HYSUN W2 User manual

Wallbox EV Charger
W2 User Manual
REGRAHCVE

N14-50P
REGRAHCVE
- 1 -
01/Product Overview
Installation Kits Tool
Hanging board×1
M3*6mm×1
Hook×1
Hex key×1
KA4*30mm×4 KA4*40mm×2

- 2 -
02/Technical specifications
General
Dimensions 200mm x 200mm x 65mm
（L*W*H)
Wall mounting Operation
Temperature -40°C~+55°C
Weight 4KG
Charging
Charging power 7kW
Charging Plug GBT (GB/T 20234.3-2015)
Power Supply 1phase (7kW)
Voltage 230Vac (±10 %)
Mains frequency 50/60 Hz
Connectivity
Built-in eSIM
WiFi 2.4Ghz connection
Control charging via X smart App
RFID reader
OCPP 1.6
Dynamic Load Balancing CT
MID meters

- 3 -
03/Protection
•Integrated protection for open / break fault condition in supply PEN conductor
according to BS 7671:2018/A1:2020
•Built-in RCD for ground fault protection (30 mA AC/ 6 mA DC) according
to EN 61008-1 and IEC 62955
Degree of protection IP65
Impact resistance IK10
Insulation class I
Overvoltage category III
Control Box Size: L200 x W200 x H65mm
Cable Length: 4.5Meter / Customized
Inner Box: L300 x W300 x H150mm
Outer Carton: L340 x W340 x H330mm
Dimension & Package

- 4 -
04/Important Safety Instructions
1. Ensure that the equipment is well grounded before powering it on.
2. Keep the charging gun head clean and dry. If it gets dirty, wipe it with a clean and
dry cloth.
3. Do not touch the charging gun with your hands while charging.
4. Make sure that the input voltage, frequency, circuit breaker, or fuse of the device
and other conditions meet the specifications before powering on the equipment.
5. Insulate all tools as necessary to prevent bare metal parts from touching the
metal frame and causing a short circuit.
6. Do not attempt to disassemble, repair or modify the charging pile. If
maintenance or modification is necessary, contact the staff. Improper operation
can result in equipment damage, water leakage, leakage, and other hazards.
This equipment should be installed, adjusted, and serviced by qualified electrical
personnel familiar with the construction and operation of this type of equipment
and the hazards involved.
7. The equipment should be operated in a clean, constant temperature, and
constant humidity environment as much as possible, and the operating
environment must not contain volatile gases or flammable gases.
8. Charge with caution during rain and thunder.
9. Follow the instructions strictly during use. Do not allow children to get close to
or use the charging pile while charging to avoid injury.
10. After charging is complete, hang the charging gun properly back into the
charging gun base. Avoid placing the charging gun head at random or dropping it
on the ground to prevent safety accidents

- 5 -
1. Use the BIGGER plate to mark
the location of the screw holes on
the wall where you plan to mount
the station.
3.Hammer the plastic bolts into the
holes you drilled.
2.Use a drillto make holes in
the wall where you marked the
locations.
WARNING: Turn off the power before you begin the Installation. Use extrem
caution and follow Instructions carefully.
05/Installation instructions
1.Drilling
1
3
2

- 6 -
1.Fix the BIGGER plate to the wall
using screws.
3.Lock the bottom anti-sheft
SMALLER plate with screws.
4.Hang the WALLBOX station on the
plate that is now affixed to the wall.
2.Hang the WALLBOX station on
the plate that is now affixed to the
wall.
REGRAHCVE
REGRAHCVE
REG
RAHCVE
2.Mounting
1
3 4
2

REGRAHCVE
- 7 -
06/Features
2.RFID area
The aintegrated RFID reader enables access control of the Charger
and identification of different users.
The light strip communicates the status of the Charger at all times.
1.Display screen
3.Indicator light
4.Emergency stop button
6.Charging Plug
5.NEMA 14-50
07/Charging interface
Working State Red Green Blue
PowerOn (Unplugged) / Stays On /
Insert the plug (Uncharged) / / Stays On
Charging Mode //Flashihg
Charging Completed / / Stays On
Metering communication error Stays On / /
Under-voltage alarm Stays On / /
Over-voltage alarm Stays On / /
Groundfault Stays On / /
Over current protection Stays On / /
Leakage protection Stays On / /
Overtemperature protection Stays On / /
RFID failure Stays On / /
Relay failure Stays On / /
Memory failure Stays On / /
• Remarks： Fault reason will display on LCD screen when RED indicator
stays on.
N14-50P

Customer Support
For Technical Assistance Call:
T: 0086-180-254-31819
E: [e-mail]
For additional products and information, please visit our website at:
www.hysunpower.com.