Huvitz Excelon CAB-4000 User manual

Excelon Operator’s Manual 1
Operator’s Manual
Excelon-Auto Blocker

2Excelon Operator’s Manual
IMPORTANT NOTICE
This product may malfunction due to electromagnetic waves caused by portable
personal telephones, transceivers, radio-controlled toys, etc. Be sure to avoid
having the above objects, which affect the normal operation of the product, brought
near the product.
The information in this publication has been carefully checked and is believed to be
entirely accurate at the time of publication. HUVITZ assumes no responsibility,
however, for possible errors or omissions, or for any consequences resulting from
the use of the information contained herein.
HUVITZ reserves the right to make changes in its products or product specifications
at any time without prior notice and is not required to update this documentation to
reflect such changes.
©2002 - 2003 HUVITZ Co., Ltd.
689-3, Geumjeong-dong, Gunpo-si, Gyeonggi-do,
435-862, Republic of Korea
All rights are reserved.
Under copyright laws, this manual may not be copied, in whole or in part, without the
prior written consent of HUVITZ Co., Ltd.

Excelon Operator’s Manual 3
Contents
IMPORTANT NOTICE.....................................................................................2
1. Introduction ...................................................................................................6
1.1 System Configuration.............................................................................6
1.2 Main Features .........................................................................................6
1.3 Classification...........................................................................................7
2. Safety Information.........................................................................................8
2.1 Introduction.............................................................................................8
2.2 Safety Symbols........................................................................................9
2.3 Environment factors.............................................................................10
2.4 Safety Precaution..................................................................................11
3. System Configurations.................................................................................16
3.1 Front View.............................................................................................16
3.2 Rear View ..............................................................................................16
3.3 StandardAccessory (Tool Box)............................................................17
4. Installation Procedure.................................................................................18
4.1 Installation.............................................................................................18
5. Operation......................................................................................................19
5.1 Frame Reader Module..........................................................................19
5.2 Blocker Module.....................................................................................22
5.2.1 Key functions...................................................................................23
5.2.2 Numeric value..................................................................................24

4Excelon Operator’s Manual
5.2.3 Job Management.............................................................................. 25
5.2.4 Command Menu.............................................................................. 28
5.3 Design of spectacles.............................................................................. 30
5.3.1 LAYOUT......................................................................................... 30
5.3.2 Edging ............................................................................................. 40
5.4 Blocking................................................................................................. 46
5.5 Usage for the different types of lenses................................................. 47
5.5.1 Optic lens......................................................................................... 47
5.5.2 Progressive lens including the Digital Scanning ............................. 50
5.5.3 Bi-focal lens including the Digital Pattern ...................................... 53
5.5.4 Auto recognition of lens type........................................................... 57
6. User Menu ................................................................................................... 58
6.1 System Info............................................................................................ 59
6.2 Basic Info............................................................................................... 60
6.3 LAYOUT DEF ...................................................................................... 62
6.4 EDGING DEF....................................................................................... 64
6.5 LENSMETER DEF.............................................................................. 69
7. Factory Menu.............................................................................................. 70
7.1 Blocker .................................................................................................. 70
7.2 Lensmeter.............................................................................................. 71
7.3 EEPROM .............................................................................................. 72
8. Calibration Menu ........................................................................................ 73
8.1 Lensmeter.............................................................................................. 74
8.2 Blocker .................................................................................................. 75

Excelon Operator’s Manual 5
8.3 TRACER ...............................................................................................76
8.4 TRACER-SIM.......................................................................................77
9. Maintenance ................................................................................................77
9.1 “It is needed to setup prism” message.................................................77
9.2 “Remove the object on the table and then turn off/on” message......79
9.3 Blocking Position calibration...............................................................79
9.4 Blocking axis calibration......................................................................80
9.5 Calibration of the internal lensmeter’s center....................................81
9.6 Calibration of the internal lensmeter’s axis........................................83
9.7 Touch Panel calibration........................................................................84
9.8 Miscellaneous........................................................................................85
Specification.....................................................................................................87

6Excelon Operator’s Manual
1. Introduction
1.1 System Configuration
•Auto Blocker (CAB-4000)
This product is Auto Blocker CAB-4000, lenses can be checked and blocked in
automatically. So the CAB-4000 eliminates the need for manual inspection and blocking of
the lens. Also, with the CAB-4000 a frame can be read in simple step.
1.2 Main Features
•This can block all kinds of lenses in which include the normal lens without 3 dot,
the bi-focal lens, the multi-focal lens and the lens with 3 dot.
•TFT-LCD (8.4”) True color display device and touch screen are harmonized to
offer the maximum convenience for everyday use
•Frame Reader Module reads a frame as well as a pattern, and then sends it to the
main GUI display module.
•This includes not only the image processing module but also the lensmeter
module so that it can block from a normal lens without 3 dot to a multi-focal lens.
•We can design all information for the layout and the edging at one page, and send
it to other two edger machines.
•Graphically Designed Test Mode enables the operator to effectively perform the
routine maintenance without the technical assistance
•Any shape and material of a frame from rimless to goggles are automatically and
precisely scanned with 3D technology ensuring no margin of error

Excelon Operator’s Manual 7
•The Digital Scanning technology can scan a frame shape for a demo lens without
a conventional tracer. This provides you an enormous convenience and a time
saving.
•A maximum one thousand of frames are memorized in the permanent memory.
Therefore, users can retrieve them whenever they want.
•The compete harmony between this blocking machine and edger machines can
accomplish the full automation in the edging processes.
1.3 Classification
•Protection against electric shock: Class I(earthed)
•Installation Category: II
•Pollution Degree: 2

8Excelon Operator’s Manual
2. Safety Information
2.1 Introduction
Safety is everyone’s responsibility. The safe use of this equipment is largely
dependent upon the installer, user, operator, and maintainer. It is imperative that
personnel study and become familiar with this entire manual before attempting to
install, use, clean, service or adjust this equipment and any associated accessories.
It is paramount that the instructions contained in this manual are fully under stood
and followed to enhance safety to the patient and the user/operator. It is for this
reason that the following safety notices have been placed appropriately within the
text of this manual to highlight safety related information or information requiring
special emphasis. All user, operators, and maintainers must be familiar with and pay
particular attention to all warning and cautions incorporated herein.
“Warning” indicates the presence of a hazard that could result in severe
personal injury, death or substantial property damage if ignored.
“Note” describes information for the installation, operation, or maintenance of
which is important but hazard related if ignored.
“Caution” indicates the presence of a hazard that could result in minor injury,
or property damaged if ignored.
!WARNING
!CAUTION
!NOTE

Excelon Operator’s Manual 9
2.2 Safety Symbols
The International Electro technical Commission (IEC) has established a set of
symbols for medical electronic equipment, which classify a connection or warn of any
potential hazard. The classifications and symbol s are shown below.
Save these instructions
I and O on power switch represent ON and OFF
respectively.
This symbol identifies a safety note. Ensure you understand
the function of this control before using it. Control function is
described in the appropriate User’s or Service Manual.
Identifies the point where the system safety ground is
fastened to the chassis. Protective earth connected to
conductive parts of Class I equipment for safety purposes.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is
attached to a product it means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products should be
disposed of separately from the municipal waste stream
via designated collection facilities appointed by the
government or the local authorities.
3. The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your
old appliance, please contact your city office, waste
disposal service or the shop where you purchased the
product.

10 Excelon Operator’s Manual
2.3 Environment factors
Avoid the following environments for operation or storage:
Where the equipment is exposed to water vapor.
Don’t operate the equipment with a wet hand.
Where the temperature changes extremely.
- Operation Temperature: 10~40°C
(Humidity : 50 ~ 80%)
- Storage Temperature : -20 ~ 85°C (Humidity: 50 ~ 80%)
Where the humidity is extremely high or there is a ventilation
problem.
Where equipment is exposed to chemical material or
explosive gas.
Where the equipment is exposed to direct sunlight.
Where it is near the heat equipment.
Don’t disassemble the product or open. We aren’t
responsible for it for nothing.

Excelon Operator’s Manual 11
Don’t plug the AC power cord into the outlet before the
connection between devices of the equipment is
completed. This can generate the defect.
Where the equipment is subject to excessive shocks or
vibrations.
Be careful not to be inserted dust, especially, metal
Be careful not to close the fan located on the lateral or
backside of the equipment.
Pull out the power cord with holding the plug, not the cord.
Avoid places where the ambient temperature falls below 10℃or exceeds 40℃for
normal operation, or below –20℃or exceeds 85℃for transportation and storage.
Humidity should be maintained between 50% and 80% for normal operation,
transportation and storage. Avoid environments where the equipment is exposed to
excessive shocks or vibrations. And also the normal operation time is as following:
operation time : short term operation max 1min
2.4 Safety Precaution
This equipment has been developed and tested according to safety standards as
well as national and international standards. This guarantees a very high degree of
safety for this device. The legislator expects us inform the user expressively about
the safety aspects in dealing with the device. The correct handling of this equipment
is imperative for its safe operation. Therefore, please read carefully all instructions
before switching on this device. For more detailed information, please contact our

12 Excelon Operator’s Manual
Customer Service Department or one of our authorized representatives.
①This equipment must not be used (a) in an area that is in danger of explosions
and (b) in the presence of flammable, explosive, or volatile solvent such as
alcohol, benzene or similar chemicals.
② Do not put or use this device in humid rooms. Humidity should be maintained
between 50% and 80% for normal operation. Do not expose the device to water
splashes, dripping water, or sprayed water. Do not place containers containing
fluids, liquids, or gases on top of any electrical equipment or devices.
③ The equipment must be operated only by, or under direct supervision of a
properly trained and qualified person.
④ The service technician of Huvitz or the technician authorized by Huvitz may only
carry out modifications of this equipment.
⑤ Customer maintenance of this equipment may only be performed as stated in the
User’s Manual and Service Manual. Any additional maintenance may only be
performed by the service technician of Huvitz or the technician authorized by
Huvitz.
⑥ The manufacturer is only responsible for effects on safety, reliability, and
performance of this equipment when the following requirements are fulfilled: (1)
The electrical installation in the respective room corresponds to the specifications
stated in this manual and (2) This equipment is used, operated, and maintained
according to this manual and Service Manual.
⑦ The manufacturer is not liable for damage caused by unauthorized tampering
with the device(s). Such tampering will forfeit any right to claim under warranty.
⑧ This equipment may only be used together with accessories supplied by Huvitz.

Excelon Operator’s Manual 13
If the customer makes use of other accessories, use them only if their safe
usability under technical aspect has been proved and confirmed by Huvitz or the
manufacturer of the accessory.
⑨ Only person who has undergone proper training and instructions are authorized
to install, use, operate, and maintain this equipment.
⑩ Keep the User’s Manual and Service Manual in a place easily accessible at all
times for persons operating and maintaining the equipment.
⑪ Do not force cable connections. If a cable does not connect easily, be sure that
the connector (plug) is appropriate for the receptacle (socket). If you cause any
damage to a cable connector(s) or receptacle(s), let the damage(s) be repaired
by an authorized service technician.
⑫ Please do not pull on any cable. Always hold on to the plug when disconnecting
cables.
⑬ Before every operation, visually check the equipment for exterior mechanical
damage(s) and for proper function.
⑭ Do not cover any ventilation grids or slits. Immediately turn off and unplug any
equipment that gives off smoke, sparks, strange noises, or odors.
○
15 Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
○
16 Don’t move your hands into the working area during blocking, otherwise you may
get a damage in your hands.
○
17 Keep to use LAN Port only in the inside building.
○
18 This machine might be impaired if used in a manner not specified by

14 Excelon Operator’s Manual
manufacturer and this manual.
`
•Be sure not to move the hands into the working area during blocking.
Otherwise, the person may be seriously hurt.
•Be sure not to block without a block in the block holder, otherwise the lens may
be broken or scratched.
•Be sure not to block when there is no lens on the lens supporter. Otherwise it
may cause the malfunction of the product.
•The equipment should be properly installed and operated based on the
instructions on this manual. If the power is turned on without unlocking the
locking device like several styrofoams, it may cause the damage to the product
and cause the malfunction of the product.
•Do not disassemble the product without the proper training. It may cause the
electric shock, serious hurt during the operation or cause the malfunction of the
product.
•Be sure the material of lens is matched with the job options selected in the
display before starting the edging mode. Otherwise, it may cause the damage
to the wheel and shorten the lifetime of wheel.
•The safety beveling for glass lenses should be performed both at front and rear
side. Otherwise, it will cause the damage to the human skin.
•The product should be properly installed and maintained at the horizontally
leveled place. Otherwise, it may affect the normal operation of the product.
!WARNING

Excelon Operator’s Manual 15
•Be sure that the stylus of frame reader is not interfered with the human body or
other objects during the operation. Otherwise, it may cause the hurt or
malfunction of the product.
•Do not force on the stylus of frame reader. It may cause the malfunction of the
product.
•In case of setting down the equipment, make sure not to be interfered with the
obstacles. Setting down the product slowly in order to prevent the hurt of human
body or damage to the product.
•When moving the equipment, make sure the locking device and the screw for
the cover are properly tightened.
•In case of packaging the equipment, use the recommended packaging material
and method in order to prevent the damage during the transportation.
•Be sure to use the standard accessories or tools provided together with the
product for the maintenance. Otherwise, it may cause the malfunction of the
product.
.
!CAUTION

16 Excelon Operator’s Manual
3. System Configurations
3.1 Front View
3.2 Rear View
Main display window
Main Key Pad
Frame
Reader
Module
Lens Supporter
Blocking Arm
Key for
Frame Reader
Main Power Input Fan

Excelon Operator’s Manual 17
3.3 Standard Accessory (Tool Box)
•Only Use 3M LEAP-III™as the Block Tape in order to assure the proper axis
positioning.
•In case of Super Hydrophobic Lens, use the specialized sticker in order to
assure the proper axis position.
Pattern HolderStandard Pattern
Standard Frame
!NOTE
Lens Supporter Lens Supporter
for Frame Change
Lens Supporter
For Digital Scanning
Touch Pen

18 Excelon Operator’s Manual
4. Installation Procedure
4.1 Installation
① Remove the shock-absorbing material from the packing box and pull out the auto
blocker carefully.
② Remove the shock-absorbing material from the blocking arm and the workspace
of Stylus.
③ Plug the Power Cable into the receptacle at the back of the product and turn on
the power to check the initial operation.
④ If the initial operation works properly, connect Edger and Auto blocker by using 9-
pin D-sub Crossed Interface Cable.
•Be sure to check the voltage selector underneath of the product before the
power switch is ON.
•Be sure that the edger system of our company should be set to the blocker type.
Otherwise, the transmitted data could be incorrect. Our edging system provides
internally two type of external devices which are a tracer and a automatic
blocker.
!CAUTION

Excelon Operator’s Manual 19
5. Operation
5.1 Frame Reader Module
•MATERIAL
-Select one of METAL, PLASTIC or OPTYL.
-Before the frame is traced, choose one of the above items.
-The specified values are used in Edger for the size adjustment.
☞If the pattern or the demo lens are placed in the frame reader module, it
automatically detects which one is placed on it.
•BOTH
-Press this button for two eye tracing. This is only for frame tracing.
☞Usually one side tracing is used for the pattern or a demo lens.
•RIGHT
-Press this button for right eye tracing.
•LEFT
-Press this button for left eye tracing.
☞The one side traced data for pattern or a demo lens is copied symmetrically to the
other side.
•STOP
-Press this button to stop tracing.
BOTH MATERIAL STOP RIGHT LEFT

20 Excelon Operator’s Manual
Operation Tips
•Refer to the messages for the frame reader module which are shown the top of
main display with beep sound. These messages enable you to take a next
action.
•The data will be automatically transmitted after finishing the tracing.
•In case that the single side (R or L) is traced, the traced data will be
automatically duplicated symmetrically to the other side to complete the job.
•Semi-Automatic Tracing Mode will be executed in case of pressing one of these
three buttons, ‘L’, ‘B’ or ‘R’ for more than 3 seconds. It will be useful to trace the
frame with the lopsided groove.