IBM Flex System FC3171 User manual

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 1
I B M ®
IBM Flex System FC3171 8Gb SAN Switch and
Pass-thru
IBM Redbooks Product Guide
The IBM Flex System™ FC3171 8Gb SAN Switch is a full-fabric Fibre Channel component with expanded
functionality. The SAN switch supports high speed traffic processing for IBM Flex System configurations,
and offers scalability in external SAN size and complexity, and enhanced systems management
capabilities. The IBM Flex System FC3171 8Gb Pass-thru supports a fully interoperable solution for
seamless integration of the Fibre Channel initiators to an existing fabric. The pass-thru module uses
industry-standard N_Port ID virtualization (NPIV) technology to provide a cost-effective connectivity
solution for the IBM Flex System chassis.
Figure 1 shows the switch module.
Figure 1. IBM Flex System FC3171 8Gb SAN Switch
Did you know?
These switch modules are licensed to operate in either full-fabric mode or intelligent pass-thru
mode.These modules allow IBM Flex System integration with any open-standards-based SAN, whether
the module has enterprise open-system fabric functionality using the full-fabric mode, or the module has
transparent switching functionality using the intelligent pass-thru mode.
IBM Flex System, a new category of computing and the next generation of Smarter Computing, offers
intelligent workload deployment and management for maximum business agility. This chassis delivers
high-speed performance complete with integrated servers, storage, and networking for multi-chassis
management in datacenter compute environments. Furthermore, its flexible design can meet the needs of
varying workloads with independently scalable IT resource pools for higher utilization and lower cost per
workload. While increased security and resiliency protect vital information and promote maximum uptime,
the integrated, easy-to-use management system reduces setup time and complexity, providing a quicker
path to ROI.

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 2
Part number information
The part numbers to order the switch and optional upgrades are shown in Table 1.
Table 1. Part numbers and feature codes for ordering
Description Part number Feature codes
IBM Flex System FC3171 8Gb SAN Switch 69Y1930 A0TD / 3595*
IBM Flex System FC3171 8Gb SAN Pass-thru 69Y1934 A0TJ / 3591
* The first feature code listed is for configurations ordered through IBM System x® sales channels. The second
feature code is for configurations ordered through the IBM Power Systems™sales channel.
Unlike FC3171 8Gb SAN Switch full-fabric operations, the pass-thru module concentrates multiple
compute nodes into the external ports. The external ports connect to external Fibre Channel switches that
support NPIV. The internal ports connect directly to compute nodes through the chassis backplanes. The
pass-thru module presents one or more compute nodes per port to the fabric. The pass-thru module
expands the fabric, but, unlike a full-fabric switch, it does not count against the fabric domain.
The part number includes the following items:
One IBM Flex System FC3171 8Gb SAN Switch or Pass-thru

Important Notices Flyer

Warranty Flyer

Documentation CD-ROM

The switch does not include a serial management cable; however, the IBM Flex System Management
Serial Access Cable, 90Y9338, is supported and contains two cables, a mini-USB-to-RJ45 serial cable
and a mini-USB-to-DB9 serial cable, either of which can be used to connect to the switch locally for
configuration tasks and firmware updates.
The switch comes without any SFP+ transceivers, they must be ordered separately to provide outside
connectivity. The following table lists supported SFP+ options.
Table 2. Supported SFP+ transceivers
Part number Feature code* Description
44X1964 5075 / 3286 IBM 8Gb SFP+ SW Optical Transceiver
39R6475 4804 / 3238 IBM 4Gb SW SFP Transceiver
* The first feature code listed is for configurations ordered through System x sales channels. The second feature
code is for configurations ordered through the IBM Power Systems sales channel.

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 3
Benefits
The switch offers the following key benefits:
Easy to install and manage

On-board GUI — no software to load. Just point a web browser at any switch and manage the entire
fabric from that location. No matter what your level of expertise, the web-based QuickTools interface
has all you need for basic fabric management.
Fast, reliable performance

The switch provides uncontested “wire speed” bandwidth at every port — a total of 320 Gbps per
switch with less than 4 ms fabric latency.
Interoperability

The switch supports FC-SW-2 interoperability standards and transparent mode of operations to
simplify integration into a multi-vendor fabric.
Investment protection

The switch provides low total cost of ownership (TCO) with quick set up and easy to manage
integrated tools.
Features and specifications
The FC3171 8Gb SAN Switch and Pass-thru have the following features and specifications:
Internal ports:

14 internal full-duplex 8 Gb FC ports

Internal ports operate as F_ports (fabric ports) on the FC3171 8Gb SAN Switch

Internal ports operate as TH_Ports (transparent host ports) on the FC3171 8Gb SAN Pass-thru

Two internal full-duplex 1 GbE ports connected to the chassis management module

External ports:

Six external ports for 8 Gb SFP+ or 4 Gb SFP transceivers supporting 2 Gb, 4 Gb, and 8 Gb port

speeds (SFP+ modules are not included and must be purchased separately - see Table 2)
External ports can operate as F_ports (fabric ports), FL_ports (fabric loop ports), or E_ports

(expansion ports) on the FC3171 8Gb SAN Switch
External ports operate as TF_Ports (Transparent Fabric Ports) on the FC3171 8Gb SAN

Pass-thru
One external 100 Mb Fast Ethernet (100BASE-TX) port with RJ-45 connector for switch

configuration and management
One RS-232 serial port (mini-USB connector) that provides an additional means to configure the

switch module
Transparent (N_Port ID Virtualization - NPIV) mode support

Power-on self-test diagnostics and status reporting

Support for Non-Disruptive Code Load Activation (NDCLA)


IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 4
Registered State Change Notification (RSCN):

The switch supports RSCN as described in FC-FLA. RSCN enables an agent to register for change
events in the fabric and attached devices.
Support for standards-based FC-SW2 interoperability

Error detection:

Cyclic redundancy check (CRC)

8-byte and 10-byte conversion

Parity

Long frame and short frame

D_ID mismatch

S_ID mismatch

Frame bundling:

No frame bundling (frames are intermixed from different source ports)

Soft lockdown (the I/O module waits for the sequence to be completed or a gap in the frame

traffic to occur before it services requests from a different port)
Configurable Fabric Address Notification (FAN)

Supports up to 239 switches depending on configuration

8 Gb switch fabric aggregate bandwidth: 320 Gbps at full duplex

Maximum frame size: 2148 bytes (2112 byte payload)

Nonblocking architecture to prevent latency

Fabric Latency: Less than 4 ms

Support for Call Home function

Support for Domain Name Service (DNS)

Support for Internet protocol (IP) Version 4 and Version 6

Support for Internet protocol security (IPsec)

Support for separate trap community strings for each trap address

Support for Simple Network Management Protocol (SNMP) Version 3

Support for vital product data (VPD)

Easier SAN maintenance, isolation and troubleshooting with SANdoctor that is a part of base

firmware
Optional small form-factor pluggable plus (SFP+) modules

The following software features come with the switch module:
QuickTools Web interface

Fabric Security


IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 5
The switch supports the following management methods:
Web interface through QuickTools

Command-line interface through SSH (Telnet is also supported but disabled by default)

Switch simple network management protocol (SNMP) agent: enables a network management

workstation to receive configuration values, traffic information, and Fibre Channel failure data through
SNMP and the Ethernet interface
Supported Fibre Channel standards
The switch supports the following Fibre Channel standards:
C-PH version 4.3

FC-PH-2

FC-PH-3

FC-AL version 4.5

FC-AL-2 Rev 7.0

FC-FLA

FC-GS-3

FC-FG

FC-PLDA

FC-Tape

FC-VI

FC-SW-2

Fibre Channel Element MIB RFC 2837

Fibre Alliance MIB version 4.0

Supported chassis and adapter cards
The switches are installed in switch bays in the rear of the IBM Flex System Enterprise Chassis as shown
in the following figure. Switches are normally installed in pairs because I/O adapter cards installed in the
compute nodes route to two switch bays for redundancy and performance.
Figure 2. Location of the I/O bays in the IBM Flex System Enterprise Chassis

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 6
The connections between the adapters installed in the compute nodes to the switch bays in the chassis
are shown diagrammatically in the following figure. The figure shows both half-wide servers, such as the
x240 with two adapters, and full-wide servers, such as the p460 with four adapters.
Figure 3. Logical layout of the interconnects between I/O adapters and I/O modules
The IBM Flex System FC3171 8Gb SAN Switch and Pass-thru can be installed in bays 1, 2, 3, and 4 of
the Enterprise chassis. Supported adapter card must be installed in a corresponding slot of the compute
node (slot A1 when switches are installed in bays 1 and 2 or slot A2 when switches are in bays 3 and 4).
With compute nodes that have an integrated dual-port 10 GbE network interface controller (NIC) these
switches can only be installed in bays 3 and 4 because integrated NICs ports are routed to bays 1 and 2
with a specialized periscope connector and the FC adapter card cannot be installed in slot A1. However,
when needed, the periscope connector can be replaced with an FC adapter card, in which case integrated
NIC will be disabled and FC switches can be used in bays 1 and 2.

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 7
The following table shows the connections between adapters installed in the compute nodes to the switch
bays in the chassis with IBM Flex System FC3171 8Gb SAN switches or Pass-thru modules and
supported dual-port FC adapters.
Table 4. Adapter to I/O bay correspondence
I/O adapter slot
in the server Port on the adapter Corresponding I/O module bay in the chassis
Port 1 Module bay 1Slot 1
Port 2 Module bay 2
Port 1 Module bay 3Slot 2
Port 2 Module bay 4
Port 1 Module bay 1
Slot 3
(full-wide compute nodes only) Port 2 Module bay 2
Port 1 Module bay 3
Slot 4
(full-wide compute nodes only) Port 2 Module bay 4
The following table lists the storage I/O adapters supported by the FC3171 8Gb SAN Switch and SAN
Pass-thru and those that are not supported.
Table 5. Storage adapters
Description
Part
number Feature code (x-config /
e-config)
Support for
FC3171
switch and
pass-thru
16 Gb Fibre Channel
IBM Flex System FC5022 2-port 16Gb FC Adapter 88Y6370 A1BP / None No
IBM Flex System FC5024D 4-port 16Gb FC Adapter 95Y2379 A3HU / A3HU No
IBM Flex System FC5052 2-port 16Gb FC Adapter 95Y2386 EC23 / A45R No
IBM Flex System FC5054 4-port 16Gb FC Adapter 95Y2391 EC2E / A45S No
IBM Flex System FC5172 2-port 16Gb FC Adapter 69Y1942 A1BQ / A1BQ Yes
8 Gb Fibre Channel
IBM Flex System FC3172 2-port 8Gb FC Adapter 69Y1938 A1BM / 1764 Yes
IBM Flex System FC3052 2-port 8Gb FC Adapter 95Y2375 A2N5 / None Yes

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 8
The adapters are installed in slots in each compute node. The following figure shows the locations of the
slots in the x240 Compute Node. The positions of the adapters in the other supported servers are similar.
Figure 4. Location of the I/O adapter slots in the IBM Flex System x240 Compute Node
Connectors and LEDs
Figure 5 shows the front panel of the IBM Flex System FC3171 8Gb SAN Switch and Pass-thru.
Figure 5. Front panel of the IBM Flex System FC3171 8Gb SAN Switch and Pass-thru
The front panel contains the following components:
LEDs that display the status of the switch module and the fabric:

OK LED indicates that the switch module has passed the power-on self-test (POST) with no

critical faults and is operational.
Identify: This Blue LED can be used to identify the switch physically, by illuminating via the

management software.
Error LED (switch module error) indicates that the switch module has failed the POST or detected

an operational fault.
One mini-USB RS-232 console port that provides an additional means to configure the switch

module. This mini-USB-style connector enables connection of a special serial cable. (The cable is
optional and it is not included with the switch; see the Part number information section for details).

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 9
One 100 Mb Fast Ethernet RJ-45 port for switch configuration and management

Six external SFP+ port connectors to attach SFP+ modules for 8 Gb or 4 Gb connections to external

Fibre Channel devices
An FC link error LED, an FC Tx/Rx LED, and FC Loggen-in LED for each external port on the switch

Cabling requirements
The cables required for the switch are as follows:
8 Gb FC SW SFP+ transceivers (see Table 2)

850 nm communication using multimode fiber cable (50 µ or 62.5 µ) up to 150 m at 8 Gbps, LC

duplex connector
4 Gb FC SW SFP transceivers (see Table 2)
850 nm communication using multimode fiber cable (50 µ or 62.5 µ) up to 300 m at 4 Gbps speed,

LC duplex connector
100BASE-TX (external 100 Mb Fast Ethernet management port)
UTP Category 5 (100 meters maximum)

EIA/TIA-568B 100-ohm STP (100 meters maximum)

RS-232 serial cable: Console cable DB-9-to-mini-USB or RJ-45-to-mini-USB (nonstandard use of

USB connector) that come with optional IBM Flex System Management Serial Access Cable,
90Y9338
Warranty
There is a 1-year, customer-replaceable unit (CRU) limited warranty. When installed in a chassis, these
switches assume your system’s base warranty and any IBM ServicePac® upgrade.
Physical specifications
The approximate dimensions and weight of the switch are as follows:
Height: 30 mm (1.2 in.)

Width: 401 mm (15.8 in.)

Depth: 317 mm (12.5 in.)

Weight: 3.0 kg (6.6 lb)

Shipping dimensions and weight (approximate):
Height: 114 mm (4.5 in.)

Width: 508 mm (20.0 in.)

Depth: 432 mm (17.0 in.)

Weight: 3.4 kg (7.6 lb)


IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 10
Operating environment
Temperature and altitude

Operating: 10°C to 52°C (50°F to 125.6°F) at an altitude of 0 to 914 m (0 to 3000 ft)

Operating: 10°C to 49° C (50°F to 120.2°F) at an altitude of 0 to 3000 m (0 to 10 000 ft)

Non-operating: -40°C to 65°C (-40°F to 149°F) at an altitude of 0 to 12 000 m (0 to 39 370 ft)

Humidity

Operating: 8% to 80%, noncondensing

Non-operating: 5% to 80%, noncondensing

Regulatory compliance
The switch conforms to the following standards:
FCC Title 47 CFR Part 15 Subpart B Class A (USA)

VCCI Class A ITE, April 2003 (Japan)

ICES-003 issue 3 (Canada)

A4EN55022 level A (EC)

Voltage fluctuations: EN 61000-3-3

Harmonics: EN 61000-3-2

Immunity: EN55024: 1998

C-Tick - AS/NZS CISPR 22 (Australia/New Zealand)

CE Mark - EN55022:1998 + A2:2003 and EN55024:1998 + A1:2001 + A2:2003

MIC Notice No. 2001-115 and No. 2001-116 (Korea)

GOST 29216-91 (Russia)

CISPR 22 Class A

BSMI CNS 13438 (Taiwan)

Communique No. 2004/9 and No. 2004/22 (Turkey)

EMC.CVG, 28 October 2002 (Saudi Arabia)

GB 9524:1998 (China)


IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 11
Popular configurations
The following figure shows use of the IBM Flex System FC3171 8Gb SAN Switch to route two ports on
the adapter card installed in slot 2 of the compute node. Each compute node has two 8 Gb FC ports, and
two FC3171 switches are installed in bays 3 and 4 of the Enterprise Chassis. The connections between
the adapter card and the switches are internal to the chassis. No cabling is needed.
Figure 5. Using FC3171 8Gb SAN Switches with FC3172 8Gb FC adapters installed in compute nodes
Table 6. Components used when connecting the 8 Gb FC adapters to the 8 Gb FC switches
Part number/machine type Description Quantity
8737-x2x IBM Flex System x240 Compute Node with
Embedded 10Gb Virtual Fabric Adapter 1 to 14
69Y1938 IBM Flex System FC3172 2-port 8Gb FC Adapter 1 per server
8721-A1x IBM Flex System Enterprise Chassis 1
49Y4294 IBM Flex System Fabric EN4093 10Gb Scalable
Switch 2
69Y1930 IBM Flex System FC3171 8Gb SAN Switch 2
Refer to the IBM System Storage® Interoperation Center (SSIC) for a list of supported Fibre Channel
configurations:
http://ibm.com/systems/support/storage/ssic

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 12
Related publications
For more information see the following IBM Flex System FC3171 8Gb SAN Switch and Pass-thru product
publications, available from the IBM Flex System Information Center:
http://publib.boulder.ibm.com/infocenter/flexsys/information/index.
jsp
SAN Switch and SAN Pass-thru User's Guide

Quick Tools User's Guide

Command Line Interface User's Guide

CIM Agent Reference Guide

Event Message Reference Guide

Simple Network Management Protocol Reference Guide

Other documents:
US Announcement Letter 112-053

http://ibm.com/common/ssi/cgi-bin/ssialias?infotype=dd&subtype=ca&&htmlfid=897/ENUS112-053
IBM Flex System Enterprise Chassis Product Guide

http://www.redbooks.ibm.com/abstracts/tips0865.html
IBM Redbooks® publication IBM Flex System Products and Technology , SG24-7984

http://www.redbooks.ibm.com/abstracts/sg247523.html
IBM Redbooks Product Guides for IBM Flex System servers and options

http://www.redbooks.ibm.com/portals/puresystems
IBM Flex System Interoperability Guide

http://ibm.com/support
Configuration and Option Guide

http://www.ibm.com/systems/xbc/cog/

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 13
Notices
This information was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in other countries. Consult your
local IBM representative for information on the products and services currently available in your area. Any reference
to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or
service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM
intellectual property right may be used instead. However, it is the user's responsibility to evaluate and verify the
operation of any non-IBM product, program, or service. IBM may have patents or pending patent applications
covering subject matter described in this document. The furnishing of this document does not give you any license
to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing, IBM Corporation, North Castle Drive, Armonk, NY 10504-1785 U.S.A.
The following paragraph does not apply to the United Kingdom or any other country where such provisions
are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies
or typographical errors. Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s)
and/or the program(s) described in this publication at any time without notice.
Any references in this information to non-IBM Web sites are provided for convenience only and do not in any
manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials
for this IBM product and use of those Web sites is at your own risk.IBM may use or distribute any of the information
you supply in any way it believes appropriate without incurring any obligation to you. Information concerning
non-IBM products was obtained from the suppliers of those products, their published announcements or other
publicly available sources. IBM has not tested those products and cannot confirm the accuracy of performance,
compatibility or any other claims related to non-IBM products. Questions on the capabilities of non-IBM products
should be addressed to the suppliers of those products. This information contains examples of data and reports
used in daily business operations. To illustrate them as completely as possible, the examples include the names of
individuals, companies, brands, and products. All of these names are fictitious and any similarity to the names and
addresses used by an actual business enterprise is entirely coincidental.
Any performance data contained herein was determined in a controlled environment. Therefore, the results
obtained in other operating environments may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements will be the same on generally
available systems. Furthermore, some measurement may have been estimated through extrapolation. Actual
results may vary. Users of this document should verify the applicable data for their specific environment.
COPYRIGHT LICENSE:
This information contains sample application programs in source language, which illustrate programming
techniques on various operating platforms. You may copy, modify, and distribute these sample programs in any
form without payment to IBM, for the purposes of developing, using, marketing or distributing application programs
conforming to the application programming interface for the operating platform for which the sample programs are
written. These examples have not been thoroughly tested under all conditions. IBM, therefore, cannot guarantee or
imply reliability, serviceability, or function of these programs.
© Copyright International Business Machines Corporation 2012. All rights reserved.
Note to U.S. Government Users Restricted Rights -- Use, duplication or disclosure restricted by
GSA ADP Schedule Contract with IBM Corp.

IBM Flex System FC3171 8Gb SAN Switch and Pass-thru 14
This document was created or updated on August 1, 2013.
Send us your comments in one of the following ways:
Use the online Contact us review form found at:

ibm.com/redbooks
Send your comments in an e-mail to:

redbo[email protected]
Mail your comments to:

IBM Corporation, International Technical Support Organization
Dept. HYTD Mail Station P099
2455 South Road
Poughkeepsie, NY 12601-5400 U.S.A.
This document is available online at http://www.ibm.com/redbooks/abstracts/tips0866.html .
Trademarks
IBM, the IBM logo, and ibm.com are trademarks or registered trademarks of International Business
Machines Corporation in the United States, other countries, or both. These and other IBM trademarked
terms are marked on their first occurrence in this information with the appropriate symbol (® or ™),
indicating US registered or common law trademarks owned by IBM at the time this information was
published. Such trademarks may also be registered or common law trademarks in other countries. A
current list of IBM trademarks is available on the Web at http://www.ibm.com/legal/copytrade.shtml
The following terms are trademarks of the International Business Machines Corporation in the United
States, other countries, or both:
IBM®
IBM Flex System™
Power Systems™
Redbooks®
Redbooks (logo)®
ServicePac®
System Storage®
System x®
Other company, product, or service names may be trademarks or service marks of others.