iBeam TE-WKMR43 User manual

©COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
iBEAMUSA.comiBEAM Vehicle Safety Sytems ®REV. 07/20/2020 INSTTE-WKMR43
Attention! When testing the aftermarket
equipment, ensure that all factory equip-
ment is connected before cycling the key to
ignition.
TE-WKMR43
INSTALLATION INSTRUCTIONS
#IBEAMSAFETY
Installation............................................................2-3
Wireless Pairing.....................................................4
Display Settings .....................................................5
Wire Lenths ............................................................6
Specifications.........................................................7
TABLE OF CONTENTS
TOOLS REQUIRED
• Wire stripper
• Tape
• Digital Multi-meter
• Cutter
Universal Wireless 4.3” Mirror/Monitor
and Camera
Visit iBEAMUSA.com for more detailed informatuon about the product and up-to-date vehicle specific
applications.
Product Features
• Wireless camera and mirror/monitor kit
• 4.3” LCD Monitor
• 20 M / 65 FT range
• DC socket for monitor power with USB for smart device charging
• Video triggered by the camera’s signal
Part Components
A) Mirror/Monitor B) Camera w/ dual mounting options C) Accessories
A B C

386-257-1187
|
iBEAMUSA.com
2
Mirror/Monitor install and wiring
1. Carefully extend the clips on the back
of the clip-on mirror and attach to the
current rearview mirror in the vehicle.
2. Plug the DC socket into the mirror and
run the wire in the path shown in Figure
A and safely hide the wire from being
pulled or caught on while operating the
vehicle.
4. Plug the DC socket into the socket in
the vehicle. There is an additional USB
port on the back of the DC socket so
smart device charging can still be done.
(Figure B)
NOTE: If your vehicle DC socket has power
while the vehicle is powered down, you may
need to unplug the monitor while parked so
the battery does not discharge.
Figure A Figure B
2 Amp Charging port
1
MONITOR INSTALLATION

REV. 07/20/2020 INSTTE-WKMR43 3
CAMERA INSTALLATION
Camera Installation
1. Mount the camera with either the surface
mount or the license plate mount. If
wanting the surface mount, the two
small screws will need to be removed
to remove the license plate mount and
replace with surface mount.
2. Remove the tail light from the vehicle
to allow access to the light bulbs wiring.
(If help is needed, review the vehicles
owners manual section on replacing the
tail light bulbs.) (Figure A)
3. Find the wiring that connects to the
reverse bulb. There is normally 2 wires.
(Figure B) Strip the insulation to expose
the copper wire.
4. Using a Digital Multi-meter on the DC
Voltage setting, to verify the reverse wire.
(Figure C)
5. Connect the wires from the camera
• Connect the RED wire to reverse,
either found at the taillight or
another source for reverse.
• Connect the BLACK wire to chassis
ground. Figure C
Figure B
Figure A
12 V - 12V
Select this symbol on the meter

386-257-1187
|
iBEAMUSA.com
4
Figure A Figure B
WIRELESS PAIRING
Mirror/Monitor to Camera pairing
1. Before operation, the camera and mirror
need to be paired to each other. Start by
connecting power to both devices. If camera
is connected to reverse, the vehicle must be
put into the reverse gear. NOTE: Please acti-
vate parking brake while pairing for safety.
2. Once both devices are paired, Press the
MENU button (middle button) on the mirror
and then choose the PAIRING selection.
Then press and hold the MENU button for 2
seconds to select PAIRING.
3. The monitor will count down 20 seconds to
achieve the pairing of camera to monitor.
Once the pairing has happened, the camera
image will appear. The camera and monitor
are now paired
4. Put the vehicle back into PARK, turn the vehi-
cle off, turn the vehicle back on and shift into
reverse to test the camera and monitor.

REV. 07/20/2020 INSTTE-WKMR43 5
Figure A Figure B
DISPLAY SETTINGS
Display Settings
Brightness
1. Press the MENU button (middle button) to
enter into the settings menu, use the + and -
buttons (+ = top button, - = bottom button) to
navigate to the PICTURE menu. Press and hold
the MENU button for 2 seconds to enter the
PICTURE menu.
2. Press the + and - buttons to navigate to the
setting you want to choose. Then press and
hold the MENU button for 2 seconds
3. Use the + and - buttons to increase or
decrease the set values.
4. Press the MENU button to exit the settings.
Reversing/flipping the image
1. Press the MENU button to enter into the
settings menu, use the + and - buttons
to navigate to the MIR-FLIP menu. Press
and hold the MENU button to enter the
MIR-FLIP menu.
2. Using the + and - buttons to switch
between NORMAL, MIRROR, FLIP or MIRROR
FLIP.
3. Press the MENU button to exit the settings.

386-257-1187
|
iBEAMUSA.com
6
1.5 FT 11 FT
4.5 FT
NOTE: To activate and de-activate parking lines, press the top and bottom button on the back on the monitor.
WIRE LENGTHS

REV. 07/20/2020 INSTTE-WKMR43 7
TV SYSTEM NTSC
EFFECTIVE PIXEL 976 X 592 pixels
IP RATING IP67
VISUAL ANGLE 120 horizantal 170 diagonal
MIN. ILLUMINATION 0.1 Lux
WORKING VOLTAGE 9 - 16V
WORKING TEMP. -30 C ~ 70 C
STORAGE TEMP. - 40 C ~ 120 C
SCREEN SIZE 4.3 inch LCD
DISPLAY RESOLUTION 480 X 272
ASPECT RATIO 16:9
POWER CONSUMPTION less than 3 w
SPECIFICATIONS

©COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
iBEAMUSA.comiBEAM Vehicle Safety Sytems ®REV. 07/20/2020 INSTTE-WKMR43
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
TE-WKMR43
INSTALLATION INSTRUCTIONS
#IBEAMSAFETY
Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at:
[e-mail]
Tech Support Hours (Eastern Standard Time)
Monday - Friday: 9:00 AM - 7:00 PM
Saturday: 10:00 AM - 7:00 PM
Sunday: 10:00 AM - 4:00 PM
Metra Recommends MECP
certified technicians