Hussmann Insight ID6SUR User manual

MEDIUM TEMPERATURE
Installaon & Operaon Manual
P/N 0535974_R
April 2023
Spanish P/N 0535975
Shipped With Case Data Sheets
MANUAL - IO Insight Medium Temperature
Includes Front Door & Rear-Load Cases
Single & Mul-Deck
Keep in store for future reference!
IMPORTANT

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
ii
This warning does not mean that Hussmann products
will cause cancer or reproductive harm, or is in
violation of any product-safety standards or
requirements. As clarified by the California State
government, Proposition 65 can be considered more of
a‘right to know’ law than a pure product safetylaw.
When used as designed, Hussmann believes that our
products are notharmful. We provide the Proposition
65 warning to stay in compliance with California State
law. It is your responsibility to provide accurate
Proposition 65 warning labels to your customers when
necessary. For more information on Proposition 65,
please visit the California State government website.
August 31, 2018
BEFORE YOU BEGIN
Read these instructions completely and carefully.
This manual was written in accordance with originally prescribed equipment
that is subject to change. Hussmann reserves the right to change or revise
specifications and product design in connection with any feature of our products.
PERSONAL PROTECTION EQUIPMENT (PPE)
Only qualied personnel should install and service this equipment. Personal
Protection Equipment (PPE) is required whenever servicing this equipment.
Wear safety glasses, gloves, protective boots or shoes, long pants, and a long-
sleeve shirt when working with this equipment and handling glass. Observe all
precautions on tags, stickers, labels and literature attached to this equipment.
This warning does not mean that Hussmann products
will cause cancer or reproductive harm, or is in
violation of any product-safety standards or
requirements. As clarified by the California State
government, Proposition 65 can be considered more of
a‘right to know’ law than a pure product safetylaw.
When used as designed, Hussmann believes that our
products are notharmful. We provide the Proposition
65 warning to stay in compliance with California State
law. It is your responsibility to provide accurate
Proposition 65 warning labels to your customers when
necessary. For more information on Proposition 65,
please visit the California State government website.
August 31, 2018

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R iii
Medium Temperature Merchandisers
ANSI Z535.5 DEFINITIONS ........................iv
INSIGHT INSTALLATION TOOL LIST .............iv
INSTALLATION
UL Listing ......................................1-1
Federal / State Regulations .........................1-1
Location ........................................1-1
Product Temperatures .............................1-1
Shipping Damage ................................1-2
Unloading.......................................1-2
Exterior Loading .................................1-2
Unloading Using a Pallet Jack.......................1-3
Optional Casters and Dollies .......................1-3
Serial Plate Location ..............................1-3
QR Code .......................................1-3
Merchandisers Shipped with End Installed .............1-4
End Shipping Braces ..............................1-4
Shipping Rider ...................................1-4
Merchandiser Leveling .............................1-5
Joining Open Cases in Lineup .......................1-6
Sealing Lineup Joint .............................1-20
Rear Load and Door Cases Installation ..............1-21
Rear View Dimensions of Cases with External Sliding
Rear Loading Doors .............................1-22
Apply Gaskets ..................................1-24
Case Joining (Door & Rear Load Cases) .............1-26
Installing, Removing, Adjusting Doors ..............1-28
Adjusting EcoVision Doors ........................1-28
Adjusting Door Closing Speed .....................1-29
Replacing LED Vertical Mullion Light Bars ..........1-29
Installing End Assemblies .........................1-30
Partition Hardware ..............................1-35
Acrylic Partition Hardware ........................1-43
Installing Bumpers ...............................1-46
Installing Night Blinds ...........................1-47
Loading Blind Spring .............................1-49
Troubleshooting Night Blinds ......................1-50
REFRIGERATION / ELECTRICAL
Refrigerant ......................................2-1
Refrigerant Piping ................................2-1
Back Wall Piping Penetrations ......................2-2
Narrow and Wedge Case Connection use Shroud .......2-3
Multiplexing ....................................2-3
Line Sizing .....................................2-3
Oil Traps .......................................2-3
Pressure Drop ...................................2-3
Insulation .......................................2-3
Suction Line .....................................2-3
Liquid Line .....................................2-4
Refrigeration Thermostat ..........................2-4
Defrost Sequences ................................2-4
Merchandiser Electrical Data .......................2-4
Electrical Connections .............................2-4
Field Wiring .....................................2-4
Identication of Wiring ............................2-5
Sensor Location ..................................2-5
Electrical Access for Sign-Ready &
Flat-Front Fascias ...............................2-6
Handling Electrostatic Sensitive Devices
(Fan Selector) ...................................2-7
Installing Type II Fan Speed Selector Kit ..............2-8
Type II Fan Speed Selector Location .................2-9
DRIP PIPING / FIT & FINISH / SPLASHGUARDS
Waste Outlet and Water Seal ........................3-1
Installing Drip Piping..............................3-2
Flush Floor Drip Piping Example for Ultra Low
Front Cases .....................................3-3
Optional Waste Outlet Drip Piping Example for
Ultra Low Front Cases ............................3-4
Fascia Top Cap Alignment .........................3-7
Fascia Panel Alignment ............................3-8
Front Panel Alignment ...........................3-10
Installing End Splashguards .......................3-11
Installing Splashguard Brackets ....................3-13
Installing Splashguards ...........................3-14
Splashguard Alignment to Eliminate Gaps in
Cases Line-Up ..................................3-15
START UP / OPERATION
Start Up/Operation ...............................4-1
Load Limits .....................................4-1
Stocking ........................................4-1
Shelf Maximum Weight Limits ......................4-2
Multi-Deck Shelf Conguration .....................4-2
Installing Caseshield PTM(s) ........................4-3
LED Fixtures ....................................4-4
Procedure for Installing Lighted Shelves ..............4-5
Shelf LED Clip Installation .........................4-7
Product Stop Installation ...........................4-7
Installing FDA/NSF Required Thermometer ...........4-8
MAINTENANCE
Care and Cleaning ................................5-1
Fan Plenum .....................................5-1
Removable Return Air Grilles ......................5-1
Identication of Case Parts .........................5-2
Fascia Panels ....................................5-3
Exterior Surfaces .................................5-3
Interior Surfaces .................................5-3
Recommended Cleaning Instructions .................5-4
Weekly or Monthly ..............................5-4
Quarterly or Semiannually .........................5-4
Cleaning Honeycomb Assemblies ....................5-5
Cleaning Mirrors .................................5-6
Removing Interior Back Panels ......................5-6
Bottom Liner Repair ..............................5-7
Cleaning Coils ...................................5-8
Cleaning Stainless Steel Front Rails ..................5-8
Removing Scratches from Bumper ...................5-8
Cleaning Under Merchandisers .....................5-8
SERVICE
Replacing Fan Motors .............................6-1
Replacing Door Handles ...........................6-3
Repairing Aluminum Coil ..........................6-6
Warranty Information .............................6-7
TABLE OF CONTENTS

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
iv
MANUAL REVISION HISTORY
REVISION R
1. Removed Page 5-4; Revised fan motor service
instructions, Page 6-1, 6-2. Updated cleaning procedures,
Page 5-1. Updated warning colors
REVISION Q
Not used
REVISION P
1. Revised procedures for fan motor harness connector,
Section 5 & 6.
ANSI Z535.6-2011 (R2017)
Page 18
©2017 National Electrical Manufacturers Association
Annex A
Providing Information About Safety Messages in Collateral Materials and Product
Safety Signs and Labels
(Informative)
A1 Explanation of Signal Words and Symbols
Signal words and safety symbols that are used in a product’s collateral materials or on the product may
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
be used for this purpose.
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
A1.2 Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST
No reproduction or networking permitted without license from IHS
--`,,,``,,,``,``,``,`````,`,``,-`-`,,`,,`,`,,`---
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING indicates a hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION indicates a hazardous situation
which, if not avoided, could result in minor or
moderate injury.
NOTICE is used to address practices not
related to personal injury.
SAFETY INSTRUCTIONS (or equivalent)
signs indicate specic safety-related
instructions or procedures.
ANSI Z535.5 DEFINITIONS
The denitions below are used to clarify the magnitude and urgency of harm and damage, considering
problems arising from misuse. Relative to their potential danger, the definitions are divided
into four parts according to ANSI Z535 Series.
INSIGHT INSTALLATION
TOOL LIST
(recommended)
—¦—
Unloading From Trailer:
Lever Bar (also known as a Mule,
Johnson Bar, J-bar, Lever Dolly, and pry lever)
Moving Dolly
—¦—
Setting Case Line-Up:
Level, 4 ft (suggested)
Ratchet
¼in. Socket Drill Bit
5/16 in. Socket Drill Bit
½in. Socket - Deep Drill Bit
½in. Open End Wrench
Cordless Impact Drill
Caulking Gun
10 in. Adjustable Crescent Wrench
Pallet Jack

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R 1-1
Medium Temperature Merchandisers
UL LISTING
These merchandisers are manufactured to
meet ANSI/ UL 471 standard requirements for
safety. Proper installation is required to main-
tain the listing.
FEDERAL / STATE REGULATIONS
These merchandisers at the time they are man-
ufactured, meet all federal and state/ provincial
regulations. Proper installation is required to
ensure these standards are maintained. Near
the serial plate, each merchandiser carries a
label identifying the environment for which the
merchandiser was designed for use. A Type II
fan speed control kit is required for each mer-
chandiser to operate at Type II conditions.
ANSI/NSF-7 Type I – Display Refrigerator / Freezer
Intended for 75°F (24°C) / 55% RH Ambient Application
ANSI/NSF-7 Type II – Display Refrigerator / Freezer
Intended for 80°F / 55% RH Ambient Application
ANSI/NSF-7 – Display Refrigerator
Intended for Bulk Produce
LOCATION
These merchandisers are designed for displaying
products in air conditioned stores where
temperature is maintained at or below the
ANSI/ NSF-7 specied level and relative
humidity is maintained at or below 55%.
Placing refrigerated merchandisers in direct
sunlight, near hot tables or near other heat
sources could impair their efciency. Like
other merchandisers, these are sensitive to air
disturbances. Air currents passing around
merchandisers will seriously impair their
operation. Do NOT allow air conditioning,
electric fans, open doors or windows, etc. to
create air currents around the merchandisers.
PRODUCT TEMPERATURE
Product should always be maintained at proper
temperature. This means that from the time the
product is received, through storage, preparation
and display, the temperature of the product
must be controlled to maximize product life.
INSTALLATION
Merchandiser must operate for 24 hours
before loading product!
Regularly check merchandiser temperatures.
Do not break the cold chain. Keep products in
cooler or freezer before loading into merchandiser.
Medium temperature merchandisers are designed
for loading ONLY pre-chilled products.
Low temperature merchandisers are designed
for loading ONLY frozen products.
A 1.5inch (38 mm) space between the rear
of the merchandiser and wall must be main-
tained for air circulation. However, in high
ambient conditions, sweating may still occur.
If this happens install a method of forced
ventilation such as a fan ventilation kit.
»Use caution when working around refrigeration
lines or water lines. Damage to equipment and/
or personal injury could occur.
ANSI Z535.6-2011 (R2017)
Page 18
©2017 National Electrical Manufacturers Association
Annex A
Providing Information About Safety Messages in Collateral Materials and Product
Safety Signs and Labels
(Informative)
A1 Explanation of Signal Words and Symbols
Signal words and safety symbols that are used in a product’s collateral materials or on the product may
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
be used for this purpose.
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
A1.2 Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST
No reproduction or networking permitted without license from IHS
--`,,,``,,,``,``,``,`````,`,``,-`-`,,`,,`,`,,`---

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
1-2
SHIPPING DAMAGE
All equipment should be thoroughly examined
for shipping damage before and during unloading.
This equipment has been carefully inspected at
our factory. Any claim for loss or damage must
be made to the carrier. The carrier will provide
any necessary inspection reports and/or claim
forms.
Apparent Loss or Damage
If there is an obvious loss or damage, it must be
noted on the freight bill or express receipt and
signed by the carrier’s agent; otherwise, carrier
may refuse claim.
Concealed Loss or Damage
When loss or damage is not apparent until after
equipment is uncrated, retain all packing materials
and submit a written request to the carrier for
inspection, within 15 days.
UNLOADING
Improper handling may cause damage to the
merchandiser when unloading. Use the shipping
brace and arched pod locations to lift when
unloading cases.
1. Do not drag the merchandiser out of the
trailer. Use a Johnson bar (mule).
2. Do not lift the case by the liner. Lift with
the metal case base, arched plastic pods or the
shipping brace.
3. Do not lift from the bottom edge of the end
panel.
EXTERIOR LOADING
Do NOT walk on top or inside of merchandisers
or damage to the merchandisers and serious
personal injury could occur. They are noT
sTrucTurally designed To supporT excessive
exTernal loading such as the weight of a person.
Use caution when working around refrigera-
tion lines or water lines, damage to equipment
and personal injury could occur.
»If the case is to be moved using a fork lift,
position the forks of the lift directly under the
arched pods or shipping rails. Use extreme
caution when transporting cases. Personal injury
or death could result if a case falls on personnel.
ANSI Z535.6-2011 (R2017)
Page 18
©2017 National Electrical Manufacturers Association
Annex A
Providing Information About Safety Messages in Collateral Materials and Product
Safety Signs and Labels
(Informative)
A1 Explanation of Signal Words and Symbols
Signal words and safety symbols that are used in a product’s collateral materials or on the product may
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
be used for this purpose.
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
A1.2 Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST
No reproduction or networking permitted without license from IHS
--`,,,``,,,``,``,``,`````,`,``,-`-`,,`,,`,`,,`---
»Do not walk on case. Do not store items or
ammable materials atop the case.
ANSI Z535.6-2011 (R2017)
Page 18
©2017 National Electrical Manufacturers Association
Annex A
Providing Information About Safety Messages in Collateral Materials and Product
Safety Signs and Labels
(Informative)
A1 Explanation of Signal Words and Symbols
Signal words and safety symbols that are used in a product’s collateral materials or on the product may
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
be used for this purpose.
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
A1.2 Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST
No reproduction or networking permitted without license from IHS
--`,,,``,,,``,``,``,`````,`,``,-`-`,,`,,`,`,,`---
Arched Pod
Location
Shipping
Brace
J-Bar
LIFT
POINTS
Shipping Brace &
Arched Pod
Installer lift at either
of THESE POINTS
with J-Bar when
moving case.
LIFT HERE
LIFT
HERE

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R 1-3
Medium Temperature Merchandisers
UNLOADING USING A PALLET JACK
A pallet jack is also very helpful in moving a
merchandiser to its permanent location. It can
also be used to remove optional casters or to
shim the case.
OPTIONAL CASTERS AND DOLLIES
Cases may be equipped with factory installed
casters or dollies. Instructions for removing
the casters or dollies are included in a separate
document, shipped with the case. Use caution
when transporting cases from the truck to the
store location.
SERIAL PLATE LOCATION
Serial plates are located on the left side, facing
the case. The serial plate contains information
about the specic model and its operating
parameters.
NOTE: A second serial plate for multi-deck cases is
also located behind the return air grille in the same
location as singe-deck cases (shown below).
QR CODE
Insight cases have a QR code located on the serial
plate(s). Once you scan the QR code with a
smart phone, all of the information about that
case will be at your ngertips. Links to installation
videos, data sheets with case specications, the
installation and operation manual, as well as a
link to replacement parts from Hussmann’s
Performance Parts Website.
»Use caution when moving cases with casters
or dollies. Damage to equipment and personal
injury could occur from improper handling.
ANSI Z535.6-2011 (R2017)
Page 18
©2017 National Electrical Manufacturers Association
Annex A
Providing Information About Safety Messages in Collateral Materials and Product
Safety Signs and Labels
(Informative)
A1 Explanation of Signal Words and Symbols
Signal words and safety symbols that are used in a product’s collateral materials or on the product may
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
be used for this purpose.
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
A1.2 Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST
No reproduction or networking permitted without license from IHS
--`,,,``,,,``,``,``,`````,`,``,-`-`,,`,,`,`,,`---
Serial Plate inside Canopy (multi-deck)
Case Caster
Serial Plate behind
return air grille
(single-deck)
QR Code
Location

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
1-4
MERCHANDISERS SHIPPED
WITH END INSTALLED
If the merchandiser was shipped with the end
installed, two long bolts were used to hold the
shipping brace to the end. If the shipping bolts
are reinserted after removing the brace, they
will extend into the product area. Therefore, be
sure To replace These bolTs wiTh The shorTer
bolTs provided.NSF requires any bolt or screw
in the product area be capped or cut off if it
has more than three exposed threads.
Be careful not to damage the factory
installed end while moving the
merchandiser.
END SHIPPING BRACES
Move the merchandiser as close as possible to
its permanent location, then remove all packaging.
Check for damage before discarding packaging.
Remove all separately packed accessories such
as kits and shelves.
Do not remove end braces until joining begins.
Recycle wooden braces and hardware.
SHIPPING RIDER
Some merchandisers are shipped on a rider to
protect the factory installed front legs, and to
make positioning the merchandiser easier. To
remove the rider, remove bolts attaching rider to
each leg.
Shipping Braces
Shipping Rider







K
 
 






   





Lorem ipsum
Remove 6 Screws and
Wooden Supports Prior to
Moving Case into Position
(rear rail will remain
attached to merchandiser)
Ultra Low
Front Cases
»Do not remove shipping braces
until the merchandisers are
positioned for installation.
ANSI Z535.6-2011 (R2017)
Page 18
©2017 National Electrical Manufacturers Association
Annex A
Providing Information About Safety Messages in Collateral Materials and Product
Safety Signs and Labels
(Informative)
A1 Explanation of Signal Words and Symbols
Signal words and safety symbols that are used in a product’s collateral materials or on the product may
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
be used for this purpose.
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
A1.2 Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST
No reproduction or networking permitted without license from IHS
--`,,,``,,,``,``,``,`````,`,``,-`-`,,`,,`,`,,`---

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R 1-5
Medium Temperature Merchandisers
»Tipping Hazard! Case tipping may occur if cases are
not properly leveled and secured, or if cases are not
properly loaded.
ANSI Z535.6-2011 (R2017)
Page 18
©2017 National Electrical Manufacturers Association
Annex A
Providing Information About Safety Messages in Collateral Materials and Product
Safety Signs and Labels
(Informative)
A1 Explanation of Signal Words and Symbols
Signal words and safety symbols that are used in a product’s collateral materials or on the product may
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
be used for this purpose.
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
A1.2 Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
may be explained in collateral materials. The following artwork may be used for this purpose.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST
No reproduction or networking permitted without license from IHS
--`,,,``,,,``,``,``,`````,`,``,-`-`,,`,,`,`,,`---
MERCHANDISER LEVELING
Merchandisers must be installed level to ensure
proper operation of the refrigeration system
and to ensure proper drainage of defrost water.
Pay close attention to case position during all
steps of setting, joining and leveling.
NOTE: Begin lineup leveling from the highest
point of the store floor.
Preparation
1. Using store blueprints, measure off and
mark on oor the exact dimensions/locations
of the merchandiser footprint. A 1½ inch space
is required behind each merchandiser to prevent
condensation.
2. Snap a chalk line for the front and rear
positions of the base pods.
3. Mark the location of each joint from front
to back lines.
4. use supplied shims To level case.Shims are
to be inserted under the black, plastic base pods.
Case Lineup Leveling
1. FLOORS ARE NOT LEVEL! The
whole lineup must be leveled on the same
plane, left to right and front to back. This
means that the entire lineup must be brought
up to the level of the highest case in the lineup.
Along the lines previously marked, nd the
highest point of the oor by:
• Walking the oor and noticing any dips or
mounds;
• Using a string level; and
• Using a transit.
2. Position the rst merchandiser at the highest
point on the oor. Work outward from that
point to create the merchandiser lineup.
3. Use a 48 inch (1220mm) or longer level for
end-to-end leveling. The rear edge of the top
foam panel of the merchandiser is a good location
for the level at the rear of the case.
4. For leveling the merchandiser front-to-rear,
a 24 inch (610 mm) level should be placed on
the lower ange of the merchandiser end frame.
If the merchandiser has a factory installed end,
the level should be placed on the canopy support
brackets on top of the merchandiser. Suggested
level locations are shown in the illustration.
Shim
Shim
Shim Case
Pallet Jack
Shim
Shim
Pallet Jack

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
1-6 Note:
See PAGE 1-21 at end of manual for joining
rear load and door cases.
Bolt-5/16 x 4 1/2
Bolt-5/16 x 7
Washer Flat-5/16
Nut Hex-3/8 Serr Flange
Nut Hex-5/16
Bolt-5/16 x 2 3/4
Bolt-5/16 x 3/4
Pin-Alignment
Cone-Alignment
Washer Lock-5/16
Cover-Handrail Joint
Washer Lock-1/4
Nut Hex-1/4
Screw-Cap 1/4 x 3/4
Plate-Bottom Door Rail Alignment
Bracket-Case Joining
Bracket-Fascia Alignment IC2 & IC3
Screw-Sheet Metal #8 x 5/8
IMPORTANT:
Do not pull cases together with bolts. Cases must be moved
together as close as possible. Follow sequence balloons to
tighten bolts.
Apply gasket to only one side of case joint.
Remove end shipping braces as described on Page 1-4.
Cases must be leveled as described on Page 1-5.
Removed any casters - if installed.
Install case lineup from left to right.
Remove shelves, display racks, pans & interior back panels at
the joining area.
Insert gasket into case channels the entire length with no gaps.
Do not stretch gasket, especially around corners.
Do not butt gaskets, always overlap them.
Remove paper backing after gasket has been applied.
Perimeter gasket is required by NSF.
Apply a continuous bead of neutral curing silicone sealant.
Joints must be air tight to prevent formation of ice of condensation.
JOINING OPEN CASES IN A LINEUP
Multi Deck
Qty/Each
Convertible
Qty/Each
Single Deck
Qty/Each
Door Multi
Deck Qty/Each
SEALER SILICONE ADHESIVE 1 1 1 1
GASKET 1/2 X 1/2 X 180 2 1 1 2
SCREW-SHEET METAL #8 X 5/8 PHIL HX HD N/A 1 N/A N/A
SCREW-CAP 1/4 x 3/4 HEX N/A N/A N/A 2
BOLT HEX CAP 5/16 x 3/4 1 1 1 1
BOLT 5/16 x 2 3/4 GRADE 5 ZINC PLATED TAP 2 N/A N/A 2
BOLT- TAP, 5/16 x 4 1/2, STEEL, ZINC FINISH, GR5 (Qty Varies) 5 2 1 5
BOLT- TAP, 5/16 x 7, STEEL, ZINC FINISH, GR5 1 1 1 1
WASHER-FLAT 5/16” ZINC (Qty Varies) 13 5 3 13
LOCKWSHR 1/4 SPLT STL N/A N/A N/A 2
LOCKWSHR 5/16 SPLT STL 1 1 1 1
NUT-HEX 1/4 N/A N/A N/A 2
NUT-HEX 5/16 STEEL ZINC FINISH GRADE 8 (Qty Varies) 9 4 3 9
NUT-HEX 3/8-24 SERRATED FLANGE 4 N/A N/A 4
PIN-ALIGNMENT 1 1 1 N/A
CONE-CASE ALIGNMENT (Qty Varies) 4 2 2 4
PLATE-BOTT DOOR RAIL ALIGNMENT N/A N/A N/A 1
BRACKET-CASE JOINING 4 N/A N/A 4
BRACKET-FASCIA ALIGNMENT IC2 & IC3 N/A 1 N/A N/A
COVER-HAND RAIL JOINT 1 1 1 N/A
TAPE-BUTYL 1/16 x 2” X 49” 1 1 1 1
Screw-Sheet Metal #8 x 5/8
Screw-Cap 1/4 x 3/4
Bolt-5/16 x 3/4
Bolt-5/16 x 2 3/4
Bolt-5/16 x 4 1/2
Bolt-5/16 x 7
Washer Flat-5/16
Washer Lock-1/4
Washer Lock-5/16
Nut Hex-1/4
Nut Hex-5/16
Nut Hex-3/8 Serr Flange
Pin-Alignment
Cone-Alignment
Plate-Bottom Door Rail Alignment
Bracket-Case Joining
Bracket-Fascia Alignment IC2 & IC3
Cover-Handrail Joint
JOINING AND SEALING HARDWARE

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R 1-7
Medium Temperature Merchandisers
Smooth
Surface
Minimum 1 1/2 in space
between case &wall
Smooth
Surface
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
65/16 X 4 1/2 BOLT
75/16 X 4 1/2 BOLT
45/16 X 4 1/2 BOLT
B
A
A
A
&ALIGNMENT CONE
& ALIGNMENT CONE
&ALIGNMENT CONE
&ALIGNMENT CONE
C
55/16 X 3/4 BOLT
85/16 X 2 3/4 BOLT
95/16 X 2 3/4 BOLT
A
D
B
LEGEND:
A = 1/2 x 1/2 INCH GASKET
B = NEUTRAL CURING SILICONE SEALANT
C = PIN-ALIGNMENT
D = COVER-HAND RAIL JOINT
APPLY GASKETS
(MULTI-DECK)
IP4 / IM5 / ID5 / ID6 / IC6 / IC4
Case bolting details begin on the
next page.
IMPORTANT:
Do not pull cases together with bolts. Cases must be moved
together as close as possible Follow sequence balloons to
tighten bolts.
Merchandiser case joint & end gasket to be applied on only one
side of joint.
Merchandiser partition gasket to be applied on both sides of
joint.
Remove end shipping braces as described on Page 1-4
Cases must be leveled as described on Page 1-5
Removed any casters - if installed
Install case lineup from left to right
Remove shelves, display racks, pans & interior back panels at
the joining area
Insert gasket into case channels the entire length with no gaps
Do not stretch gasket, especially around corners
Do not butt gaskets, always overlap them
Remove paper backing after gasket has been applied
Perimeter gasket is required by NSF
Apply a continuous bead of neutral curing silicone sealant
Joints must be air tight to prevent formation of ice or condensation.

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
1-8
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
&ALIGNMENT CONE
& ALIGNMENT CONE
&ALIGNMENT CONE
C
65/16 X 4 1/2 BOLT
75/16 X 4 1/2 BOLT
45/16 X 4 1/2 BOLT
&ALIGNMENT CONE
85/16 X 2 3/4 BOLT
95/16 X 2 3/4 BOLT
55/16 X 3/4 BOLT
D
PUSH COVER
IN THIS
DIRE CTION
TO SNAP FIT
C
O
VE
R
-
H
A
N
D
R
AI
L J
OI
N
T
SLIDE BRACKET
TO COMPLETE
JOINT
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
&ALIGNMENT CONE
& ALIGNMENT CONE
&ALIGNMENT CONE
C
65/16 X 4 1/2 BOLT
75/16 X 4 1/2 BOLT
45/16 X 4 1/2 BOLT
&ALIGNMENT CONE
85/16 X 2 3/4 BOLT
95/16 X 2 3/4 BOLT
55/16 X 3/4 BOLT
D
PUSH COVER
IN THIS
DIRE CTION
TO SNAP FIT
C
O
VE
R
-
H
A
N
D
R
AI
L J
OI
N
T
SLIDE BRACKET
TO COMPLETE
JOINT
LEGEND:
C = PIN-ALIGNMENT
CASE JOINING (MULTI-DECK / REAR LOAD)
IP4 / IM5 / ID5 / ID6 / IC6 / IC4
Refer to detail views
Do not pull cases together with bolts. Cases
must be moved together as close as possible.
Follow sequence balloons to tighten bolts.

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R 1-9
Medium Temperature Merchandisers
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
&ALIGNMENT CONE
& ALIGNMENT CONE
&ALIGNMENT CONE
C
65/16 X 4 1/2 BOLT
75/16 X 4 1/2 BOLT
45/16 X 4 1/2 BOLT
&ALIGNMENT CONE
85/16 X 2 3/4 BOLT
95/16 X 2 3/4 BOLT
55/16 X 3/4 BOLT
D
PUSH COVER
IN THIS
DIRE CTION
TO SNAP FIT
C
O
VE
R
-
H
A
N
D
R
AI
L J
OI
N
T
SLIDE BRACKET
TO COMPLETE
JOINT
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
&ALIGNMENT CONE
& ALIGNMENT CONE
&ALIGNMENT CONE
C
65/16 X 4 1/2 BOLT
75/16 X 4 1/2 BOLT
45/16 X 4 1/2 BOLT
&ALIGNMENT CONE
85/16 X 2 3/4 BOLT
95/16 X 2 3/4 BOLT
55/16 X 3/4 BOLT
D
PUSH COVER
IN THIS
DIRE CTION
TO SNAP FIT
C
O
VE
R
-
H
A
N
D
R
AI
L J
OI
N
T
SLIDE BRACKET
TO COMPLETE
JOINT
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
&ALIGNMENT CONE
& ALIGNMENT CONE
&ALIGNMENT CONE
C
65/16 X 4 1/2 BOLT
75/16 X 4 1/2 BOLT
45/16 X 4 1/2 BOLT
&ALIGNMENT CONE
85/16 X 2 3/4 BOLT
95/16 X 2 3/4 BOLT
55/16 X 3/4 BOLT
D
PUSH COVER
IN THIS
DIRE CTION
TO SNAP FIT
C
O
VE
R
-
H
A
N
D
R
AI
L J
OI
N
T
SLIDE BRACKET
TO COMPLETE
JOINT
This Bolt location is
optional for some
installed kits.
CASE JOINING (MULTI-DECK / REAR LOAD)
IP4 / IM5 / ID5 / ID6 / IC6 / IC4
Refer to detail views

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
1-10
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
&ALIGNMENT CONE
& ALIGNMENT CONE
&ALIGNMENT CONE
C
65/16 X 4 1/2 BOLT
75/16 X 4 1/2 BOLT
45/16 X 4 1/2 BOLT
&ALIGNMENT CONE
85/16 X 2 3/4 BOLT
95/16 X 2 3/4 BOLT
55/16 X 3/4 BOLT
D
PUSH COVER
IN THIS
DIRE CTION
TO SNAP FIT
C
O
VE
R
-
H
A
N
D
R
AI
L J
OI
N
T
SLIDE BRACKET
TO COMPLETE
JOINT
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
& ALIGNME NT CONE
C
65/16 X 4 1/2 BOLT
75/16 X 4 1/2 BOLT
45/16 X 4 1/2 BOLT
& ALIGNMENT CONE
85/16 X 2 3/4 BOLT
95/16 X 2 3/4 BOLT
55/16 X 3/4 BOLT
D
PUSH COVER
IN THIS
DIRE CTION
TO SNAP FIT
C
O
VE
R
-
H
A
N
D
R
AI
L J
OI
N
T
SLIDE BRACKET
TO COMPLETE
JOINT
LEGEND:
D = COVER-HAND RAIL JOINT
Cover-Hand Rail Joint
CASE JOINING (MULTI-DECK / REAR LOAD)
IP4 / IM5 / ID5 / ID6 / IC6 / IC4
Refer to detail views
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
FACETED FASCIA
RIG HT SIDE VIE W
ELLIPSE FASCIA
RIGHT SIDE VIEW
F LAT F ASCIA
RIG HT SIDE VIE W
E
PUSH C OVE R
IN THIS
DIRE CTIO N
TO SNAP F IT
Push Cover
in this direction
to snap fit

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R 1-11
Medium Temperature Merchandisers
&ALIGNMENT CONE
&ALIGNMENT CONE
Minimum 1 1/2 in. Space
between case & wall
LEGEND:
A=1/2 X 1/2 INCH GASKET
B=NEUTRAL CURING SILICONE SEALANT
C=PIN-ALIGNMENT
D=COVER-HAND RAIL JOINT
E=BRACKET-FASCIA ALIGNMENT
IMPORTANT:
Do not pull cases together with bolts. Cases must be moved
together as close as possible Follow sequence balloons to
tighten bolts.
Merchandiser case joint & end gasket to be applied on only one
side of joint.
Merchandiser partition gasket to be applied on both sides of
joint.
Remove end shipping braces as described on Page 1-4
Cases must be leveled as described on Page 1-5
Removed any casters - if installed
Install case lineup from left to right
Remove shelves, display racks, pans & interior back panels at
the joining area
Insert gasket into case channels the entire length with no gaps
Do not stretch gasket, especially around corners
Do not butt gaskets, always overlap them
Remove paper backing after gasket has been applied
Perimeter gasket is required by NSF
Apply a continuous bead of neutral curing silicone sealant
Joints must be air tight to prevent formation of ice or condensation.
APPLY GASKETS
(CONVERTIBLE)
IC2 / IC2X / IC3
Case bolting details begin on the
next page.

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
1-12
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
PUSH COVER
IN THIS
DIRECTION
TO SNAP FIT
E
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
PUSH C OVER
IN THIS
DIRECTION
TO SNAP F IT
E
LEGEND:
C=PIN-ALIGNMENT
E=BRACKET-FASCIA ALIGNMENT
CASE JOINING (CONVERTIBLE)
IC2 / IC2X / IC3
Refer to detail views
Do not pull cases together with bolts. Cases
must be moved together as close as possible.
Follow sequence balloons to tighten bolts.

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R 1-13
Medium Temperature Merchandisers
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
PUSH C OVER
IN THIS
DIRECTION
TO SNAP FIT
E
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
FACETED FASCIA
RIGHT SIDE VIE W
ELLIPSE FASCIA
RIGHT SIDE VIEW
F LAT F ASCIA
RIGHT SIDE VIE W
E
PUSH C OVE R
IN THIS
DIRE CT IO N
TO SNAP F IT
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
FACETED FASCIA
RIGHT SIDE VIE W
ELLIPSE FASCIA
RIGHT SIDE VIEW
F LAT F ASCIA
RIGHT SIDE VIE W
E
PUSH C OVE R
IN THIS
DIRE CT IO N
TO SNAP F IT
LEGEND:
E=BRACKET-FASCIA ALIGNMENT
(Can be modied by hand for better t if necessary)
Ellipse Fascia
right side view
Flat Fascia
right side view
Existing Fascia Brackets
will locate Alignment
Bracket left to right
Faceted Fascia
right side view
CASE JOINING (CONVERTIBLE)
IC2 / IC2X / IC3
Refer to detail views
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
FACETED FASCIA
RIGHT SIDE VIE W
ELLIPSE FASCIA
RIGHT SIDE VIEW
F LAT F ASCIA
RIGHT SIDE VIE W
E
PUSH C OVE R
IN THIS
DIRE CT IO N
TO SNAP F IT
Screw will locate
alignment bracket left
to right
Screw will locate
alignment bracket left
to right
Bracket
Bracket
Bracket

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
1-14
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLET E
JOINT
PUSH COVER
IN THIS
DIRECTION
TO SNAP FIT
E
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
PUSH COVER
IN THIS
DIRECTION
TO SNAP FIT
E
Slide Bracket to
complete Joint
CASE JOINING (CONVERTIBLE)
IC2 / IC2X / IC3
Refer to detail views

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
P/N 0535974_R 1-15
Medium Temperature Merchandisers
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLET E
JOINT
PUSH COVER
IN THIS
DIRECTION
TO SNAP FIT
E
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JO
INT
D
SLIDE BRACKET
TO COMPLETE
JOINT
PUSH COVER
IN THIS
DIRECTION
TO SNAP FIT
E
LEGEND:
D = COVER-HAND RAIL JOINT
CASE JOINING (CONVERTIBLE)
IC2 / IC2X / IC3
Refer to detail views
Cover-Hand
Rail Joint
25/16 X 4 1/2 BOLT
15/16 X 4 1/2 BOLT
35/16 X 7 BOLT
& ALIGNMENT CONE
& ALIGNMENT CONE
E
C
55/16 X 3/4 BOLT
COVER-HAND RAIL JOINT
D
SLIDE BRACKET
TO COMPLETE
JOINT
FACETED FASCIA
RIG HT SIDE VIE W
ELLIPSE FASCIA
RIGHT SIDE VIEW
F LAT F ASCIA
RIG HT SIDE VIE W
E
PUSH C OVE R
IN THIS
DIRE CTIO N
TO SNAP F IT
Push Cover
in this direction
to snap fit

P/N 0535974 _R U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
1-16
& ALIGNM ENT CONE
& ALIGNM ENT CONE
LEGEND:
A = 1/2 x 1/2 INCH GASKET
B = NEUTRAL CURING SILICONE SEALANT
C = PIN-ALIGNMENT
D = COVER-HAND RAIL JOINT
IMPORTANT:
Do not pull cases together with bolts. Cases must be moved
together as close as possible Follow sequence balloons to
tighten bolts.
Merchandiser case joint & end gasket to be applied on only one
side of joint.
Merchandiser partition gasket to be applied on both sides of
joint.
Remove end shipping braces as described on Page 1-4
Cases must be leveled as described on Page 1-5
Removed any casters - if installed
Install case lineup from left to right
Remove shelves, display racks, pans & interior back panels at
the joining area
Insert gasket into case channels the entire length with no gaps
Do not stretch gasket, especially around corners
Do not butt gaskets, always overlap them
Remove paper backing after gasket has been applied
Perimeter gasket is required by NSF
Apply a continuous bead of neutral curing silicone sealant
Joints must be air tight to prevent formation of ice or condensation.
APPLY GASKETS
(SINGLE-DECK)
IIM1 / IP1
Case bolting details begin on the
next page.