iBaby M3s User manual

iBaby Monitor
Model: M3s
User Manual

2
2
Index
1Introduction ....................................................................................................................3
1.1 The package contents ........................................................................................3
1.2 Product Features ................................................................................................3
1.3 Product Specifications ........................................................................................4
2Appearance and Interface .............................................................................................5
2.1 Appearance.........................................................................................................5
2.2 Back of the camera.............................................................................................5
3Set-up and Installation...................................................................................................6
4Troubleshooting .............................................................................................................7
4.1 No Connection (Error: No Camera Available) ....................................................7
4.2 No Wi-Fi Connection within LAN/Wi-Fi (Error: No Wi-Fi available) ...................7
4.3 Your iBaby Monitor is not connected. Please try again.(errorCode:-1101)….,…8
4.4 Your iBaby Monitor is not connected. Please try again.(errorCode:-1019)…..…8
4.5 iBaby monitor connects to Wi-Fi but has an unstable connection……………….9
4.6 Audio is enabled but I cannot hear my baby. ........................................................8
4.7 Audio is enabled but I receive a static sound........................................................9
5FAQ................................................................................................................................9
5.1 General Usage....................................................................................................9
5.2 Set-up and Installation......................................................................................10
5.3 Product Features ..............................................................................................12
5.4 Returns and Exchanges ...................................................................................15
6. FCC Caution ..................................................................................................................15

3
3
1 Introduction
The iBaby monitor works with your iPod touch, iPhone or iPad so you can see and hear
your baby anytime, anywhere as long as you are connected to the internet (including Wi-
Fi, 3G/4G network, etc.). From your free app, you set motion/sound alerts, zoom in and
snap photos so you never miss an important moment.
"This product is meant for providing convenience for baby monitoring. The manufacturer is
not responsible for any legal liability caused by negligence. "
1.1 The package contents
1 Camera
1 Power Adapter
1 Bracket
1 Antenna
1 Quick Installation Guide
1 Screw Set
1.2 Product Features
Supports 802.11b/g/n protocol for wireless monitoring.
It works on TCP/IP network protocols.
Users can browse video with an iPod Touch, iPhone and iPad.
Built-in two-way hi-definition microphone and speaker.
Infrared LED lights for night vision within 19 feet range and provides 24 hours
monitoring.
The monitor rotates 350° horizontally and 70° vertically.
The internal speakers enable users to capture sound and motion in the room.
Stores up to 100 alerts in Alert Gallery.
Photos are stored on the app or iBaby cloud service.
Supports UPNP, P2P, and port forwarding automatically on the router.

4
4
1.3 Product Specifications
Item
Sub Item
Description
Image Capture
Sensor
CMOS sensor
Total of Pixel
300k
Lens
f=3.6mm, F=2.0,Fixed Iris
Pan/Tilt
Pan Coverage
350°
Tilt Coverage
70°
Lighting
Lights
10pcs 850nm Infrared LED lights, 5m
distance
Lighting Control
Auto control
Video and Audio
Resolution
640×480 (VGA) 320×240 (QVGA) 160×120
(QQVGA)
Compression
MJPEG
Frame Rate
≤30fps
Bit Rate
128kbps
Audio Compression
ADPCM
Network
Basic Protocol
TCP/IP, UDP/IP, HTTP, DHCP, P2P
Other Protocol
802.11b/g/n
Other Features
Video Control
Available
Two-way Audio
Available
Motion Detection
Available
Sound Detection
Available
Upgrade
Upgrade from network
Hardware Interface
Audio In
Internal Microphone
Audio Out
Build-in Speaker
Physical Index
Weight
0.78 lb (estimate)
Main body
4.37 in (L)*4.3 in (W)*4.96 in (H)
Power
DC 5V 1.5A
Power consumption
<6W
Operating temperature
0℃~ 40℃
Operating humidity
10% ~ 80% non-condensing
Software(iPod Touch ,
iPhone and iPad)
iOS 6.0 or later
Android 2.2 or later
iBaby View app is free to download from
App Store or Google Play

5
5
2 Appearance and Interface
2.1 Appearance
2.2 Back of the camera
1 Power Input Socket: Connect Power adaptor, the adaptor‘s output is 5V 1.5A.
2 Wi-Fi Antenna Connector: Install the Wi-Fi antenna here.
3 RJ45 Ethernet Socket: The spare LAN cable connector.
4 PWR Lys: Indikerer at strømmen er på.
5 NET Light: Indicates that the monitor is connected to server. But If the NET light
flashes slowly, it indicates that the iBaby monitor is disconnected from server. If the
NET light flashes quickly, it indicates that the iBaby monitor is connecting to server.
6 USB Connector: Connects the camera with an iOS device with USB cable.
2
3
1
4
5
6

6
6
3 Set-up and Installation
a. Ensure your Apple iOS device is connected to your Wi-Fi network.
b. From the App Store, download “iBaby View App” on to your supported
mobile device.
c. Plug the power adapter into the camera and into an electrical outlet.
d. The camera will take a minute to power on with a “beep” sound.
e. Connect the USB cable from your mobile device to the camera.
f. The message “Share Wi-Fi Settings” will appear. Please select “Allow”.
g. The message “iBaby would like to communicate with the iBaby Monitor”
will appear. Please select “Allow”
h. Proceed to follow the simple onscreen instructions to complete the setup.

7
7
4 Troubleshooting
4.1 No Connection (Error: No Camera Available)
a. Place the monitor within 75 feet of your wireless router to ensure a strong Wi-Fi signal.
b. Reboot the router by unplugging the power adapter from the wall outlet for 10 seconds.
Once the router is powered on, wait for all indicating lights and symbols on the router
to turn on. Proceed to setup the monitor.
c. Reboot the monitor by turning off the camera for 10 seconds and then powering it back
on.
4.2 No Wi-Fi Connection within LAN/Wi-Fi (Error: No Wi-Fi available)
a. Ensure your iOS device is connected to your Wi-Fi network.
b. Check if the USB cable is properly connected to the iBaby monitor and your mobile
device.
c. Place the monitor within 75 feet of your wireless router to ensure a strong Wi-Fi signal.
d. Reboot the router by unplugging the power adapter from the wall outlet for 10 seconds.
Once the router is powered on, wait for all indicating lights and symbols on the router
to turn on. Proceed to setup the monitor.
e. If the above solutions do not solve the problem, please contact Customer Service at
[e-mail]
4.3 Your iBaby Monitor is not connected. Please try again.(errorCode:-
1101)
a. Make sure your iBaby monitor is using the same Wi-Fi network as your iOS device.
b. If the NET light flashes slowly, it suggests that the Baby monitor is disconnected from
server. You need to turn off the power and restart the monitor.
4.4 Your iBaby Monitor is not connected. Please try again.(errorCode:-
1019)
a. Make sure your iBaby monitor is using the same Wi-Fi network as your iOS device.
b. iBaby monitor does not support 5G Wi-Fi; it only supports 2.4G Wi-Fi.
c. Place the monitor within 75 feet of your wireless router to ensure a strong Wi-Fi signal.

8
8
d. Login to your router, and check your Wi-Fi settings (e.g.Netgear).
Check SSID (Wireless Network Name/SSID cannot contain any symbols, characters
or spaces. ONLY numbers, letters, and -).
For Security Mode, select WPA/WPA2.
Change the Wi-Fi channel to reduce signal interference.
Cancel MAC address filter on router.
4.5 iBaby monitor connects to Wi-Fi but has an unstable connection
a. Place the monitor within 75 feet of your wireless router to ensure a strong Wi-Fi signal.
b. Reboot the router by unplugging the power adapter from the wall outlet for 10 seconds.
Once the router is powered on, wait for all indicating lights and symbols on the router
to turn on. Proceed to setup the monitor
c. If the above solutions do not solve the problem, please contact Customer Service at
[e-mail]
4.6 Audio is enabled but I cannot hear my baby.
1) Increase the volume on your mobile device.
2) For the best sound transmission, place the monitor within 5 feet of the baby.

9
9
3) If your Wi-Fi network is weak, this can affect sound streaming and transmission.
4) You can try to restart the monitor.
5) If the above solutions do not solve the problem, please contact Customer Service at
[e-mail]
4.7 Audio is enabled but I receive a static sound.
1) Please make sure the distance between the mobile device and the camera is within10
feet.
2) Do not place the camera near any other electronic devices.
3) You can try to restart the monitor.
4) If the above solutions do not solve the problem, please contact Customer Service at
[e-mail]
5 FAQ
5.1 General Usage
1) What iOS devices are compatible with the iBaby monitor?
The iBaby monitor is compatible with the following devices:
iPod Touch 4th Generation and later, iPhone 4 and later, iPad 2 and later, and iPad mini.
All iOS devices must be iOS 6.0 and later
2) Do I need an app to view my baby?
Yes! You can download the iBaby View App from the App store on your iOS device.
3) Can the iBaby monitor detect motion?
Yes. You can select the motion alert icon in your app. If there is any motion, the camera
will detect it and trigger the alert to ring.
4) Does the iBaby monitor detect sound?
Yes. You can select the sound alert icon in your app. If there is any sound, the camera will
detect it and trigger the alert to ring.

10
10
5) How many users can use the iBaby monitor?
An unlimited number of users can access the iBaby monitor; however, only four users can
access the monitor simultaneously.
5.2 Set-up and Installation
1) What function does the USB connection on the back of the iBaby
Monitor serve?
During the installation process, the USB cable must connect your mobile device to the
iBaby monitor to successfully complete the Wi-Fi setup.
2) What is the recommended distance between the iBaby monitor and
the router?
Keep the iBaby monitor within 75 feet of your router to ensure a strong Wi-Fi signal and a
reliable connection.
3) What do signal frames on the video screen mean?
The signal frames display the signal strength between the camera and a router.
One signal strength bar means the strength is poor and the monitor will not
function properly. Two signal strength bars mean the strength is ok and there
will still be issues functioning properly. Three signal strength bars indicate the
strength is good and the monitor will function normally with the fullest strength.