Husky Flair User manual

EN
2000868
conformé à / conformed to ULSTD 1017
certifié / certified
CAN/CSA STD C22.2 No. 243-M91
DOC-530 REV01
CENTRAL VACUUM SYSTEM
USER MANUAL
THIS MANUAL APPLIES TO:
Husky flair

2 | EN DOC-530_EN REV01
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS�������������������������������������������������������������������������������������������������������������������� 3
2. GENERAL GUIDELINES & REFERENCE ������������������������������������������������������������������������������������������������������������������ 4
GROUNDING REQUIREMENTS
SOME GENERAL GUIDELINES TO BE RESPECTED AT ALL TIMES
3. MODELS���������������������������������������������������������������������������������������������������������������������������������������������������������������������� 5
4. INSTALLATION ���������������������������������������������������������������������������������������������������������������������������������������������������������� 5
POWER UNIT
5. THE HOSE HANDLE �������������������������������������������������������������������������������������������������������������������������������������������������� 6
6. LOW VOLTAGE TECHNOLOGY SYSTEM ���������������������������������������������������������������������������������������������������������������� 6
INSTALLATION
OPERATING INSTRUCTIONS
7. SYSTEM OPERATING INSTRUCTIONS������������������������������������������������������������������������������������������������������������������� 6
8. SYSTEM MAINTENANCE ������������������������������������������������������������������������������������������������������������������������������������������ 6
MOTOR
HANDLE
9. TROUBLESHOOTING ����������������������������������������������������������������������������������������������������������������������������������������������� 8
GENERAL
LED INTERPRETATION GUIDE
10. CONTACT������������������������������������������������������������������������������������������������������������������������������������������������������������������ 8
11. RECYCLING INSTRUCTIONS ��������������������������������������������������������������������������������������������������������������������������������� 8

3 | EN DOC-530_EN REV01
READ ALL INSTRUCTIONS BEFORE USING THIS CENTRAL VACUUM SYSTEM
When using an electrical appliance, basic precautions should always be followed.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
• Unplug and disconnect the power unit from the electrical outlet before servicing or maintenance.
• Do not install outdoors and do not use on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended accessories.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or
dropped into water, return it to a service centre.
• Do not pull or carry by power cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
• Check inlet openings for small objects that may not have been vacuumed in order to keep openings clear of air flow reducing factors.
• Keep power cord away from heated surfaces.
• Do not unplug by pulling on power cord. To unplug, grasp the plug, not the cord.
• Do not handle system or accessories with wet hands.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
IMPORTANT: DO NOT vacuum gypsum dust, flour, mud or any equivalent substances because they cake onto the filter
and obstruct the filtration system. This can cause the motor to overheat and hinder the proper functioning of the unit. The
power unit must always have the permanent filter installed.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
• Connect to a properly grounded outlet only. See grounding requirements in section 2.
• Do not exhaust into a wall, a ceiling or concealed space of a building or structure, use appropriate installation to exhaust outside the
residence.
• Make sure that the air exhaust is never obstructed.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not place or store anything on top or around of the power unit, overheating of motor could occur.
SAVE THESE INSTRUCTIONS
INTENDED FOR HOUSEHOLD USE ONLY
1. IMPORTANT SAFETY INSTRUCTIONS

4 | EN DOC-530_EN REV01
GROUNDING REQUIREMENTS
These appliances must be grounded. If they should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. These appliances have a
power cord of 5.4ft / 1.65m in length and are equipped with a grounding conductor and grounding
plug. The plug must always be inserted directly into an electrical outlet that is properly installed and
grounded in accordance with all local codes and regulations.
DO NOT USE AN EXTENSION CORD.
WARNING:
Improper connection of the equipment grounding conductor can
result in a risk of electric shock. Check with a qualified electrician
or service person if you are in doubt as to whether the outlet
is properly grounded. Do not modify the plug provided with
the appliance – if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This appliance is for use on a nominal circuit of 15A at 110-120
Volts C. A., 50/60 Hz. The unit has a grounding attachment plug.
Make sure that the appliance is connected to an outlet having
the same configuration as the plug. No adapter should be used
with this appliance. The power unit should be connected to an
independent circuit breaker.
SOME GENERAL GUIDELINES TO BE RESPECTED AT ALL TIMES
1� The power unit must be installed in a ventilated area away from any
heat source;
2� The Husky central vacuum system must be used only on dry surfaces. At
no time should the system be used to draw up liquids nor should it be
used to vacuum wet carpets or floors.
3� It is mandatory that the filtration grid be equipped with its permanent
filter at all times when the system is in use;
4� The motor housing must never be obstructed in any way to avoid
overheating or damaging;
5� DO NOT vacuum gypsum dust, flour, mud, or any sludgy materials as
they cake onto the filter and obstruct the filtration system resulting in the
over-heating of the motor and thus failure of the power unit to function
properly;
6� Do not attempt to shorten or modify the electrical power cord;
7� As a security measure, unplug the electrical power cord before proceeding
with any maintenance;
8� In order for the warranty to be valid, only a Husky authorised service
personnel may carry out the necessary repairs or maintenance on the
motor;
9� The warranty will be void if non-recommended products such as filters
or any other after-sale parts as carbon brushes and motors are used to
repair the unit. Husky recommends strongly to use only Husky certified
filters and replacement parts.
10� Appliance must be so positioned that the plug is always easily accessible.
11� Pertaining to an electrified inlet valve (intended for the connection of a
current-carrying hose/motorized nozzle combination):
• Connect only a current-carrying hose to this wall valve;
• Do not install a wall valve outdoors;
• Do not use with a damaged hose. Return hose to a service centre;
IMPORTANT
Husky is not responsible for damages resulting from improper
use. The warranty does not cover damage resulting from misuse
or problems resulting from installation that does not conform
to specifications, or any functional alterations and / or physical
changes to the power unit. Improper or non-recommended
installation of the system and / or power unit done against
predefined principles of the user manual is also considered
misuse.
All conditions and restrictions are set forth in the Nuera limited
warranty, the user manual and the system installation guide. To
optimize the performance and life of your Husky power unit, it is
important to do regular maintenance and cleaning of the filter
according to the guidelines listed in this user manual.
2. GENERAL GUIDELINES & REFERENCE

5 | EN DOC-530_EN REV01
Fig.1 Shown: flex, available in low voltage and basic wireless technologies
NOTE
»APPLICABLE TO ALL POWER UNITS: in order to avoid
overheating, we recommend 12in / 30cm clearance all around
the power unit.
3. MODELS
POWER UNIT
Fig.2 Mounting the flair on the wall.
The power unit must be installed in a ventilated area, easily accessible and away from any heat source.
It should also be close to an accessible electrical outlet.
1� Determine the location of the power unit on the wall; we recommend that the power unit be
fastened at 60” / 1,5m from the ground in order for the dust canister to be readily accessible;
allow 12” / 30cm clearance on all sides of the power unit. When possible, it is advisable to
install the power unit on a concrete wall in order to minimise the vibrations;
2� Gypsum wall:
• Prepare the wall by installing a plywood mounting board (not provided) 16” / 40cm high x
3/4” / 2cm thick and wide enough to be screwed to at least 2 studs;
• Fasten the mounting bracket to the mounting board with the provided screws;
3� Concrete wall:
• Drill the holes with a concrete drill bit;
• Insert the provided wall anchors into the drilled holes;
• install the mounting bracket with the provided screws into the anchors;
NOTE
»You can still install a plywood mounting (16” / 40cm x 10” /
25cm x 3/4” / 2cm) board if desired;
»You can use provided screws to fix mounting board on the wall,
but cannot use them for installing the mounting bracket on the
mounting board because of their length. You need to use shorter
screws (not provided).
IMPORTANT
Always use the right type of screws for the surface you are working with (wood,
concrete, metal…)
4� Insert the power unit bracket into the mounting bracket (Fig. 2).
5� Insert the PVC pipe into the air intake coupling; DO NOT GLUE!
6� Connect the controller module as explained in section 6;
7� Connect the power unit directly into an electrical outlet.
4. INSTALLATION
Table of contents
Other Husky Central Vacuum System manuals
Popular Central Vacuum System manuals by other brands

H-P Products
H-P Products CROSSVAC B600 operating instructions

Panasonic
Panasonic MCH1000 - BUILT-IN VACUUM SYS operating instructions

NADAIR
NADAIR 700-AL-22 user manual

NuTone
NuTone CV-352 installation guide

Hoover
Hoover Commercial WindTunnel owner's manual

SISTEM AIR
SISTEM AIR Wolly2 Guide for use and maintenance

Rehau
Rehau VACUCLEAN 2000 Fitting instructions

TECNOPLUS
TECNOPLUS Sistem-Air revo block professional Technical manual

TECNOPLUS
TECNOPLUS Sistem-Air Industrial Clean Basic Technical manual

NuTone
NuTone CV353 Specifications

Broan
Broan BQ2 Installation and user guide

Electrolux
Electrolux Afuera Planning & installation manual