Icom CS-207 User manual

0
ICOM CS-207
OPERATING GUIDE (for IC-207H)
GETTING STARTED
I
p
Before using the program, make a backup copy of To use this program, the following hardware and
the original disk. Operate the program using the
# ba software are required:
A
ckup and keep the original in a safe p/ace. l IBM PC/AT or
PS/2 compatible computer with an
RS-232C serial port
This cloning program is designed to perform data
setting and cloning for the dual band transceiver
IC-207H.
l MS-DOS, PC-DOS or IBM DOS ver. 5.02 or higher
. OPC-646 CLONING CABLE
I
CONNECTIONS
I
cloning operations are performed from
computer’s keyboard including power ON -
only connect to a DC power supply is needed
r the transceiver.
DB9 female plug
IC-207H
(incl. level converter circuit)
\
Personal
computer
-646 Cloning cable
be purchased separately)
INSTALLATION AND PROGRAM START UP
n Installation and initial setup’
Connect the transceiver and PC as above then con-
nect a DC power supply to the the transceiver.
To install the CS-207 cloning software to
ICOM\CS207 directory of drive C while the program
disk is in drive A, type as follows at the DOS prompt:
A:\INSTALL A: C:\ICOM\CS207 [Enter]
T
I
Program drive
‘7”
Target drive/directory
A target directory is created if it does not already
exist; CS-207 cannot be installed to the root directory.
After the installation is finished, the CS-207 initial
setup screen appears and the transceiver model is
checked. Proceed as follows:
0 Select the connected RS-232C (COMlKOM2)
port with the [ t]/[ $1 and [Enter] keys.
@ Input your call sign then push [Enter].
@ After the initial setup, CS-207 is automatically
launched. Set or modify the data as desired.
l See the back page for operation.
@>‘fie the File sub menu to save the data or to exit
the program.
To start the program after installation, operate as
n Starting the program
follows at the DOS prompt:
@) Change to the installed directory.
l C:\ICOM\CS207 in case of the example at left.
@ Type as follows to start:
CS207 [Enter] (at the installed directory)
n Operating from a floppy disk
This program can be operated from a floppy disk.
0 Insert the backup disk into the floppy disk drive.
@ Select the floppy disk drive as the current drive.
@ Select the “CS207” directory.
@ Type “CS207,” then push [Enter] to start.
1 floppy disk.
NEVER remove the program disk from the floppy disk
drive while the
7
program is running.
NEVER set the floppy disk as write-protected.
Cloning will take 20 sec. or more when operating from a
Portions of this software are copyrighted by Microsoft Corporation.
MS-DOS is a Microsoft trademark.
I”,, m-,.-F m-.- -- --- ,.-..---
.~

MENU FLOW
Push [Alt] or [Esc] to select the TOP menu.
l The TOP menu lightens,
l ;
screens and operations can be selected from the TOP menu.
Push [Fl] to call up the help message.
To select a SUB menu, push
the highlighted key; or select
with the [d]/[c] keys then
push [Enter] or [ 4 1.
The screen darkens when the TOP
menu is selected.
File Screen Clone Print
Setup
Load
Memory CH
Read (- TR Current Display Type
Save
VFO
Write -) TR All Wallpaper
Delete DTMF Autodial
Information RS-232C
D OS Common
Call Sign
Preset
Exit
,
SUB MENU
DESCRIPTION
SUB MENU DESCRIPTION
Load Loads data from a saved file. Read
(- TR Reads clone data from a connected
Save Saves data to a desired file. File transceiver.
extension (.ICF) is added automatically.
2
Sends clone data to a connected
Delete
Deletes a file.
2 Write -) TR
0
transceiver.
g DOS Allows you to use a DOS command. To Shows the connected transceiver model
return to the previous screen, type Information and clone comment.
“EXIT” then push [Enter].
Loads a preset file. Moves the cursor Current Prints out currently displayed screen
Preset
to the first memory channel for input in
-g
data.
the V or U memory channel screen.
p AII
Prints out all set data.
Exit
Quits and exits the program, then
returns to the DOS prompt. Selects the display type from color
l/2
Sets the operating frequency, duplex
Display Type and monochrome. Customized colors
Memory CH setting, etc. for call, memory and scan can be used.
edge channels.
3 Wallpaper Selects the wallpaper. This can be
c VFO
Sets the operating frequency, duplex
z
previewed before selection,
z
setting, etc. for VFO.
$j DTMF Sets the DTMF codes, DTMF
RS- 232C Selects one of the computer’s
RS232C
ports for cloning connection.
Autodial
transmission speed, etc.
C
Sets commonly used data, such as set Call
Sian
Enters your call sign.
ommon mode settings, initial set mode settings,
cloning comments, etc.
- _
Ic.nm
Inr