Icom IC-T70A User manual

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CEL-
LULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED
UNDER FCC RULES AND FEDERAL LAW.
INSTRUCTION MANUAL
New2001
iT70A
iT70
E
VHF/UHF DUAL BAND FM TRANSCEIVER

i
New2001 New2001
FOREWORD
Thank you for choosing this Icom product. This product is de-
signed and built with Icom’s state of the art technology and
craftsmanship. With proper care this product should provide
you with years of trouble-free operation.
EXPLICIT DEFINITIONS
WORD DEFINITION
RDANGER! Personal death, serious injury or an ex-
plosion may occur.
RWARNING! Personal injury, fire hazard or electric
shock may occur.
CAUTION Equipment damage may occur.
NOTE Recommended for optimum use. No risk
of personal injury, fire or electric shock.
Icom is not responsible for the destruction or damage to the
Icom transceiver, if the malfunction is because of:
• Force majeure, including, but not limited to, fires, earth-
quakes, storms, floods, lightnings, or other natural disas-
ters, disturbances, riots, war, or radioactive contamination.
• The use of Icom transceiver with any equipment that is not
manufactured or approved by Icom.
FEATURES
❍Dust-protection/Splash-resistant construc-
tion (IP54*)
*Only when the battery pack/case, antenna and jack cover
are attached.
❍Built in VOX circuit enabling the VOX opera-
tion* (voice operated transmission)
*To use the VOX operation, an optional headset and a
plug adapter cable are additionally required.
❍700 mW* AF power with BTL (bridge-tied load)
amplier
*At 10% distortion with a 16 Ωload (internal speaker)
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This
instruction manual contains important operating instructions
for the IC-T70A/IC-T70E.

New2001
ii
RDANGER! NEVER short terminals (or charging terminals)
of the battery pack. Also, current may flow into nearby metal objects
such as a key, so be careful when placing the battery packs (or the
transceiver) in handbags, and so on. Simply carrying with or placing
near metal objects such as a key, and so on may cause shorting. This
may damage not only the battery pack, but also the transceiver.
RDANGER! NEVER use and charge only specified Icom bat-
tery packs with Icom transceivers or Icom chargers. Only Icom bat-
tery packs are tested and approved for use with Icom transceivers or
charged with Icom chargers. Using third party or counterfeit battery
packs or chargers may cause smoke, fire, or cause the battery to burst.
RWARNING RF EXPOSURE! This device emits Radio
Frequency (RF) energy. Caution should be observed when operating
this device. If you have any questions regarding RF exposure and
safety standards please refer to the Federal Communications Com-
mission Office of Engineering and Technology’s report on Evaluating
Compliance with FCC Guidelines for Human Radio Frequency Elec-
tromagnetic Fields (OET Bulletin 65)
RWARNING! NEVER hold the transceiver so that the an-
tenna is very close to, or touching exposed parts of the body, espe-
cially the face or eyes, while transmitting. The transceiver will perform
best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips
and the transceiver is vertical.
RWARNING! NEVER operate the transceiver with a head-
set or other audio accessories at high volume levels. The continuous
high volume operation may cause a ringing in your ears. If you expe-
rience the ringing, reduce the volume level or discontinue use.
RWARNING! NEVER operate the transceiver while driving
a vehicle. Safe driving requires your full attention—anything less may
result in an accident.
RWARNING! NEVER connect the transceiver to a power
source of more than 16 V DC such as a 24 V DC. This could cause a
fire or damage the transceiver.
RWARNING! NEVER reverse the DC power cable polarity
when connecting to a power source. This could damage the transceiver.
RWARNING! NEVER operate or touch the transceiver with
wet hands. This may result in an electric shock or may damage the
transceiver.
CAUTION: MAKE SURE the flexible antenna, battery pack,
and jack cover are securely attached to the transceiver, and that the
antenna and battery pack are dry before attachment. Exposing the
inside of the transceiver to dust or water will result in serious damage
to the transceiver.
DO NOT use harsh solvents such as benzine or alcohol to clean
the transceiver, because they can damage the transceiver’s surfaces.
DO NOT operate the transceiver near unshielded electrical blast-
ing caps or in an explosive atmosphere.
DO NOT modify the transceiver. The specifications may change
and then not comply with the requirements of a corresponded regula-
tion. The transceiver warranty does not cover any problems caused
by unauthorized modification.
DO NOT push [PTT] when you do not actually intend to transmit.
PRECAUTIONS

iii
New2001
FCC INFORMATION
• FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and re-
ceiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
PRECAUTIONS
DO NOT operate or place the transceiver in direct sunlight
or in areas with temperatures below –20°C (–4˚F) or above
+60°C (+140˚F).
BE CAREFUL! The transceiver will become hot when operat-
ing it continuously for long periods of time.
KEEP the transceiver away from heavy rain, and never immerse
it in the water. The transceiver meets IP54* requirements for dust-
protection and splash resistance. However, once the transceiver has
been dropped, dust-protection and splash resistance cannot be guar-
anteed because of possible damage to the transceiver’s case or the
waterproof seal.
*Only when the supplied battery pack (or optional battery pack/
case), antenna and jack cover are attached.
Even when the transceiver power is OFF, a slight current still flows
in the circuits. Remove the battery pack or batteries from the trans-
ceiver when not using it for a long time. Otherwise, the installed bat-
tery pack or batteries will become exhausted, and will need to be
recharged or replaced.
MAKE SURE to turn OFF the transceiver power before con-
necting or disconnecting the supplied or optional accessory.
CAUTION: Changes or modifications to this device, not
expressly approved by Icom Inc., could void your authority
to operate this device under FCC regulations.
New2001
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom
Incorporated (Japan) in Japan, the United States, the United King-
dom, Germany, France, Spain, Russia, Australia, New Zealand, and/
or other countries. and/or other countries.
Microsoft, Windows and Windows Vista are registered trademarks of
Microsoft Corporation in the United States and/or other countries.

New2001
iv
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
The following accessories are supplied with the transceiver.
qHand strap ��������������������������������������������������������������������� 1
wAntenna �������������������������������������������������������������������������� 1
eBattery pack* ������������������������������������������������������������������ 1
or
Battery case* ������������������������������������������������������������������ 1
rBelt clip* ��������������������������������������������������������������������������1
tBattery charger* ������������������������������������������������������������� 1
or
Battery charger* and power adapter* ����������������������� 1 set
* Not supplied, or the shape is different, depending on the transceiver
version.
SUPPLIED ACCESSORIES
t
eq
r
w
or
DISPOSAL
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you
that in the European Union, all electrical and
electronic products, batteries, and accumula-
tors (rechargeable batteries) must be taken
to designated collection locations at the end
of their working life. Do not dispose of these
products as unsorted municipal waste.
Dispose of them according to the laws in your area.

v
New2001 New2001
FOREWORD ������������������������������������������������������������������������������������� i
EXPLICIT DEFINITIONS������������������������������������������������������������������� i
FEATURES���������������������������������������������������������������������������������������� i
IMPORTANT�������������������������������������������������������������������������������������� i
PRECAUTIONS����������������������������������������������������������������������������ii–iii
FCC INFORMATION ����������������������������������������������������������������������� iii
SUPPLIED ACCESSORIES������������������������������������������������������������ iv
DISPOSAL��������������������������������������������������������������������������������������� iv
TABLE OF CONTENTS �������������������������������������������������������������� v–vi
1 ACCESSORY ATTACHMENT·················································1–2
■Hand strap �������������������������������������������������������������������������������1
■Belt clip ������������������������������������������������������������������������������������1
■Battery pack�����������������������������������������������������������������������������2
■Antenna �����������������������������������������������������������������������������������2
2 PANEL DESCRIPTION ···························································3–8
■Front, top and side panels �������������������������������������������������������3
■Function display�����������������������������������������������������������������������6
3 BATTERY CHARGING ·························································8–15
■Caution (for the supplied BP-264 Ni-MH battery pack)������������8
■Caution (for the optional BP-265 Li-Ion battery pack)��������������9
■Battery case (BP-263) �����������������������������������������������������������11
■Battery information ����������������������������������������������������������������11
■Regular charging �������������������������������������������������������������������12
■Desktop battery chargers ������������������������������������������������������13
■External DC power operation�������������������������������������������������15
4 BASIC OPERATION ···························································16–23
■Power ON ������������������������������������������������������������������������������ 16
■Setting audio volume �������������������������������������������������������������16
■Setting the squelch level��������������������������������������������������������17
■Monitor function ���������������������������������������������������������������������17
■Selecting the mode����������������������������������������������������������������18
■Setting the tuning step�����������������������������������������������������������19
■Setting the frequency�������������������������������������������������������������19
■Operating mode selection������������������������������������������������������21
■Key lock function��������������������������������������������������������������������21
■Receiving�������������������������������������������������������������������������������22
■Transmit power selection �������������������������������������������������������22
■Transmitting����������������������������������������������������������������������������23
5 REPEATER AND DUPLEX OPERATIONS ························24–28
■Repeater operation����������������������������������������������������������������24
■Duplex operation��������������������������������������������������������������������26
■Reverse duplex function ��������������������������������������������������������26
■Auto repeater function �����������������������������������������������������������27
■1750 Hz tone �������������������������������������������������������������������������28
6 MEMORY/CALL CHANNELS·············································29–39
■General description����������������������������������������������������������������29
■Selecting a call channel���������������������������������������������������������29
■Selecting a memory channel �������������������������������������������������30
■Memory channel programming����������������������������������������������31
■Memory bank setting �������������������������������������������������������������32
■Memory bank selection����������������������������������������������������������33
■Programming memory/bank/scan name��������������������������������34
TABLE OF CONTENTS

New2001
vi
■Selecting memory/bank name indication�������������������������������35
■Display type ���������������������������������������������������������������������������36
■Copying memory/call contents�����������������������������������������������37
■Memory clearing ��������������������������������������������������������������������38
■Erasing/transferring bank contents ����������������������������������������39
7 SCAN OPERATION ···························································· 40–47
■Scan types�����������������������������������������������������������������������������40
■Full/band/programmed scan �������������������������������������������������42
■Scan edges programming������������������������������������������������������43
■Memory scan ������������������������������������������������������������������������44
■Memory bank scan ����������������������������������������������������������������45
■Skip channel/frequency setting����������������������������������������������46
■Scan resume setting��������������������������������������������������������������47
8 PRIORITY WATCH······························································48–50
■Priority watch types ���������������������������������������������������������������48
■Priority watch operation ���������������������������������������������������������49
9 SET MODES ·······································································51–64
■General ������������������������������������������������������������������������������51
■Set mode item list ������������������������������������������������������������������52
■Initial set mode item list ���������������������������������������������������������52
■Set mode items����������������������������������������������������������������������53
■Initial set mode items�������������������������������������������������������������59
10 OTHER FUNCTIONS ··························································65–75
■Programming a DTMF code sequence����������������������������������65
■Transmitting a DTMF code sequence ������������������������������������66
■Setting DTMF transfer speed�������������������������������������������������67
■Tone frequency and DTCS code�������������������������������������������� 68
■Tone/DTCS squelch���������������������������������������������������������������70
■Tone scan�������������������������������������������������������������������������������71
■Weather channel operation����������������������������������������������������72
■Cloning function���������������������������������������������������������������������74
■Resetting��������������������������������������������������������������������������������75
11 TROUBLESHOOTING ······························································76
12 SPECIFICATIONS·····································································77
13 OPTIONS ············································································78–82
■VOX function ��������������������������������������������������������������������������80
■Remote control function���������������������������������������������������������82
14 COUNTRY CODE LIST·····························································83
INDEX ·····················································································84–87
TABLE OF CONTENTS 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

1
New2001New2001
ACCESSORY ATTACHMENT
1
New2001
■Hand strap
To facilitate carrying the
transceiver, slide the hand
strap through the loop on
the top of the rear panel as
illustrated at the right.
■Belt clip
To attach the belt clip:
Slide the belt clip in the
direction of the arrow
until the belt clip locks in
place, and makes a ‘click’
sound.
To detach the belt clip:
qRemove the battery pack from the transceiver, if it is at-
tached. (p. 2)
wLift the tab up (q), and slide the belt clip in the direction
of the arrow (w).
qw
Handstrap

New2001
2
1
ACCESSORY ATTACHMENT
New2001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
■Battery pack
To attach the battery pack:
qFit the battery pack
in the direction of the
arrow (q), then close.
w Hook the latch until it
makes a ‘click’ sound
(w).
• Charge the battery pack
before use. (pp. 12–14)
To detach the battery pack:
Be careful! The latch is tightly locked, so use caution
when releasing it. DO NOT use your finger nail. Use the
edge of a coin or screwdriver tip to carefully release it.
Unhook the latch (e),
and lift up the battery
pack in the direction of
the arrow (r).
■Antenna
Insert the antenna connector into the antenna base and
tighten the antenna screw.
Jack cover
• NEVER carry the transceiver by holding only the an-
tenna.
• When the jack is not in use, keep the jack cover in place
to protect the connector from dust and moisture.
✔For your information
Third-party antennas may increase transceiver
performance. An optional AD-92SMA antenna
connector adapter is available to connect an antenna
that has a BNC connector.
w
q
Latch
Battery pack/Battery case
e
r
Latch
Battery pack/Battery case

3
New2001New2001
PANEL DESCRIPTION
2
New2001
■Front, top and side panels
Speaker
ANTENNA
CONNECTOR
EXTERNAL
DC IN JACK
VOLUME
CONTROL
CONTROL DIAL
EXTERNAL SPEAKER/
MICROPHONE JACKS
Keypad (pp. 4, 5)
Internal microphone
Function display (pp. 6, 7)
PTT SWITCH
e
r
y
w
q
t
qANTENNA CONNECTOR (p. 2)
Connects to the supplied antenna.
• An optional AD-92SMA adapter (p. 79) is available for connect-
ing an antenna with a BNC connector.
w EXTERNAL SPEAKER/MICROPHONE JACKS [SP/MIC]
Connect an optional speaker microphone, cloning cable,
or headset, if desired.
See page 79 for a list of available options.
Be sure to turn power OFF before connecting or dis-
connecting optional equipment to/from the [SP/MIC]
jack.
eCONTROL DIAL [DIAL]
➥Rotate to select the operating frequency. (p. 19)
➥During memory mode operation, rotate to select the
memory channel. (pp. 18, 30)
➥While scanning, changes the scanning direction.
(pp. 42, 44, 45)
➥While continuing to push [MONI](BAND), sets the
squelch level. (p. 17)
➥After pushing [BAND] during memory mode operation,
selects the programmed bank. (p. 33)
➥During set mode operation, rotate to select the set
items. (p. 51)

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
New2001
A-6808H-1EX-t
Printed in Japan
© 2009–2016 Icom Inc.
Printed on recycled paper with soy ink.
<Intended Country of Use>
■AT ■BE ■CY ■CZ ■DK ■EE
■FI ■FR ■DE ■GR ■HU ■IE
■IT ■LV ■LT ■LU ■MT ■NL
■PL ■PT ■SK ■SI ■ES ■SE
■GB ■IS ■LI ■NO ■CH ■BG
■RO ■TR ■HR
#02 EUR
<Intended Country of Use>
■AT ■BE ■CY ■CZ ■DK ■EE
■FI ■FR ■DE ■GR ■HU ■IE
■IT ■LV ■LT ■LU ■MT ■NL
■PL ■PT ■SK ■SI ■ES ■SE
■GB ■IS ■LI ■NO ■CH ■BG
■
RO ■TR ■HR
#03 UK
<Intended Country of Use>
■AT ■BE ■CY ■CZ ■DK ■EE
■FI ■FR ■DE ■GR ■HU ■IE
■IT ■LV ■LT ■LU ■MT ■NL
■PL ■PT ■SK ■SI ■ES ■SE
■GB ■IS ■LI ■NO ■CH ■BG
■
RO ■TR ■HR
#12 RSP
Other manuals for IC-T70A
4
This manual suits for next models
1
Table of contents
Other Icom Transceiver manuals