IBM System Storage EXN2000 Manual

EXN2000
Installation and Setup Instructions
IBM System Storage

Customer-supplied items needed for setup:
!
!
!
!
#2 Phillips screwdriver
ESD wrist strap
Pointed tool for setting ID switches
7mm nut driver
1
This document provides installation and setup instructions for the IBM System
Storage EXN2000 storage expansion unit. Additional information about the
EXN2000 can be found in the
.
This document presents the EXN2000 information previously found in the
,
GC26-7786.
IBM System Storage EXN2000 Storage Expansion
Unit Hardware and Service Guide
IBM System Storage EXN1000 and EXN2000 Installation and Setup Instructions
Note:
r
Need help?
If you encounter any difficulties while setting up your system, contact IBM service
and support for assistance. Information can also be found at the following Web
site:
www.ibm.com/storage/support/nas/
TM
Read the safety notices:
Before continuing, make sure that you have reviewed the safety notices in the
documentation that came with this system. Do not plug any cables into the
system, adapters, or any electrical outlets until you have reviewed the safety
information and followed the procedures in this document.

1Unpacking the EXN2000 (expansion unit)
EXN2000
(expansion unit)
Note: The contents of the box will differ based
on the model you purchased. See Step 1.1 for a
list of contents for specific models.
1
2
Important:
If your system was shipped already assembled and cabled in a rack, go
directly to the for the storage system to
boot the system.
Installation and Setup Instructions
Accessory kit:
- IBM rail kit
- Power cables
- Setup kit

1.1
1.2
1.3
Remove the expansion unit and its tray using the handles built into the
cardboard tray. Place the expansion unit and tray on a table.
Remove the top portion of the plastic surrounding the expansion unit.
32 kg (70.5 lb)
3
Verify that the shipping packages include the following items:
EXN2000 (2863-001)
1 EXN2000
1 Publications
2 Power cords
ables
May be present:
1 IBM rail kit
1Wriststrap,ESD
1 Enclosure shelf Ids label
Miscellaneous data c
Small Form Factor Pluggable (SFP) module
DANGER: Expansion units are extremely heavy. To avoid injuring yourself
or damaging an expansion unit, you must work with at least two other
people when you install an expansion unit in the rack. Do not remove the
disk drives to reduce the weight.
Caution: Use safe practices when lifting.

Installing the rails in an IBM 19-inch rack
2
4
Note: Read this document in its entirety before proceeding.
2.1 Loosen (but do not remove) the four rail adjustment screws on each rail.
2.2
Right rail
Left rail
Front of rack
Rear of rack
Rail adjustment
screws
Locating pins
Use the figure on the next page for reference. At the front of the rack,
position the right-hand rail into the rack at the appropriate EIA location
(make sure that the two locating pins seat properly). The bottom of the rail
should line up with the bottom EIA boundary.
When installed, each EXN2000 unit will occupy a 3U space.
Using two silver pan head M5 screws, attach the rail to the front of the rack
using holes H3 and H7. T
Note:
ighten these screws with a screwdriver.

5
2.3 At the rear of the rack, position the rail at the same EIA location used in
step 2.2 (make sure that the locating pins seat properly). Using two silver
pan head M5 screws,
Tighten these screws with a screwdriver.
attach the rail to the rack using holes H2 and H8.
2.4 Tighten the four rail adjustment screws on the installed rail.
2.5 Repeat steps 2.2 through 2.4 for the left-hand rail.
2.6 Repeat steps 2.1 through 2.5 if installing a second EXN2000.
Section of rack EIA rail
H2
H1
H3
H4
H5
H6
H7
H8
H9
Locating pins
Bottom rail screws
REAR
Left and Right
Rails
Chassis attach screws
H2
H1
H3
H4
H5
H6
H7
H8
H9
FRONT
Left and Right
Rails
Top rail screws
Locating pins
Chassis attach screws 1 EIA unit (1U)
Bottom rail screws
Top rail screws

3.1 From the front of the rack, place the expansion unit onto the rails and
slide it in until the front mounting bracket of the expansion unit is flush
with the frame rails of the rack.
3Installing the expansion unit into the rack
3.2
32 kg (70.5 lb)
6
Caution: Use safe practices when lifting.
DANGER: Expansion units are extremely heavy. To avoid injuring yourself
or damaging an expansion unit, you must work with at least two other
people when you install an expansion unit in the rack. Do not remove the
disk drives to reduce the weight.
Note: Verify the shelf IDs before installing into the rack. All shelf IDs should
be correct and sequential in the individual loop(s). If the filer and expansion
unit were configured together by manufacturing, these IDs are already set.
The label on the front should match the switch on the back. For more
information, refer to the .EXN2000 Hardware and Service Guide
At the front of the rack, using four black hex head M5 screws in the H2
and H8 holes, secure the system unit to the rack by threading the screws
through the system unit bracket and the rack frame rail into the threaded
rail nuts. Tighten the screws using the 7mm nut driver.
3.3 From the rear of the rack, use two silver pan head M5 screws to attach
the rear of the chassis to the rails as shown below.
Screws

7
4.1 Make sure that all expansion unit speed switches are set to the correct
position for your application.
For example, if connecting to an N3700 storage system, the speed switch
must be set to the 1Gb position. If connecting to an N5000 series or an
N7000 series storage system, the speed switch must be set to the 2Gb
position.
Use the following diagram for reference:
Setting the speed switch
4
2
1Gb 2Gb
Shelf ID
Gb switch
(set to 1 Gb)
Mute button
Out port
In port activity LED
In port
Out port activity LED
Fault LED
Speed (2 Gb) LED
2
Shelf ID - close-up view

5Grounding expansion units
5.1 If only one expansion unit is being used, go to Step 6, "Installing the
power cables" on page 9.
If two or more expansion units are being used continue with the
following.
Using the grounding kit, fasten the lug, fasten the lug at one end of the
0.25m grounding cable to one of the two threaded inserts (adjacent to
the power supply receptacles as indicated by a ground symbol) at the
back of the expansion unit using the M5 x 0.5-inch screw.
If additional expansion units need to be grounded, continue attaching
the grounding cables from unit to unit, overlaying the hole on one end
of the grounding cable from one to the next.
Note: For proper grounding, you must fasten your expansion unit(s)
together. Use the provided braided copper grounding cables and screws
(may be in the rail kit).
Dual expansion unit grounding Multiple expansion unit grounding
Grounding
cable
Grounding
cables
8