3
2
PANEL DESCRIPTION
!1 VOLUME CONTROL [VOL] (p. 00)
Adjusts the audio output level.
•Audio does not come from the speaker when:
- A microphone is not connected.
- The speaker switch is turned ON.
- The squelch switch is turned ON and no signal is being
received.
!2 FUNCTION SWITCH [F] (p. 00)
After pushing, activates the secondary functions.
•“F”appears when when a secondary function can be
accessed.
!3 KEYPAD (p. 00)
➥Input numeral “1”for channel number,
frequency input, etc.
➥Input “1,”“Q”or “Z”for channel comment
input.
➥After pushing [F], turns the noise
blanker function ON and OFF. (p. 00)
➥Input numeral “2”for channel number,
frequency input, etc.
➥Input “2,”“A,”“B”or “C”for channel com-
ment input.
➥After pushing [F], turns the voice or S-
meter squelch ON and OFF. (p. 00)
➥Input numeral “3”for channel number,
frequency input, etc.
➥Input “3,”“D,”“E”or “F”for channel com-
ment input.
➥After pushing [F], starts and stops the
scan function. (p. 00)
➥Input numeral “4”for channel number,
frequency input, etc.
➥Input “4,”“G,”“H”or “I”for channel com-
ment input.
➥After pushing [F], turns the speaker out-
put ON and OFF. (p. 00)
➥Input numeral “5”for channel number,
frequency input, etc.
➥Input “5,”“J,”“K”or “L”for channel com-
ment input.
➥After pushing [F], turns the AGC function
ON and OFF. (p. 00)
➥Input numeral “6”for channel number,
frequency input, etc.
➥Input “6,”“M,”“N”or “O”for channel com-
ment input.
➥After pushing [F], enters to the RF gain
adjustment mode. (p. 00)
➥Input numeral “7”for channel number,
frequency input, etc.
➥Input “7,”“P, ”“R”or “S”for channel com-
ment input.
➥After pushing [F], selects low transmit
output power. (p. 00)
➥Input numeral “8”for channel number,
frequency input, etc.
➥Input “8,”“T,”“U”or “V”for channel com-
ment input.
➥After pushing [F], selects middle trans-
mit output power. (p. 00)
➥Input numeral “9”for channel number,
frequency input, etc.
➥Input “9,”“W,”“X”or “Y”for channel com-
ment input.
➥After pushing [F], selects high transmit
output power. (p. 00)
➥Input numeral “0”for channel number,
frequency input, etc.
➥Input “0”and symbols (as follows) for
channel comment input.
➥Fixes input of channel number, frequency
and channel comment, etc.
➥When pushed for 1 sec., stores pro-
grammed frequency, operating mode and
memory comment into a channel.
➥After pushing [F], clears clarity setting.
➥Selects display type:
When channel comment indication is ON;
switches transmit frequency indication
ON and OFF
when channel comment indication is OFF;
switches channel comment indication
ON and OFF
➥After pushing [F], enters channel com-
ment programming mode, when channel
comment indication is ON.
!4 SET SWITCH [SET]
➥Enters quick set mode (p. 00)
➥After pushing [DSC], enters DSC set mode.
(p. 00)
!5 TUNE/THROUGH SWITCH [TUNE
THRU
] (p. 00)
➥Starts tuning when an optional antenna tuner is
connected.
•“TUNE”appears when tuned.
•When the tuner cannot tune the antenna, the tuning
circuit is bypassed automatically after 20 sec.
➥After pushing [F], bypasses an external antenna
tuner.
•“THROUGH”appears instead of “TUNE”indication.
!6 MODE/DIMMER SWITCH [MODE
DIM
](p. 00)
➥Push to select an operating mode.
•J3E, H3E, LSB, J2B, F1B and A1A modes are avail-
able, depending on version or countries.
➥After pushing [F], selects LCD backlight bright-
ness.
!7 E-MAIL SWITCH [e-mail] (p. 00)
➥Selects the operating frequencies, mode and fil-
ter setting for e-mail operation.
