Icom IC-V80 User manual

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
INSTRUCTION MANUAL
iV80
iV80 E
VHF TRANSCEIVER
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE
CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS
PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

i
FOREWORD
Thank you for purchasing this fine Icom product. The IC-V80/
V80E vhf transceiver is designed and build with Icom’s
superior technology and craftsmanship. With proper care,
this product should provide you with years of trouble-free
operation.
We want to take a couple of moments of your time to thank
you for making your IC-V80/V80E your radio of choice, and
hope you agree with Icom’s philosophy of “technology first.”
Many hours of research and development went into the
design of your IC-V80/V80E.
FEATURES
❍Dust-protection/Splash-resistant
construction (IP54*)
 *Only when the battery pack/case, antenna and jack cover are
attached.
❍Built in VOX circuit enabling the VOX
operation* (voice operated transmission)
 *To use the VOX operation, an optional headset and a plug
adapter cable are additionally required.
EXPLICIT DEFINITIONS
WORD DEFINITION
RDANGER! Personal death, serious injury or an ex-
plosion may occur.
RWARNING! Personal injury, fire hazard or electric
shock may occur.
CAUTION Equipment damage may occur.
NOTE Recommended for optimum use. No risk
of personal injury, fire or electric shock.
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This
instruction manual contains important operating instructions
for the IC-V80/V80E.

ii
RWARNING RF EXPOSURE! This device emits
Radio Frequency (RF) energy. Caution should be observed
when operating this device. If you have any questions re-
garding RF exposure and safety standards, please refer to
the Federal Communications Commission Office of Engi-
neering and Technology’s report on Evaluating Compliance
with FCC Guidelines for Human Radio Frequency Electro-
magnetic Fields (OET Bulletin 65)
RWARNING! NEVER hold the transceiver so that
the antenna is very close to, or touching exposed parts of
the body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm
(2 to 4 inches) away from the lips and the transceiver is ver-
tical.
RWARNING! NEVER operate the transceiver with
a headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume op-
eration. If you experience a ringing in your ears, reduce the
volume level or discontinue use.
RWARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention—
anything less may result in an accident.
NEVER connect the transceiver to a power source using
reverse polarity. This will ruin the transceiver.
DO NOT operate the transceiver near unshielded electri-
cal blasting caps or in an explosive atmosphere.
DO NOT push [PTT] unless you actually intend to trans-
mit.
BE CAREFUL! The transceiver will become hot when
operating it continuously for long periods.
DO NOT use or place the transceiver in direct sunlight
or in areas with temperatures below –20°C (–4˚F) or above
+60°C (+140˚F).
Place the unit in a secure place to avoid inadvertent use by
children.
DO NOT use harsh solvents such as benzene or alco-
hol to clean the transceiver, because they can damage the
transceiver’s surfaces.
PRECAUTIONS

iii
FCC INFORMATION
• FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential
installation. This equipment generates, uses and can radi-
ate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and re-
ceiver.
• Connect the equipment into an outlet on a circuit differ-
ent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
PRECAUTIONS
KEEP the transceiver away from heavy rain, and never
immerse in the water. The transceiver meets IP54* require-
ments for dust-protection and splash resistance. However,
once the transceiver has been dropped, dust-protection and
splash resistance cannot be guaranteed because of possible
damage to the transceiver’s case or the waterproof seal.
* Only when the battery pack/case, antenna and jack cover are at-
tached.
NEVER operate or touch the transceiver with wet hands.
This may result in an electric shock or may damage the
transceiver.
Even when the transceiver power is OFF, a slight current still
flows in the circuits. Remove the battery pack or batteries
from the transceiver when not using it for a long time. Oth-
erwise, the installed battery pack or batteries will become
exhausted, and will need to be recharged or replaced.
Approved Icom optional equipment is designed for optimal
performance when used with an Icom transceiver.
Icom is not responsible for the destruction or damage to an
Icom transceiver in the event the Icom transceiver is used
with equipment that is not manufactured or approved by
Icom. CAUTION: Changes or modifications to this device, not
expressly approved by Icom Inc., could void your authority
to operate this device under FCC regulations.

iv
Icom, Icom Inc. and the Icom logo are registered trademarks of
Icom Incorporated (Japan) in Japan, the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other countries.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Microsoft, Windows and Windows Vista are registered trademarks of
Microsoft Corporation in the United States and/or other countries.
SUPPLIED ACCESSORIES
The following accessories are supplied with the transceiver.
AntennaBattery pack*
Belt clip*
Jack cover
(with screws)
Battery charger* AC adapter*
* Not supplied, or the shape is different,
depending on the version.

v
TABLE OF CONTENTS
FOREWORD ..................................................................................... i
FEATURES........................................................................................ i
EXPLICIT DEFINITIONS................................................................... i
IMPORTANT...................................................................................... i
PRECAUTIONS............................................................................ ii–iii
FCC INFORMATION ....................................................................... iii
SUPPLIED ACCESSORIES............................................................ iv
TABLE OF CONTENTS............................................................... v–vi
1 ACCESSORIES ...........................................................1–2
 ■ Antenna ...................................................................................1
 ■ Belt clip ....................................................................................1
 ■ Battery pack/case ....................................................................2
 ■ Jack cover................................................................................2
2 PANEL DESCRIPTION................................................3–7
 ■■ Front, top and side panels ....................................................... 3
 ■ Function display.......................................................................6
3 BATTERY CHARGING ..............................................8–13
 ■ Caution (for the BP-264 Ni-MH battery) ................................... 8
 ■ Caution (for the BP-265 Li-Ion battery)....................................9
 ■ Battery chargers ....................................................................11
 ■ Battery case (BP-263)............................................................... 13
 ■ Battery information ................................................................13
4 BASIC OPERATION................................................14–19
 ■ Power ON ..............................................................................14
 ■ Adjusting the volume level .....................................................14
 ■ Adjusting the squelch level ....................................................14
 ■ Monitor function .....................................................................14
 ■ Mode selection.......................................................................15
 ■ Operating mode selection......................................................16
 ■ Setting a tuning step..............................................................16
 ■ Setting a frequency................................................................16
 ■ Receiving...............................................................................17
 ■ Transmitting............................................................................17
 ■ Key lock function....................................................................18
 ■ [VOL] function assignment.....................................................18
 ■ Weather channel operation (U.S.A. version only) ..................19
5 REPEATER AND DUPLEX OPERATION ...............20–23
 ■ Repeater operation................................................................20
 ■ Duplex operation....................................................................21
 ■ Subaudible tones ................................................................... 22
 ■ Lockout function.....................................................................23
 ■ Auto repeater function (U.S.A. version only) ......................... 23
6 MEMORY/CALL OPERATION ................................24–28
 ■ General description................................................................24
 ■ Selecting a memory channel .................................................24
 ■ Selecting the Call channel .....................................................24
 ■ Channel programming ...........................................................25
 ■ Copying memory/Call contents..............................................26
 ■ Clearing memory contents.............................................................27
 ■ Display type ...........................................................................27
 ■ Programming a channel name .................................................28

vi
7 SCAN OPERATION.................................................29–31
 ■ Scan types.............................................................................29
 ■■ Programmed scan ................................................................29
 ■ Memory Scan ........................................................................30
 ■ Setting skip channels.............................................................30
 ■ Scan resume setting..............................................................30
 ■ Priority watch .........................................................................31
8 TONE SQUELCH AND POCKET BEEP .................32–34
 ■ Tone/DTCS squelch and pocket beep....................................32
 ■ Tone scan...............................................................................34
9 DTMF MEMORY ...................................................... 35–37
 ■ Programming a DTMF code sequence..................................35
 ■ Transmitting a DTMF code sequence ....................................36
 ■ Confirming a DTMF memory .................................................37
 ■ Setting DTMF transfer speed.................................................37
10 SET MODES............................................................38–47
 ■ Set mode programming .........................................................38
 ■ Set mode items......................................................................39
 ■ Initial Set mode programming................................................... 43
 ■ Initial Set mode items ............................................................44
11 CLONING ......................................................................48
 ■ Cloning operation...................................................................48
12 RESETTING ..................................................................49
 ■ Resetting................................................................................49
13 TROUBLE SHOOTINGTROUBLE SHOOTING..................................................50
14
OPTIONS.................................................................51–53
 ■ VOX function ..........................................................................52
15 SPECIFICATIONS .........................................................54
16
CE ............................................................................55–56
TABLE OF CONTENTS 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

11
■Antenna
Insert the antenna into the antenna connector and twist the
antenna to lock it in place.
CAUTION:
•
NEVER HOLD just the antenna when carrying the trans-
ceiver.
• Transmitting without an antenna will damage the trans-
ceiver.
■Belt clip
To attach the belt clip:
➥Slide the belt clip in the direction of the arrow until the belt
clip locks in place, and makes a ‘click’ sound.
To detach the belt clip:
qRemove the battery pack/case from the transceiver, if it is
attached. (p. 2).
wLift the tab up (q), and slide the belt clip in the direction
of the arrow (w).
ACCESSORIES
1
Belt clip
Battery pack/case
q
w

2
1
■Battery pack/case
To attach the battery pack/case:
qFit the battery pack/case in the direction of the arrow (q),
then close.
wHook the latch until it makes a ‘click’ sound (w).
To remove the battery pack/case:
Be careful! The latch is tightly locked, so use caution
when releasing it. DO NOT use your finger nail. Use the
edge of a coin or screwdriver tip to carefully release it.
➥Unhook the latch (e), and lift up the battery pack/case in
the direction of the arrow (r).
NEVER remove or attach the battery pack/case when the
transceiver is wet or soiled. This may result in water or
dust getting into the transceiver/battery pack/case, and
may result in them being damaged.
NOTE: Keep the battery terminals clean. It’s a good idea
to clean the battery terminals once a week.
■Jack cover
Attach the jack cover when optional equipment is not used.
1
ACCESSORIES
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
To attach the jack cover
qAttach the jack cover to
the [SP MIC] jack.
wTighten the screws.
To detach the jack cover
eRemove the screws with a
phillips screwdriver.
rDetach the jack cover to
connect optional equip-
ment.
w
q
Latch
Battery pack/case
e
r
r
w
w
q
e
e

3
PANEL DESCRIPTION
2
■Front, top and side panels
qPTT SWITCH [PTT]
➥Push and hold to transmit, release to receive. (p. 17)
For IC-V80E only
➥Push briefly, then push and hold to transmit a 1750 Hz
tone burst signal. (p. 22)
wANTENNA CONNECTOR
Connect the antenna here. (p. 1)
eCONTROL DIAL [VOL]
➥Adjust the volume level. (p. 14)
➥During the Set mode, or Initial Set mode, rotate to se-
lect a desired option or value. (pp. 38, 43)
rEXTERNAL SPEAKER/MICROPHONE JACKS [SP MIC]
Used to connect an optional speaker-microphone, plug
adapter cable or cloning cable. The internal microphone
and speaker will not function when an option is con-
nected. See page 51 for a list of available options.
Be sure to turn power OFF before connecting/discon-
necting optional equipment to/from the [SP/MIC] jack.
tMONITOR KEY [MONI]
➥Push and hold to open the squelch temporarily to mon-
itor the operating frequency. (p. 14)
➥While pushing and holding this key, push []or []to
adjust the squelch level. (p. 14)
➥Enters or sends the DTMF code ‘A.’ (pp. 35, 36)
q
we
r
t
y
u
i
Function
display (p. 6)
Keypad (p. 4)
Microphone
Speaker

4
2
yPOWER KEY [ ]
Push and hold for 1 sec. to turn the transceiver power ON
or OFF. (p. 14)
uUP/DOWN KEYS []/[]
➥Push to change the operating frequency. (p. 16)
➥During memory mode operation, push to select a
memory channel. (p. 24)
➥While scanning, push to change the scanning direction.
(pp. 29, 30, 31, 34)
➥While pushing and holding [MONI], push to set the
squelch level. (p. 14)
➥During the Set mode, or Initial Set mode, push to se-
lect a desired setting item. (pp. 38, 43)
➥[] enters or sends the DTMF code ‘B.’ (pp. 35, 36)
➥[] enters or sends the DTMF code ‘C.’ (pp. 35, 36)
iVFO/MEMORY/CALL KEY [VFO/MR/CALL]
➥Push to select the VFO mode, memory mode, a Call
channel and a weather channel*, in sequence. (p. 15)
*Only the U.S.A. version transceivers.
➥After pushing [FUNC](M), push to enter the memory
programming mode.
➥After pushing [FUNC](M), push and hold for 1 sec. to
transfer a channel contents to a memory channel, or to
the VFO mode. (p. 26)
➥Enters or sends the DTMF code ‘D.’ (pp. 35, 36)
The functions of [VOL] and []/[]can be exchanged.
See page 18 for details.
DKEYPAD
➥Push to input numbers for frequency input and memory
channel selection.
➥Push to enter or send the DTMF code. (pp. 35, 36)
➥To activate the second function of a key, first push
[FUNC](M), and then push the key.
[1] • [ TONE](1)
➥Numeric input and DTMF code: ‘1’
➥After pushing [FUNC](M), selects the Tone func-
tion. (p. 33)
[2] • [VOX](2)
➥Numeric input and DTMF code: ‘2’
➥After pushing [FUNC](M), turns the VOX function
ON or OFF*. (p. 52)
* Only when an optional headset and plug adapter are
connected.
2
PANEL DESCRIPTION
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

5
[3] • [T.SCAN](3)
➥Numeric input and DTMF code: ‘3’
➥After pushing [FUNC](M), starts a tone scan.
(p. 34)
[4] • [DUP](4)
➥Numeric input and DTMF code: ‘4’
➥After pushing [FUNC](M), selects minus duplex,
plus duplex, or simplex operation. (p. 21)
[5] • [SCAN](5)
➥Numeric input and DTMF code: ‘5’
➥After pushing [FUNC](M), starts a scan. (pp. 29,
30)
[6] • [SKIP](6)
➥Numeric input and DTMF code: ‘6’
➥After pushing [FUNC](M), sets or cancels the
skip setting. (p. 30)
[7] • [PRIO](7)
➥Numeric input and DTMF code: ‘7’
➥After pushing [FUNC](M), starts a priority watch.
(p. 31)
[8] • [SET](8)
➥Numeric input and DTMF code: ‘8’
➥After pushing [FUNC](M), enters the Set mode.
(p. 38)
[9] • [H/M/L](9)
➥Numeric input and DTMF code: ‘9’
➥After pushing [FUNC](M), selects the output
power between high, middle and low. (p. 17)
[0] • [DTMF-M](0)
➥Numeric input and DTMF code: ‘0’
➥After pushing [FUNC](M), enters the DTMF
memory mode. (p. 35)
[M] • [FUNC](M)
➥DTMF code: ‘M(indication: E)’
➥Push to access the second function of other keys.
[# ENT] • [ ](# ENT)
➥DTMF code: ‘#(indication: F)’
➥After entering a frequency, stores the frequency.
(p. 16)
➥Push to exit the Set mode or Initial Set mode.
(pp. 38, 43)
➥ After pushing [FUNC](M), push and hold for 1 sec.
to turn the key lock function ON or OFF (p. 18)
2PANEL DESCRIPTION

6
2
■Function display
qBUSY INDICATOR
➥Appears when a signal is being received, or the
squelch is open.
➥Blinks while the monitor function is ON. (p. 14)
wSIGNAL INDICATOR
➥Shows the strength of the received signal. (p. 17)
➥While transmitting, shows the output power level.
(p. 17)
eTONE INDICATOR
➥“ ” appears while the repeater tone encoder is ON.
(p. 20)
➥“ ” appears while the tone squelch function is ON.
(p. 33)
➥“
D
” appears while the DTCS squelch function is ON.
(p. 33)
➥“ ” appears with the “ ” or “
D
” indicator while the pocket
beep function (with CTCSS or DTCS) is ON. (p. 33)
rMEMORY INDICATOR
Appears when the memory mode is selected. (pp. 15, 24)
tFREQUENCY READOUT
➥Displays the operating frequency, memory channel,
Set modes contents and a variety of other information.
• The decimal point blinks during scan.
➥During memory mode operation, the programmed
memory name is displayed.
yBATTERY INDICATOR (p. 13)
➥“ ” (battery indicators) appear when the battery
pack/case is attached.
➥“ ” appears when the battery pack must be changed,
or batteries must be replaced.
2
PANEL DESCRIPTION
Weak RX Signal level Strong
Low Middle High
u
i
o
q w e r y
t
!5
!4
!3
!1!2 !0
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

7
uKEY LOCK INDICATOR
Appears when the key lock function is ON. (p. 18)
iVOX INDICATOR
Appears when the VOX function is ON. (p. 52)
oPOWER INDICATOR (p. 17)
➥“H” appears when high power is selected.
➥“M” appears when middle power is selected.
➥“L” appears when low power is selected.
!0MEMORY CHANNEL NUMBER INDICATOR
➥Displays the selected memory channel number. (p. 24)
➥“C” appears when the Call channel is selected. (p. 24)
!1AUTO POWER OFF INDICATOR
Displays when the Auto Power OFF function is ON. (p. 44)
!2DUPLEX INDICATOR (p. 21)
➥“+” appears when plus duplex is selected.
➥“–” appears when minus duplex is selected.
!3SKIP INDICATOR
Appears when the selected memory channel is set as a
skip channel. (p. 30)
!4FUNCTION INDICATOR
Appears when the second function can be accessed.
!5TRANSMIT INDICATOR
Appears while transmitting. (p. 17)
2PANEL DESCRIPTION

8
2
3
3
BATTERY CHARGING
■Caution (for the BP-264 Ni-MH battery)
RDANGER! NEVER short terminals (or charging terminals)
of the battery pack. Also, current may flow into nearby metal
objects such as a necklace, so be careful when placing bat-
tery packs (or the transceiver) in handbags, etc.
Simply carrying with or placing near metal objects such as
a necklace, etc. may cause shorting. This may damage not
only the battery pack, but also the transceiver.
RDANGER! NEVER incinerate used battery packs. Internal
battery gas may cause an explosion.
RDANGER! NEVER immerse the battery pack in water.
If the battery pack becomes wet, be sure to wipe it dry BE-
FORE attaching it to the transceiver.
CAUTION: Always use the battery within the specified tem-
perature range, –5˚C to +60˚C (+23˚F to +140˚F). Using the
battery out of its specified temperature range will reduce the
battery’s performance and battery life.
CAUTION: Shorter battery life could occur if the battery is
left completely discharged, or in an excessive temperature
environment (above +55˚C; +131˚F) for an extended period
of time. If the battery must be left unused for a long time,
it must be detached from the radio after charging. Keep it
safely in a cool dry place at the following temperature range:
–20˚C to +45˚C (–4˚F to +113˚F) (up to a month)
–20˚C to +35˚C (–4˚F to +95˚F) (up to six months)
–20˚C to +25˚C (–4˚F to +77˚F) (up to a year*)
* We recommend charging the battery pack every 6 months.
Clean the battery terminals to avoid rust or misscontact.
Keep battery terminals clean. It’s a good idea to clean bat-
tery terminals once a week.
If your Ni-MH battery pack seems to have no capacity, even
after being charged, completely discharge it by leaving the
power ON overnight. Then, fully charge the battery pack again.
If the battery pack still does not retain a charge (or only very lit-
tle charge), a new battery pack must be purchased. (p. 51)
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation.
• Recommended temperature range for charging:
between +10°C and +40°C (rapid charge: with BC-191) or
between 0°C and +45°C (regular charge: with BC-192)
• Use the supplied charger or optional charger (BC-191 for
rapid charging, BC-192 for regular charging) only. NEVER
use other manufacturers’ chargers.
The battery pack contains a rechargeble battery.
Charge the battery pack before first operating the trans-
ceiver, or when the battery pack becomes exhausted.
If you want to prolong the battery life, the following points
should be observed:
• Avoid over charging. The charging time period should be
less than 48 hours.
• Use the battery pack until it becomes almost completely
exhausted, under normal conditions. We recommend bat-
tery charging after transmitting becomes impossible.
1
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

9
■Caution (for the BP-265 Li-Ion battery)
RDANGER! Use and charge only specified Icom battery
packs with Icom radios or Icom chargers. Only Icom battery
packs are tested and approved for use with Icom radios or
charged with Icom chargers. Using third-party or counterfeit
battery packs or chargers may cause smoke, fire, or cause
the battery to burst.
DBattery caution
RDANGER! DO NOT hammer or otherwise impact the bat-
tery. Do not use the battery if it has been severely impacted
or dropped, or if the battery has been subjected to heavy
pressure. Battery damage may not be visible on the outside
of the case. Even if the surface of the battery does not show
cracks or any other damage, the cells inside the battery may
rupture or catch fire.
RDANGER! NEVER use or leave battery pack in areas
with temperatures above +60˚C (+140˚F). High tempera-
ture buildup in the battery, such as could occur near fires
or stoves, inside a sun heated car, or in direct sunlight may
cause the battery to rupture or catch fire. Excessive temper-
atures may also degrade battery performance or shorten
battery life.
RDANGER! DO NOT expose the battery to rain, snow, sea-
water, or any other liquids. Do not charge or use a wet battery.
If the battery gets wet, be sure to wipe it dry before using.
RDANGER! NEVER incinerate a used battery pack since
internal battery gas may cause it to rupture, or may cause
an explosion.
RDANGER! NEVER solder the battery terminals, or
NEVER modify the battery pack. This may cause heat gener-
ation, and the battery may burst, emit smoke or catch fire.
RDANGER! Use the battery only with the transceiver for
which it is specified. Never use a battery with any other
equipment, or for any purpose that is not specified in this in-
struction manual.
RDANGER! If fluid from inside the battery gets in your
eyes, blindness can result. Rinse your eyes with clean water,
without rubbing them, and see a doctor immediately.
R WARNING! Immediately stop using the battery if it emits
an abnormal odor, heats up, or is discolored or deformed. If
any of these conditions occur, contact your Icom dealer or
distributor.
R WARNING! Immediately wash, using clean water, any
part of the body that comes into contact with fluid from in-
side the battery.
3BATTERY CHARGING
Misuse of Li-Ion batteries may result in the following haz-
ards: smoke, fire, or the battery may rupture. Misuse can
also cause damage to the battery or degradation of battery
performance.

10
3
3
BATTERY CHARGING
R WARNING! NEVER put the battery in a microwave oven,
high-pressure container, or in an induction heating cooker.
This could cause a fire, overheating, or cause the battery to
rupture.
CAUTION: Always use the battery within the specified tem-
perature range, –20˚C to +60˚C (–4˚F to +140˚F). Using the
battery out of its specified temperature range will reduce the
battery’s performance and battery life.
CAUTION: Shorter battery life could occur if the battery is
left fully charged, completely discharged, or in an excessive
temperature environment (above +50˚C; +122˚F) for an ex-
tended period of time. If the battery must be left unused for a
long time, it must be detached from the radio after discharg-
ing. You may use the battery until the battery indicator shows
half-capacity, and then keep it safely in a cool dry place at
the following temperature range:
–20˚C to +50˚C (–4˚F to +122˚F) (up to a month)
–20˚C to +35˚C (–4˚F to +95˚F) (up to three months)
–20˚C to +20˚C (–4˚F to +68˚F) (up to a year)
DCharging caution
RDANGER! NEVER charge the battery pack in areas with
extremely high temperatures, such as near fires or stoves,
inside a sun-heated vehicle, or in direct sunlight. In such en-
vironments, the safety/protection circuit in the battery will ac-
tivate, causing the battery to stop charging.
R WARNING! DO NOT charge or leave the battery in the
battery charger beyond the specified time for charging. If the
battery is not completely charged by the specified time, stop
charging and remove the battery from the battery charger.
Continuing to charge the battery beyond the specified time
limit may cause a fire, overheating, or the battery may rup-
ture.
R WARNING! NEVER insert the transceiver (battery at-
tached to the transceiver) into the charger if it is wet or
soiled. This could corrode the battery charger terminals or
damage the charger. The charger is not waterproof.
CAUTION: DO NOT charge the battery outside of the spec-
ified temperature range: BC-193 (+10˚C to +40˚C; +50˚F
to +104˚F). Icom recommends charging the battery at +20˚C
(+68˚F). The battery may heat up or rupture if charged out of
the specified temperature range. Additionally, battery perfor-
mance or battery life may be reduced.
The supplied battery pack, charger, and AC adapter dif-
fer, or no supplied depending on the version.
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation.
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

11
■Battery chargers
D Using the BC-191 to rapid charge the BP-264
The BC-191 provides rapid charging of only the BP-264 Ni-MH
battery pack. Never use it to charge any other battery pack.
Charging time: Approx. 2 hours
The following item is additionally required:
• An AC adapter (not supplied with some versions) or the OPC-515L
or CP-23L DC power cable.
DUsing the BC-192 to regular charge the BP-264
The BC-192 provides regular charging of only the BP-264
Ni-MH battery pack. Never use it to charge any other battery
pack.
Charging time (with the 147S): Approx. 16 hours
The following item is additionally required:
• An AC adapter (not supplied with some versions) or the OPC-515L
DC power cable.
3BATTERY CHARGING
The optional OPC-
515L (for DC power
source) can be
used instead of the
AC adapter.
Charge indicator
• Lights green while charging.
NOTE:
The charge indicator will not
go out even after a battery
pack is fully charged.
AC adapter
(A different type, or no AC
adapter is supplied, de-
pending on the version.)
Transceiver
Turn power OFF
Battery pack
Screws*
(Self tapping screw:
M3.5 × at least 30 mm)
*Purchase separately.
Using screws is
recommended to
secure the charger.
Charging time period differs
depending on the input voltage.
12 V : Approx. 36 hours
13.8 V : Approx. 21 hours
16 V : Approx. 16 hours
The optional OPC-
515L (for DC power
source) or CP-23L
(for 12 V cigarette
lighter socket) can
be used instead of
the AC adapter.
Charge indicator
• Lights orange : While charging
• Lights green : Charging is completed.
AC adapter
(A different type, or no AC
adapter is supplied, de-
pending on the version.)
Transceiver
Turn power OFF
Battery pack
Screws*
(Self tapping screw:
M3.5 × at least 30 mm)
*Purchase separately.
Using screws is
recommended to
secure the charger.

12
3
3
BATTERY CHARGING
D Using the BC-193 to rapid charge the BP-265
The BC-193 provides rapid charging of only the BP-265 Li-
Ion battery pack. Never use it to charge any other battery
pack.
Charging time: Approx. 2.5 hours
The following item is additionally required:
• An AC adapter (not supplied with some versions) or the OPC-515L
or CP-23L DC power cable.
IMPORTANT: Battery charging caution
Ensure the tabs on the battery pack are correctly aligned
with the guide rails inside the charger.
CAUTION: When using the OPC-515L DC power cable
NEVER connect the OPC-515L to a power source using
reverse polarity. This will ruin the battery charger.
White line:
+
Black line:
–
The optional OPC-
515L (for DC power
source) or CP-23L
(for 12 V cigarette
lighter socket) can
be used instead of
the AC adapter.
AC adapter
(A different type, or no AC
adapter is supplied, de-
pending on the version.)
Transceiver
Turn power OFF
Battery pack
Screws*
(Self tapping screw:
M3.5 × at least 30 mm)
*Purchase separately.
Using screws is
recommended to
secure the charger.
Charge indicator
• Lights orange : While charging
• Lights green : Charging is completed.
Guide rail
Tabs
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

13
■Battery case (BP-263)
When using the battery case (BP-263), install 6 ×AA (LR6)
size alkaline batteries, as described below.
qRemove the battery case if it is attached. (p. 2)
wInstall 6 × AA (LR6) size alkaline batteries.
• Install only alkaline batteries.
• Be sure to observe the correct polarity.
eAttach the battery case. (p. 2)
CAUTION:
• When installing batteries, make sure they are all the same
brand, type and capacity. Also, do not mix new and old bat-
teries together.
• Keep battery terminals clean. It’s a good idea to clean bat-
tery terminals once a week.
• Never incinerate used battery cells since the internal bat-
tery gas may cause them to rupture.
• Never expose a detached battery case to water. If the battery
case gets wet, be sure to wipe it dry before using it.
• Never use batteries whose insulated covering is damaged.
NOTE: When the battery case is attached, the battery
protection function must be turned OFF in the Initial Set
mode (p. 47).
■Battery information
DBattery life
Even when the transceiver power is OFF, a small current
still flows in the transceiver. Remove the battery pack/case
when it won’t be used for a long time. Otherwise, the battery
pack or the batteries in the case will become exhausted.
DBattery indication
The battery indicator, “ ,” appears when a battery pack/
case is attached to the transceiver.
3BATTERY CHARGING
Battery pack/case Voltage Capacity Battery life*1
BP-263 Battery case for
AA (LR6) × 6 alkaline —*2
BP-264 7.2 V 1400 mAh 13 hrs.
BP-265 7.4 V 1900 mAh (min.)
2000 mAh (typ.) 19 hrs.
*1 When the power save function is set to “P–S.At,” and the operating
time is calculated under the following conditions;
TX : RX : standby = 5 : 5 : 90
*2The average operating life depends on the alkaline cells used.
Indicator Battery condition
The battery has ample capacity.
The battery is nearing exhaustion.
Charging the battery pack, or replacing the batteries
in the case is necessary.
Be careful! The negative
terminals of the battery case
protrude from the body, so
pay attention not to injure
your fingers when inserting
the batteries.