Hyco SUN PRINCE SP1000E User manual

SUN PRINCE
QUAR Z HEA ER
SP1000E, SP1500E, SP2000E, SP3000E, SP4000E, SP4500E, SP6000E
Instruction Manual
Power Supply: 230V ac
Frequency: 50 Hz
6. GUARAN EE AND SERVICE POLICY
The Hyco Sun Prince uartz Heater is supplied with a standard 2 year replacement
warranty (excluding Lamps) that protects against any manufacturing defects up for up
to 2 years of the original purchase date. In the event of a product failure please
contact Hyco on 01977 517555. Incidental or consequential damages are excluded
from this warranty.
5. SPECIFICA IONS
Hyco Manufacturing Ltd
California Place
California Drive, Whitwood
Castleford
West Yorkshire
WF10 5 H
Tel: [phone] Fax: [phone]
Web: www.hyco.co.uk
E-mail: [e-mail]
MODEL POWER SPARE LAMP
SP1000E 1kW L1000V
SP1500E 1.5kW L1500V
SP2000E 2kW L2000V
SP3000E 3kW 2xL1500V
SP4000E 4kW 2xL2000V
SP4500E 4.5kW 3xL1500V
SP6000E 6kW 3xL2000V
Version 1.0 March 2007
EYK0716 SUNPRICE MANUALv7:EYK0716 SUNPRICE MANUAL 30/4/07 16:49 Page 1

HYCO SUN PRINCE QUAR Z HEA ER
SP1000E, SP1500E, SP2000E, SP3000E, SP4000E, SP4500E, SP6000E
Thank you for purchasing the Hyco Sun Prince uartz Heater. This heater uses
radiant heat to warm objects and people directly, making it ideal for draughty,
hard - to heat situations such as workshops, warehouses. An RCD circuit
breaker is strongly recommended. Please read and understand these
instructions before commencing installation, and leave them with the user
when installation is complete.
1. SAFE Y
he installation must be carried out by a competent person in accordance
with current Building Regulations. he Electrical Installation must be
carried out by a qualified electrician in accordance with the current
edition of the I.E.E. Wiring Regulations.
• Only connect the heater to a single phase supply with a mains voltage as specified
on the rating plate.
• The heater must be positioned at a minimum height of 2m and at a distance of at
least 1m from the nearest object that would be exposed to heat radiation..
• The heater is not suitable for mounting on highly flammable surfaces.
• The heater must be mounted onto a solid surface.
• If the cord of this appliance (not supplied) is damaged, discontinue use of this
product and arrange for a competent person to replace it.
• Do not let animals or children touch or play with the heater. Please note that the
heater gets very hot during operation.
• Do not cover the heater as this may cause overheating.
• Take particular care with moveable items such as curtains.
• Do not use the heater without the safety guard fitted or if the safety guard is
damaged.
• The Sun Prince heaters are not suitable for outdoor use or in damp conditions.
Avoid contact with water.
2. INS ALLA ION
When choosing the location for mounting the Sun Prince, ensure that you
have followed the safety instructions and recommendations.
• The bracket is supplied in two parts: Part A mounts to the wall using the wall
plugs and screws provided and Part B holds the heater and joins to Part A
(see Fig 1 below).
• Part A of the bracket should be mounted (ideally with the aid of a spirit level) to
the chosen surface using the wall plugs and screws provided.
• Part B of the bracket should then be fixed to Part A by lining up the holes and
securing using the bolt and lock nut provided.
• The heater is then positioned so that the centre hole on the side panel lines up
with the slot on the bracket and secured into place using the black knobs
provided. See diagrams below for guide to mounting the various models.
3. ELEC RICAL INS ALLA ION
• The electrical connection should be made to the fixed wiring of the property
using appropriately rated cable and a double pole isolator switch should be used.
Electrical Installation should be carried out by a competent person according to
the current edition of the I.E.E.Wiring Regulations.
• Please note that an inrush current of several times the steady state current will
flow for a few hundredths of a seconds after first switching on. PIR devices or
other controllers may be used to control this unit provided all devices are rated
to the appropriate electrical loading with due allowance for in-rush current.
• This unit MUST be earthed and wired with heat resistant cable.
• When fitting/replacing the quartz lamp: Do not touch the lamp with bare
hands. Use a soft cloth/tissue to hold the lamp.
• Remove the back plate to gain access to the terminal block.
• Take the front guard off by removing the four screws holding the tabs in place.
Thread the lamp wires through the holes at either side of the lamp holders and
pull through from the back.
• Locate either side of the lamp into the holders and ensure it is held securely.
• Connect the lamp wires to the spade connectors on the Live and
Neutral terminals.
• Secure the back plate.
• Replace the guard.
CAU ION!
Do not attempt to adjust or touch the heater until it has cooled down
and the power is disconnected.
4. CLEANING AND MAIN ENANCE
• Before cleaning, ensure the heater is disconnected from the power and that it has
cooled completely.
• Wipe the exterior of the heater with a damp cloth.
• Do not use abrasives or chemical cleaners to clean the heater.
• If the interior requires cleaning, use a soft, dry cloth taking care not to touch the
quartz lamp with bare hands.
B
A
Fig 1
EYK0716 SUNPRICE MANUALv7:EYK0716 SUNPRICE MANUAL 30/4/07 16:49 Page 4