Hussmann ECOSHINE ULTRA LED User manual

EcoShine ULTRA
Canopy Light
ECOSHINE ULTRA LEDs
Installation & Specications Guide
P/N 0524791_J
October 2021
Spanish P/N 0527937
MANUAL- KIT ECOSHINE ULTRA LED, MULTI-DECK
Upgrade Installation Guide
IMPORTANT
Keep in Store for Future Reference
Multi-deck Canopy, Shelf, & Rail LEDs
EcoShine ULTRA
Shelf Light


Indicate[s] a hazardous situaon
which, if not avoided, will result in death or
serious injury.
 –Indicate[s] a hazardous situ-
aon which, if not avoided, could result in
death or serious injury.
 – Indicate[s] a hazardous situaon
which, if not avoided, could result in minor
or moderate injury.
 Not related to personal injury –
Indicates[s] situaons, which if not avoided, could
result in damage to equipment.
BEFORE YOU BEGIN
Read the safety information completely and carefully.
Please wear all required personal protecve equipment
according to OSHA regulaons, and be sure to comply with
the precauons described in this manual to protect you and
others from possible harm. The ANSI denions below detail
and clarify the magnitude and urgency of potential harm, dam-
age and problems arising from misuse or improper installaon.
Relave to their potenal danger, the denions are divided
into four parts as dened by ANSI Z535 Series.
Working Near the Public
Cordon o all work areas with cones, cauon tape, warning
signs and/or barricades. Maintain a work area of at least 5
feet from the public. Is a second person required to prevent
the public from entering the work area when the work area
cannot be adequately cordoned o?
Electrical Hazards
Are all live electrical hazards protected from public access;
i.e., de-energized/locked out or cordoned o? Is proper
signage in place? Make sure the work area is cordoned
o.
Electrical / LOTO
Does the project require you to work with live electricity?
If yes, have you received appropriate training? Do you
have appropriate locks and tags to de-energize or isolate
the electrical supply?
• Read and observe all CAUTIONS and WARNINGS shown
throughout these instrucons.
• Each person working on or near the installaon
described must wear safety glasses or goggles.
• Block access to the work area by customers or other
personnel to prevent injury.
• Read and follow all industry safety recommendaons
and established procedures.
• Wiring must be 2 wire with ground and rated for
75°C (176°F).
SAFETY
REVISION HISTORY
REVISION J— Added new horizontal ULTRA
LEDs

Hussmann Corporation • Bridgeton, Missouri 63044-2483 U.S.A.
LED Lighting Canopy, Shelf and Rail P/N 0524791_J
3
This warning does not mean that Hussmann products
will cause cancer or reproductive harm, or is in
violation of any product-safety standards or
requirements. As clarified by the California State
government, Proposition 65 can be considered more of
a‘right to know’ law than a pure product safetylaw.
When used as designed, Hussmann believes that our
products are notharmful. We provide the Proposition
65 warning to stay in compliance with California State
law. It is your responsibility to provide accurate
Proposition 65 warning labels to your customers when
necessary. For more information on Proposition 65,
please visit the California State government website.
August 31, 2018
This warning does not mean that Hussmann products will cause
cancer or reproductive harm, or is in violation of any product-safety
standards or requirements. As clarified by the California State
government, Proposition 65 can be considered more of a ‘right
to know’ law than a pure product safety law. When used as de-
signed, Aperion believes that our products are not harmful. We
provide the Proposition 65 warning to stay in compliance with
California State law. It is your responsibility to provide accurate
Proposition 65 warning labels to your customers when necessary.
For more information on Proposition 65, please visit the California
State government website.
— LOCK OUT / TAG OUT —
To avoid serious injury or death from electrical
shock, always disconnect the electrical power at
the main disconnect when servicing or replacing
any electrical component. This includes, but is
not limited to, such items as lights, fans and
heaters.
Risk of re or electric shock. Luminaire wiring
and electrical parts installation requires
knowledge of electrical systems. Only qualied
service technicians shoould install or service
this equipment. If not qualied, do not attempt
installation. Contact a qualied electrician.
Only those open holes indicated in the pho-
tographs and / or drawings may be made or
altered as a result of kit installation. Do not
leave any other open holes in an enclosure of
wiring or electrical components.
— LOCK OUT / TAG OUT —
To avoid serious injury or death from electrical
shock, always disconnect the electrical power
at the main disconnect when servicing or
replacing any electrical component. This
includes, but is not limited to, such items as
doors, lights, fans, heaters, and thermostats.

U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • WWW.HUSSMANN.COM
P/N 0524791_J
4
SAFETY ............................ 2
Working near the Public ............... 2
Electrical Hazards .................... 2
Electrical / LOTO .................... 2
WARNINGS ........................ 2
ANSI Z535.5 Denitions ............... 2
Additional Warnings .................. 3
GENERAL INFORMATION .......... 5
LED Light Fixtures ................... 5
Electrical Connections . . . . . . . . . . . . . . . . . 5
Identication of Wiring ................ 5
Shipping Damage .................... 5
Always*Clear™Glass .................. 6
LED Light Fixtures ................... 6
Cleaning LED Fixtures ................ 6
OVERVIEW ........................ 7
For Your Safety ...................... 7
Electrical Connections ................. 7
Identication of Wiring ................ 7
Shipping Damage ..................... 8
Remove Existing Fluorescent Lighting .... 8
LED Lighting for Multi-Deck Canopy
Parts List............................ 9
Horizontal LED Shelf
Lighting for Multi-Deck Merchandisers
Parts List ........................ 10
Parts Identication Chart ............. 11
Recommended Tools and Supplies ...... 11
Fluorescent Equipment Removal ....... 12
Connect Wiring to Power Supply ....... 13
Shelf Light Installation ............... 14
Canopy Light Installation ............. 17
TABLE OF CONTENTS
IMPORTANT
KEEP IN STORE FOR FUTURE REFERENCE
Quality that sets industry standards!
12999 St. Charles Rock Road • Bridgeton, MO 63044-2483
U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900
www.hussmann.com
© 2021 Hussmann Corporation

Hussmann Corporation • Bridgeton, Missouri 63044-2483 U.S.A.
LED Lighting Canopy, Shelf and Rail P/N 0524791_J
5
LED LIGHT FIXTURES
EcoShine ULTRA LEDs were specically designed
to maximize product appeal and reduce energy
costs. These LEDs work well for dimming or on/
off operation using an occupancy sensor (option-
al kits). They can be turned on and off in a cold
environment with no warm-up time and no nega-
tive impact on lamp life. This instruction explains
how to remove original equipment manufactured
(OEM) uorescent lamp xtures and replace them
with Hussmann LED light bars.
ELECTRICAL CONNECTIONS
All wiring must be in compliance with NEC and
local codes. All electrical connections are to be
made in the wireway or mullion or LED light
xture.
IDENTIFICATION OF WIRING
Leads for all electrical circuits are identied by
colored plastic bands. These bands correspond
to the color code sticker (shown below) located
inside the merchandiser’s wireway cover. Anthony
doors may not conform to this chart. Refer to the
manufacturer’s manual for their information.
SHIPPING DAMAGE
All equipment should be thoroughly examined for
shipping damage before and during unloading.
This equipment has been carefully inspected at
our factory. Any claim for loss or damage must be
made to the carrier. The carrier will provide any
necessary inspection reports and/or claim forms.
Apparent Loss Or Damage
If there is an obvious loss or damage, it must be
noted on the freight bill or express receipt and
signed by the carrier’s agent; otherwise, carrier may
refuse claim.
Concealed Loss Or Damage
When loss or damage is not apparent until after
equipment is uncrated, retain all packing materials
and submit a written request to the carrier for
inspection, within 15 days.
Missing Parts
Every effort is made to ship all parts for the kit.
The Hussmann Service Center can be reached by
calling
• from U.S. & Canada 1-800-922-1919
• from Mexico 1-800-890-2900
GENERAL INFORMATION
WIRING COLOR CODE
Leads for all electrical circuits are identified by a colored plastic band:
neutral wire for each circuit has either White insulation or a White plastic
sleeve in addition to the color band.
Pink ........... RefRig. TheRmosTaT Low TemP. oRange oR
LighT BLue . RefRig. TheRmosTaT noRm TemP. Tan ...........LighTs
DaRk BLue . DefRosT TeRm. TheRmosTaT maRoon ....RecePTacLes
PuRPLe ....... conDensaTe heaTeRs YeLLow .....DefRosT heaTeRs 120V
BRown ....... fan moToRs ReD ..........DefRosT heaTeRs 208V
gReen*....... gRounD *eiTheR coLoReD sLeeVe oRcoLoReD insuLaTion
ELECTRICIAN NOTE: Use copper conductor wire only.
CASE MUST BE GROUNDED
These aRe maRkeR coLoRs wiRes maY VaRY.

U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • WWW.HUSSMANN.COM
P/N 0524791_J
6
Canopy
ALWAYS*CLEAR™GLASS
Hussmann recommends using a soft cloth with
isopropyl (rubbing) alcohol to clean the inside
(coated) glass surface. Isopropyl alcohol does
not freeze and evaporates without leaving res-
idue. Always allow the surface to dry before
closing the door. Use of abrasives may dam-
age the coated surface and void the warranty.
Labels (stickers) applied to the coated surface
will cause damage and void the warranty.
LED LIGHT FIXTURES
LED (light emitting diode) lights work well
for dimming or on/off operation using an
occupancy sensor (optional kits). They can be
turned on and off in a cold environment with
no warm-up time and no negative impact on
lamp life.
CLEANING LED FIXTURES
Use a lint-free cloth to wipe the surface of
the luminaires. DoNoT use scouring pads,
bleach, solvents, or detergents. This may dam-
age the surface of the clear plastic cover.
Rail
Shelf

Hussmann Corporation • Bridgeton, Missouri 63044-2483 U.S.A.
LED Lighting Canopy, Shelf and Rail P/N 0524791_J
7
This instruction explains how to remove
original equipment manufactured (OEM)
uorescent lamp xtures and replace them
with Hussmann LED light xtures for multi-
deck merchandiser.
FOR YOUR SAFETY
• Read and observe all CAUTIONS and
WARNINGS shown throughout these
instructions.
• Each person working on or near the
installation described must wear safety glasses
or goggles.
• Block access to the work area by customers
or other personnel to prevent injury.
• Read and follow all industry safety
recommendations and established procedures.
• Wiring must be 2 wire with ground and rated
for 75°C (176°F).
ELECTRICAL CONNECTIONS
All wiring must be in compliance with NEC
and local codes. All electrical connections
are to be made in the wireway or mullion or
LED light xture.
IDENTIFICATION OF WIRING
Leads for all electrical circuits are identied by
colored plastic bands. These bands correspond
to the color code sticker (shown below) located
inside the merchandiser’s wireway cover.
Anthony doors may not conform to this chart.
Refer to the manufacturer’s manual for their
information.
GENERAL
WIRING COLOR CODE
Leads for all electrical circuits are identified by a colored plastic band:
neutral wire for each circuit has either White insulation or a White plastic
sleeve in addition to the color band.
Pink ........... RefRig. TheRmosTaT Low TemP. oRange oR
LighT BLue . RefRig. TheRmosTaT noRm TemP. Tan ...........LighTs
DaRk BLue . DefRosT TeRm. TheRmosTaT maRoon ....RecePTacLes
PuRPLe ....... conDensaTe heaTeRs YeLLow .....DefRosT heaTeRs 120V
BRown ....... fan moToRs ReD ..........DefRosT heaTeRs 208V
gReen*....... gRounD *eiTheR coLoReD sLeeVe oRcoLoReD insuLaTion
ELECTRICIAN NOTE: Use copper conductor wire only.
CASE MUST BE GROUNDED
These aRe maRkeR coLoRs wiRes maY VaRY.

U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • WWW.HUSSMANN.COM
P/N 0524791_J
8
SHIPPING DAMAGE
All equipment should be thoroughly examined
for shipping damage before and during unloading.
This equipment has been carefully inspected at
our factory. Any claim for loss or damage must
be made to the carrier. The carrier will provide
any necessary inspection reports and/or claim
forms.
Apparent Loss Or Damage
If there is an obvious loss or damage, it must
be noted on the freight bill or express receipt
and signed by the carrier’s agent; otherwise,
carrier may refuse claim.
Concealed Loss Or Damage
When loss or damage is not apparent until
after equipment is uncrated, retain all packing
materials and submit a written request to the
carrier for inspection, within 15 days.
Missing Parts
Every effort is made to ship all parts for the
kit. The Hussmann Service Center can be
reached by calling
• from U.S. & Canada 1-800-922-1919
• from Mexico 01-800-890-2900 •
REMOVE EXISTING FLUORESCENT
LIGHTING (if previously iNsTalleD)
1. Remove product from the merchandiser and
store at appropriate product temperature.
2. Turn the light switch to off. The switch is
located inside the case on the door mullion.
3. Lock out and tag out the circuit breaker for
the lighting circuit of the case where the LED
light xtures are being installed.
4. If uorescent lighting is present in the canopy
or shelves; it should be removed.
5. Remove and discard the lenses covering the
uorescent tubes.
6. Remove the uorescent tubes.
Fluorescent Lamp Disposal: The United States
Environmental Protection Agency has
information regarding environmentally-safe
uorescent lamp waste management programs.
Please visit the EPA website for more informa-
tion.
— LOCK OUT / TAG OUT —
To avoid serious injury or death from electrical
shock, always disconnect the electrical
power at the main disconnect when servicing
or replacing any electrical component. This
includes, but is not limited to, such items as
doors, lights, fans, heaters, and thermostats.

Hussmann Corporation • Bridgeton, Missouri 63044-2483 U.S.A.
LED Lighting Canopy, Shelf and Rail P/N 0524791_J
9
EcoShine ULTRA Canopy LED Lighting for Multi-Deck Merchandisers
Factory Replacement and Upgrade Parts
REVISION HISTORY
REV ECN DATE REVISION DESCRIPTION REV BY CHKD BY APPR BY
A ECN-NPD-0001922 2019/01/03 RELEASED FOR PRODUCTION IMG AGA AGA
B ECN-NPD-0002115 2019/05/07 CHANGED DIMENSION FROM 0.510
TO 0.540 AND 0.52 WAS 0.45 NBS MM JTN
APPROVED SOURCE OF SUPPLY UNIVERSAL LIGHTING TECHNOLOGY
LINE PART NUMBER REVISION DESCRIPTION LENGTH CCT POWER (W) POSITION
1 3089718 B LED-ES ULTRA CNPY 12IN 3000K 11.22 3000K 5.2 CANOPY
2 3089719 B LED-ES ULTRA CNPY 18IN 3000K 16.65 3000K 7.0 CANOPY
3 3089720 B LED-ES ULTRA CNPY 24IN 3000K 20.66 3000K 8.7 CANOPY
4 3089721 B LED-ES ULTRA CNPY 36IN 3000K 34.09 3000K 13.9 CANOPY
5 3089722 B LED-ES ULTRA CNPY 48IN 3000K 45.66 3000K 17.4 CANOPY
6 3089723 B LED-ES ULTRA CNPY 60IN 3000K 58.66 3000K 24.4 CANOPY
7 3089724 B LED-ES ULTRA CNPY 12IN 3500K 11.22 3500K 5.2 CANOPY
8 3089725 B LED-ES ULTRA CNPY 18IN 3500K 16.65 3500K 7.0 CANOPY
9 3089726 B LED-ES ULTRA CNPY 24IN 3500K 20.66 3500K 8.7 CANOPY
10 3089727 B LED-ES ULTRA CNPY 36IN 3500K 34.09 3500K 13.9 CANOPY
11 3089728 B LED-ES ULTRA CNPY 48IN 3500K 45.66 3500K 17.4 CANOPY
12 3089729 B LED-ES ULTRA CNPY 60IN 3500K 58.66 3500K 24.4 CANOPY
13 3089730 B LED-ES ULTRA CNPY 12IN 4000K 11.22 4000K 5.2 CANOPY
14 3089731 B LED-ES ULTRA CNPY 18IN 4000K 16.65 4000K 7.0 CANOPY
15 3089732 B LED-ES ULTRA CNPY 24IN 4000K 20.66 4000K 8.7 CANOPY
16 3089733 B LED-ES ULTRA CNPY 36IN 4000K 34.09 4000K 13.9 CANOPY
17 3089734 B LED-ES ULTRA CNPY 48IN 4000K 45.66 4000K 17.4 CANOPY
18 3089735 B LED-ES ULTRA CNPY 60IN 4000K 58.66 4000K 24.4 CANOPY
19 3089736 B LED-ES ULTRA CNPY 12IN 5000K 11.22 5000K 5.2 CANOPY
20 3089737 B LED-ES ULTRA CNPY 18IN 5000K 16.65 5000K 7.0 CANOPY
21 3089738 B LED-ES ULTRA CNPY 24IN 5000K 20.66 5000K 8.7 CANOPY
22 3089739 B LED-ES ULTRA CNPY 36IN 5000K 34.09 5000K 13.9 CANOPY
23 3089740 B LED-ES ULTRA CNPY 48IN 5000K 45.66 5000K 17.4 CANOPY
24 3089741 B LED-ES ULTRA CNPY 60IN 5000K 58.66 5000K 24.4 CANOPY
Part Numbers are subject to change.
Contact your Hussmann Rep. for replacement parts.

U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • WWW.HUSSMANN.COM
P/N 0524791_J
10
EcoShine ULTRA Horizontal LED Lighting
• Shelf and Rail for Multi-Deck
• Shelf, Rail and Canopy for Specialty and Service
Factory Replacement and Upgrade Parts
Part Numbers are subject to change.
Contact your Hussmann Rep. for replacement parts.
LED EcoShine ULTRA SHELF
ITEM PART NUMBER REV TITLE LENGTH
(CCT)
CORRELATED
COLOR TEMP
POWER
(W) POSITION
1 3133172 C LED-ES ULTRA SHLF 12IN 3000K 11.330 in 3000K 1.3 SHELF
2 3133173 C LED-ES ULTRA SHLF 12IN 3500K 11.330 in 3500K 1.3 SHELF
3 3133174 C LED-ES ULTRA SHLF 12IN 4000K 11.330 in 4000K 1.3 SHELF
4 3133175 C LED-ES ULTRA SHLF 12IN 5000K 11.330 in 5000K 1.3 SHELF
5 3133176 C LED-ES ULTRA SHLF 18IN 3000K 16.936 in 3000K 2.1 SHELF
6 3133177 C LED-ES ULTRA SHLF 18IN 3500K 16.936 in 3500K 2.1 SHELF
7 3133178 C LED-ES ULTRA SHLF 18IN 4000K 16.936 in 4000K 2.1 SHELF
8 3133179 C LED-ES ULTRA SHLF 18IN 5000K 16.936 in 5000K 2.1 SHELF
9 3133180 C LED-ES ULTRA SHLF 24IN 3000K 22.470 in 3000K 2.9 SHELF
10 3133181 C LED-ES ULTRA SHLF 24IN 3500K 22.470 in 3500K 2.9 SHELF
11 3133182 C LED-ES ULTRA SHLF 24IN 4000K 22.470 in 4000K 2.9 SHELF
12 3133183 C LED-ES ULTRA SHLF 24IN 5000K 22.470 in 5000K 2.9 SHELF
13 3133184 C LED-ES ULTRA SHLF 36IN 3000K 33.609 in 3000K 4.5 SHELF
14 3133185 C LED-ES ULTRA SHLF 36IN 3500K 33.609 in 3500K 4.5 SHELF
15 3133186 C LED-ES ULTRA SHLF 36IN 4000K 33.609 in 4000K 4.5 SHELF
16 3133187 C LED-ES ULTRA SHLF 36IN 5000K 33.609 in 5000K 4.5 SHELF
17 3133188 C LED-ES ULTRA SHLF 36IN 3000K HO 33.609 in 3000K 6.6 SHELF
18 3133189 C LED-ES ULTRA SHLF 36IN 3500K HO 33.609 in 3500K 6.6 SHELF
19 3133190 C LED-ES ULTRA SHLF 36IN 4000K HO 33.609 in 4000K 6.6 SHELF
20 3133191 C LED-ES ULTRA SHLF 36IN 5000K HO 33.609 in 5000K 6.6 SHELF
21 3133192 C LED-ES ULTRA SHLF 48IN 3000K 46.591 in 3000K 6.2 SHELF
22 3133193 C LED-ES ULTRA SHLF 48IN 3500K 46.591 in 3500K 6.2 SHELF
23 3133194 C LED-ES ULTRA SHLF 48IN 4000K 46.591 in 4000K 6.2 SHELF
24 3133195 C LED-ES ULTRA SHLF 48IN 5000K 46.591 in 5000K 6.2 SHELF
25 3133196 C LED-ES ULTRA SHLF 48IN 3000K HO 46.591 in 3000K 9SHELF
3133669/C
26 3133197 C LED-ES ULTRA SHLF 48IN 3500K HO 46.591 in 3500K 9SHELF
27 3133198 C LED-ES ULTRA SHLF 48IN 4000K HO 46.591 in 4000K 9SHELF
28 3133318 C LED-ES ULTRA SHLF 48IN 5000K HO 46.591 in 5000K 9SHELF
29 3133319 C LED-ES ULTRA SHLF 57IN 3000K 55.591 in 3000K 7.4 SHELF
30 3133320 C LED-ES ULTRA SHLF 57IN 3500K 55.591 in 3500K 7.4 SHELF
31 3133321 C LED-ES ULTRA SHLF 57IN 4000K 55.591 in 4000K 7.4 SHELF
32 3133322 C LED-ES ULTRA SHLF 57IN 5000K 55.591 in 5000K 7.4 SHELF
33 3133323 C LED-ES ULTRA SHLF 60IN 3000K 57.730 in 3000K 7.4 SHELF
34 3133324 C LED-ES ULTRA SHLF 60IN 3500K 57.730 in 3500K 7.4 SHELF
35 3133325 C LED-ES ULTRA SHLF 60IN 4000K 57.730 in 4000K 7.4 SHELF
36 3133326 C LED-ES ULTRA SHLF 60IN 5000K 57.730 in 5000K 7.4 SHELF
37 3133327 C LED-ES ULTRA SHLF 72IN 3000K 68.870 in 3000K 9SHELF
38 3133329 C LED-ES ULTRA SHLF 72IN 3500K 68.870 in 3500K 9SHELF
39 3133330 C LED-ES ULTRA SHLF 72IN 4000K 68.870 in 4000K 9SHELF
40 3133331 C LED-ES ULTRA SHLF 72IN 5000K 68.870 in 5000K 9SHELF
41 3133332 C LED-ES ULTRA SHLF 75IN 3000K 73.591 in 3000K 9.8 SHELF
42 3133333 C LED-ES ULTRA SHLF 75IN 3500K 73.591 in 3500K 9.8 SHELF
43 3133334 C LED-ES ULTRA SHLF 75IN 4000K 73.591 in 4000K 9.8 SHELF
44 3133335 C LED-ES ULTRA SHLF 75IN 5000K 73.591 in 5000K 9.8 SHELF