then for
repair/replacement only. If the product is defective you must call Hurley Marine, Inc. within 10 days of receipt of the product.
DAMAGES GOODS: We thoroughly inspect all items prior to shipment. We suggest that you also thoroughly inspect the
item(s) before accepting delivery. If damage is apparent, refuse delivery or if your parcel is left without a signature and
damage is found contact the carrier immediately. Do not discard the box or any packaging materials. Most claims must be
filed with the carrier within 10 days of receipt of delivery. Although we take special care to ensure the safe arrival of your
merchandise, our responsibility for damage ends when the carrier accepts shipment.
Table of contents
Other Hurley Marine Marine Equipment manuals
