Huvitz CME-9000 User manual

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
Table of Contents
1. How to check SW version
2. Replacing Board
3. Replacing Cover
4. Sensor Position
5. Adjusting Clamp Power
6. Adjusting Wheel Position
7. Adjusting Size and Margin

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
1. How to check SW version

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
1. Checking SW Version
3) Check SW version
(GUI, MOTOR)
1) Select menu 2) Select User menu

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
2. Replacing Board

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
1. Open Cover
1) Loosen 2 bolts 2) Open the front cover
GUI Board
Motor Board
Power Board

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
2. Replace GUI board
1) Disconnect cables 2) Loosen 4 screws 3) Use original
FRAM to use original
setup data
Recommend to take a picture of setup data.(User
setup, Engineer mode) You can input them to new
GUI board
FRAM

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
3. Replace Motor board and Power board
1) Loosen 4 screws /
Disconnect cables for each
board
2) Replace board
Motor board Power board

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
3. Replacing Cover

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
1. Open Cover
1) Loosen 2 bolts 2) Open the front cover
GUI Board and
keypad board
Motor Board
Power Board

PRODUCT Auto Lens Edger SERVICE MANUAL
DOC No. SCS-I-9ME-091
PREPARE
REVIEW CONFIRM
DATE 2013.12.25
MODEL CME-9000
REVISION DATE
REVISON USE 2013.12.25
2. Remove GUI board and Keypad
1) Disconnect cables
2) Loosen 4 screws of
LCD. Remove LCD with
GUI board
Some cables are tied to cover. Cut cable ties if
necessary
3) Disconnect keypad 2 cables
4) Loosen 5 screws and remove Keypad board
5) Remove keypad