Icom IC-F5060 Series User manual

OPERATING GUIDE
OPERATING GUIDE FOR
IC-F5060/F6060 SERIES
BIIS 1200/MDC 1200 SYSTEM/
LTR®/IDAS™ OPERATION

i
Thank you for purchasing this Icom transceiver.
The BIIS 1200/MDC 1200 system/LTR®/IDAS™ (Icom Digital
Advanced System) functions are built into your IC-F5060/
F6060 series transceiver.
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS OPERATING GUIDE — This operating
guide contains important operating instructions for:
• IC-F5061/F5061D/F5062/F5063 VHF MOBILE TRANS-
CEIVERS
• IC-F6061/F6061D/F6062/F6063 UHF MOBILE TRANS-
CEIVERS
NOTE: In this operating guide, the LCD illustration is de-
scribed using the 2 line display mode.
INFORMATION: The 10-key pad of the optional DTMF mi-
crophone (HM-148T) has only the DTMF code transmitting
capability, so an ID and message cannot be input with this
microphone.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-
porated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
IDAS and IDAS logo are trademarks of Icom Incorporated (Japan).
LTR is a registered trademark of the E.F.Johnson Technologies, INC. in the
United States.
All other products or brands are registered trademarks or trademarks of their
respective holders.
IMPORTANT

TABLE OF CONTENTS
ii
IMPORTANT.......................................................................... i
TABLE OF CONTENTS........................................................ ii
1 PREPARATION............................................................1−2
 ■ Programmable function keys ........................................1
2 BIIS 1200 OPERATION .............................................3−15
 ■ Setting example............................................................3
 ■ Receiving a call ............................................................3
 ■ Transmitting a call.........................................................6
 ■ Receiving a message...................................................8
 ■ Transmitting a status...................................................10
 ■ Transmitting an SDM ..................................................11
 ■ Position data transmission..........................................12
 ■ Printer connection ......................................................13
 ■ BIIS ANI .....................................................................13
 ■ Transmitting an Emergency call..................................13
 ■ Stun function ..............................................................14
 ■ BIIS indicators ............................................................14
 ■ Priority A channel selection........................................14
 ■ Horn output ................................................................15
3 MDC 1200 SYSTEM OPERATION ..........................16−23
 ■ MDC 1200 system operation......................................16
 ■ Receiving a call ..........................................................16
 ■ Transmitting a call.......................................................19
 ■ Status message transmission ....................................23
4 LTR OPERATION ....................................................24−25
 ■ LTR operation.............................................................24
 ■ Receiving a call ..........................................................24
 ■ Transmitting a call.......................................................25
5 IDAS OPERATION ..................................................26−46
 ■ IDAS operation ...........................................................26
 ■ IDAS-Trunk operation .................................................26
 ■ Receiving a call ..........................................................26
 ■ Transmitting a call.......................................................32
 ■ Transmitting Position data...........................................44
 ■ Sending a Status message ........................................45
 ■ Sounding a Horn ........................................................45
 ■ Connecting a printer...................................................45
 ■ Encryption function.....................................................45
 ■ ATB Ring Back function..............................................46

1
1PREPARATION
■Programmable function keys
The following functions can be assigned to the [UP], [DOWN],
[P0], [P1], [P2], [P3] and [P4] programmable function keys.
Consult your Icom dealer or system operator for details con-
cerning your transceivers programming.
If the programmable function names are bracketed in the fol-
lowing explanations, the specific key is used to activate the
function.
DFor BIIS 1200 operation only
BIIS BUTTON KEY
➥Push to toggle the call ID list, transmit message and stand-
by modes.
➥Push to toggle between the queue channel and the received
message record display, after the queue channel is select-
ed.
➥Hold down for 1 second to select the queue channel
mode.
STATUS UP/DOWN KEYS
➥While in standby, push to display the transmit status screen
and select a status number.
➥When a received SDM (Short Data Message) is displayed,
push to cancel the automatic scroll and then manually
scroll the message.
➥When an SDM that contains more than 12 characters is
displayed, push to manually scroll the message.
DFor MDC 1200 system operation only
MDC CALL KEY
➥Push to enter the MDC menu selection mode.
➥Push [CH Up] or [CH Down] to select the desired
“SELCALL,” “CALALERT,” “STUN,” “REVIVE,”
“RADIOCHK,” “STATUS”, “MSG” and “CALL LOG” MDC
menu.
After selecting, push this key again to enter the transceiver
alias selection mode.
• If no operation is performed for approximately 15 seconds, the
transceiver returns to the normal operating mode.
➥In the transceiver alias selection mode, push to return to the
MDC menu selection mode.
MDC SELCALL KEY
Push to enter the transceiver alias selection mode for a
SelCall.
• After selecting the desired alias, push [PTT] to transmit a SelCall.
• If no operation is performed for approximately 15 seconds, the trans-
ceiver returns to the normal operating mode.
MDC CALLALERT KEY
Push to enter the transceiver alias selection mode for a
CallAlert.
• After the desired alias selection, push [PTT] to transmit a Call
Alert.
• If no operation is performed for approximately 15 seconds, the trans-
ceiver returns to the normal operating mode.

DFor LTR operation only
PHONE KEY
Push to connect or disconnect the telephone network.
DFor IDAS operation only
DIGITAL BUTTON KEY
➥Push to enter the application selection mode.
➥Hold down for 1 second to toggle the call type between
Individual and Talkgroup, and then automatically enter the
application selection mode.
• Push [CH Up] or [CH Down] to select the desired “VOICE,”
“CALALERT,” “STUN,” “KILL,” “REVIVE,” “ REM MON,”
“RADIOCHK,” “STATUS,” “ MSG,” “STAT POL” and “CALL LOG”
application.
➥While in the application selection mode, push to enter the
Individual or Talkgroup ID selection mode.
• If “STATUS” or “MSG” is selected as the application, the message
selection mode appears. Push [CH Up] or [CH Down] to select
the desired message, then push the Digital Button key again to
enter the Individual or Talkgroup ID selection mode. (pp. 39, 40)
➥ In the application selection mode, hold down for 1 second
to return to the normal operating mode.
STATUS UP/DOWN KEYS
➥When a received SDM is displayed, push to cancel the
automatic scroll and manually scroll the message.
➥When an SDM that contains more than 12 characters is
displayed, push to manually scroll the message.
10-KEY ENTER KEY
Push to enable the microphone’s 10-key pad operation to se-
lect the memory channel, status message number, and so on,
depending on the presetting. Ask your dealer for details.
2
1
PREPARATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

3
2BIIS 1200 OPERATION
■Setting example
The following key functions are recommended to be assigned
to each programmable key for BIIS 1200 operation. The key
functions can be assigned by your dealer. Ask your dealer for
details.
NOTE: During BIIS 1200 operation, the MDC 1200 sys-
tem, LTR and IDAS operations are disabled.
[Call] : Push to transmit a BIIS call when the
selected channel is an MSK channel.
[BIIS Button] : Push to select the call list ID/transmit
message, or a displayed receive mes-
sage record.
•
The key indicator appears above the key that
this key function is assigned to, while it is acti-
vated. See the instruction manual for details.
[TX Code Enter] : Push to directly enter the ID code
edit mode, then push [CH Up] or [CH
Down] to set the desired digit.
[Moni (Audi)] : When your communication in the MSK
channel mode is finished, push this key
to send a ‘Clear down’ signal.
[CH Up]/[CH Down]: While in the standby mode, push to se-
lect an operating channel.
After pushing [BIIS Button] or
[TX Code CH Enter], push to select a
call list or TX code digit, respectively.
■Receiving a call
DIndividual call
q When an individual call is received:
• Beeps sound.
• “ ” appears and the mute is released.
• “ ” appears or blinks, depending on the presetting.
• Your own ID (or text) and the calling station ID (or text) blink.
0001
1234
Appears or blinksAppears
Your own ID Calling station ID
w Hold down [PTT], then speak into the microphone at your
normal voice level.
• The LED lights red.
e Release [PTT] to return to receive.
• The LED indicator lights green while receiving a signal.
r To end the call, push [Moni(Audi)] to send the ‘Clear
down’ signal.
• Either station can send a ‘Clear down’ signal.
• “CLR DOWN” is displayed for approximately 2 seconds.
• The “ ” icon disappears and the transceiver returns to the
standby mode.

4
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DGroup call
qWhen a group call is received:
• Beeps sound.
• “ ” appears and the mute is released.
• “ ” appears or blinks, depending on the presetting.
• The group ID (or text) and the calling station ID (or text) blink.
4001
1234
Appears or blinksAppears
Group ID Calling station ID
wHold down [PTT], then speak into the microphone at a
normal voice level.
• The LED indicator lights red.
NOTE: Only one station is permitted to speak at a time.
eRelease [PTT] to return to receive.
• The LED lights green while receiving a signal.
rTo end the call, push [Moni (Audi)] to send a ‘Clear down’
signal.
• Either station can send a ‘Clear down’ signal.
• “CLR DOWN” is displayed for approximately 2 seconds.
• “ ” disappears, and the transceiver returns to the standby
mode.
DEmergency call
qWhen an emergency call is received:
• Beeps sound.
• “Emergency” and the calling station ID (or text) blink.
• The state of the backlight depends on the Backlight setting in the
User set mode. When “OFF Auto” is selected, the backlight turns
ON for the preprogrammed time period. (Auto Backlight Timer)
This function is usable in transceivers whose revision number is
3.0 or later. Ask your dealer for details.
Emergency
1111
Calling station ID
wThe transceiver automatically transmits an acknowledge-
ment to the calling station.
eTurn power OFF or change the channel to stop the beep
and display indication.

5
2BIIS 1200 OPERATION
DDisplaying the received call record
— Queue display
The transceiver memorizes the calling station ID in the
memory. Up to 3 calls can be memorized, and the oldest call
record is erased when a 4th call is received. However, once
the transceiver is powered OFF, all the records are erased.
qHold down [BIIS Button] for 1 second.
• The following display appears.
When a record is selectable
<QUEUE>
-QUEUE!-
When no record is stored
<QUEUE>
NO QUEUE
wPush [CH Up] or [CH Down] to select the desired call.
ePush and hold [BIIS Button] for 1 second again to return
to the standby mode.
• If no operation is performed for 30 seconds, the transceiver au-
tomatically returns to the standby mode.

6
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■Transmitting a call
There are 3 ways to select a call code— selecting from mem-
ory, calling back from the queue channel record, and entering
from the keypad.
DUsing call memory
qWhile in the standby mode, push [BIIS Button] to enter
the call code memory channel selection mode.
• “ ” appears.
1234
Appears
wPush [CH Up] or [CH Down] to select the desired call
code.
ePush [Call] or [PTT]* to call.
* A P TT call can be made only when PTT call capability is permit-
ted.
NOTE: When no answer back is received, the trans-
ceiver automatically repeats the call 3 times (default),
and “WAIT” is displayed during each call. However, an
error beep sounds and “FAILED” is displayed when
no answer back is received after the repeated calls.
rPush [PTT] to transmit; release to receive.
tPush [Moni (Audi)] to send a ‘Clear down’ signal.
DCalling back from the queue channel
q While in the standby mode , push and hold [BIIS Button] for
1 second to enter the queue memory channel selection
mode.
<QUEUE>
-QUEUE!-
wPush [Up] or [Down] to select the desired record.
0001
1234
ePush [Call] or [PTT]* to call.
* A PTT call can be made only when PTT call capability is permit-
ted.
NOTE: When no answer back is received, the trans-
ceiver automatically repeats the call 3 times (default),
and “WAIT” is displayed during each call. However, an
error beep sounds and “FAILED” is displayed when
no answer back is received after the repeated calls.
rPush [PTT] to transmit; release to receive.
tPush [Moni (Audi)] to send a ‘Clear down’ signal.

7
2BIIS 1200 OPERATION
DDirect code entry
qIn the standby mode, push [TX Code Enter] to enter the
TX code edit mode.
• A Code digit blinks.
1234
wPush [TX Code Enter] to select the desired digit to be
edited.
• Editable digits differ according to the transceiver setting.
ePush [CH Up] or [CH Down] to select the desired digit.
rPush [TX Code Enter] to set the digit, then the digit to the
right will automatically blink.
tRepeat eand rto edit all allowable digits.
yPush [Call] or [PTT]* to call.
* A PTT call can be made only when PTT call capability is permit-
ted.
NOTE: When no answer back is received, the trans-
ceiver automatically repeats the call 3 times (default),
and “WAIT” is displayed during each call. However, an
error beep sounds and “FAILED” is displayed when
no answer back is received after the repeated calls.
uPush [PTT] to transmit; release to receive.
iPush [Moni (Audi)] to send a ‘Clear down’ signal.
For your information
When the “UpDate” setting for the call code is enabled, the
set code is overwritten into the call code memory.

8
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■Receiving a message
DReceiving a status message
qWhen a status message is received:
• Beeps sound.
• The status message and the calling station ID (or text) is dis-
played when the display mode is 2 lines, as shown below.
• When the display mode is 1 line, the status message and the
calling station ID (or text) may be alternately displayed depend-
ing on the setting.
RX Status 01
1234
wPush [Moni (Audi)] to return to the standby mode.
NOTE: When the display mode is 1 line
Only the calling station ID (or text) is displayed (no message
is alternately displayed) when the scroll timer is set to ‘OFF.’
In this case, push [Status Up]/[Status Down] to manually
display the status message.
DReceiving an SDM (Short Data Message)
qWhen an SDM is received:
• Beeps sound.
• “ ” appears.
• The SDM and the calling station ID (or text) may be displayed
when the display mode is 2 lines, as shown below.
• The SDM and the calling station ID (or text) is alternately dis-
played when the display mode is 1 line, depending on the pre-
setting.
SDM8
1234
Appears
NOTE: When the received SDM includes more than 12
characters, the message automatically scrolls when the
automatic scroll function is activated.
• Push [Status Up]/[Status Down] to manually scroll the mes-
sage.
SDM12345678
1234
Appears
wPush [Moni (Audi)] to return to the standby mode.

9
2BIIS 1200 OPERATION
DSelecting a received message
The transceiver memorizes the received message in the
memory. Up to 6 messages for status and SDM, or 95 charac-
ter SDM’s can be memorized. The oldest message is erased
when the 7th message is received. However, once the trans-
ceiver is powered OFF, all messages are cleared.
qHold down [BIIS Button] for 1 second.
• The queue memory is displayed.
wPush [BIIS Button] again for 1 second.
• The message memory is displayed.
When a message is selectable
MESSAGE
-MSG!-
When no message is stored
MESSAGE
-NOMSG-
ePush [CH Up] or [CH Down] to select a desired mes-
sage.
• When selecting a SDM that includes more than 12 characters,
the message automatically scrolls when the automatic scroll
function is activated.
• Push [Status Up]/[Status Down] to manually scroll the mes-
sage.
rPush and hold [BIIS Button] for 1 second again to return
to the standby mode.
• If no operation is performed for 30 seconds, the transceiver au-
tomatically returns to the standby mode.

10
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■Transmitting a status
DGeneral
The programmed status message can be selected, and the
message text is also displayed on the function display of the
called station.
Up to 24 status types (1 to 24) are selectable, and status
messages 22 and 24 have designated meanings.
Status 22: Emergency*
Status 24: GPS request
* Status 22 can also be used as a normal status message by disa-
bling the designated meaning. However, the status 24 meaning
is fixed.
A status call can be sent with both individual and group
calls.
DTransmitting a status
qWhile in the standby mode, push [BIIS Button], then push
[CH Up] or [CH Down] to select the desired station/group
code.
wPush [BIIS Button] again, then push [CH Up] or
[CH Down] to select the desired status message.
STATUS 01
TX Status 01
Status message is displayed.
ePush [Call] or [PTT]* to transmit the status message to
the selected station or group.
* A PTT call can be made only when PTT call capability is permit-
ted.
• When the transmission is successful, 2 beeps sound and the
transceiver automatically returns to the standby mode.

11
2BIIS 1200 OPERATION
■Transmitting an SDM
DGeneral
The short data message, SDM, can be sent to an individual
station or group stations. Also, 8 SDM memory channels are
selectable and the messages can be edited on your PC.
DTransmitting an SDM
qWhile in the standby mode, push [BIIS Button], then push
[CH Up] or [CH Down] to select the desired station/group
code.
wPush [BIIS Button] again, then push [CH Up] or
[CH Down] to select the desired SDM.
• “ ” appears.
MESSAGE1
SDM1
SDM is displayed.
Appears
ePush [Call] or [PTT]* to transmit the SDM to the selected
station/group.
* A PTT call can be made only when PTT call capability is permit-
ted.
• 2 beeps sound and the transceiver automatically returns to the
standby mode when transmission is successful.
DDirect message input
The optional HM-152T is required for this operation.
qWhile in the standby mode, push [BIIS Button] twice, then
push [CH Up] or [CH Down] to select the desired SDM to
be edited.
• “ ” appears.
wPush [M]or [#] to enter the message editing mode.
• The first character blinks when [#] is pushed; the last character
blinks when [M]is pushed.
• “ ” blinks.
e Push the appropriate digit key, [0] to [9], to enter the de-
sired character.
• See the table on page 12 for the selectable characters.
• Pushing [CH Up] also enters a space, pushing [CH Down] de-
letes the selected character.
rPush [#] to move the cursor to the right, push [M]to move
the cursor to the left.
tRepeat steps eand rto enter the desired text mes-
sage.
yPush and hold [BIIS Button] for 1 second to write the set
message into the message memory.
• Push [BIIS Button] momentarily to cancel the editing and return
to the original message display.

12
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
• Selectable characters
Key
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
Characters
0 ! ? ' " , ; : _ ( ) < > [ ]
1 (space) # * / + - = & % $ @ ^
2 A B C a b c
3 D E F d e f
4 G H I g h i
5 J K L j k l
6 M N O m n o
7 P Q R S p q r s
8 T U V t u v
9 W X Y Z w x y z
/
!
■Position data transmission
When a GPS receiver is connected to the transceiver, the position
(longitude and latitude) data can be automatically transmitted.
Ask your dealer or system operator for connection details.
The position data is transmitted when:
• A status 24 message is received
* When the status 24 message, GPS request, is received.
• Automatic is enabled.
When automatic position transmission is enabled, sends
the position data according to ‘Time Marker’ and ‘Interval
Timer’ settings.
• PTT is released
When ‘Send with Logoff’ is enabled.
- Set the ‘Log-In/Off’ item as ‘L-OFF.’
• Send with Status is enabled
Sent after sending a status message.
• Send with SDM is enabled
Sent after sending an SDM.
• Send with Emergency is enabled
Sent after sending status 22 (Emergency).

13
2BIIS 1200 OPERATION
■Printer connection
When a printer is connected to the D-sub 25-pin connector on
the transceiver, the received SDM content and the called sta-
tion ID can be printed out. Ask your dealer or system operator
for connection details.
■BIIS ANI
Your own ID can be transmitted each time the PTT is pushed
(log-in) or released (log-off) with individual or group calls
communications.
When receiving an ANI, the communication log will be re-
corded when using a PC dispatch application.
In addition, when using the ANI with log-in, the PTT side tone
function can be used to inform you that the ID is sent and
voice communication can be made.
■Transmitting an Emergency call
When [Emergency] (described in the instruction manual) is
held down for the specified time period, an emergency signal
(Status 22) is transmitted once or repeatedly* on the emer-
gency channel. When no emergency channel is specified, the
signal is transmitted on the
operating channel.
* When the Repeat Cancel function is ON, the transceiver cancels
repeating after receiving an acknowledgement.
When the Repeat Cancel function is OFF, the transceiver repeats
calling according to the number of repeat cycles, even after receiv-
ing an acknowledgement.
This function is usable in transceivers whose revision number is 3.0
or later. Ask your dealer for details.
If you want to cancel the emergency call, hold down the key
again before transmitting the call.
The emergency call may be transmitted without a beep
sounding, and the LCD display, depending on the presetting.
(Silent operation)
The transceiver can also be programmed to keep the micro-
phone open during an emergency call, to allow monitoring of
the situation.
Ask your dealer for details.
IMPORTANT: Setting a separate emergency channel to
provide reliable emergency call operation is recom-
mended.

14
2
BIIS 1200 OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■Stun function
When the specified ID, set as a killer ID, is received, the stun
function is activated.
When a killer ID is received, the transceiver switches to the
password required condition. Entering the password with the
keypad is necessary to operate the transceiver again in this
case.
■BIIS indicators
The following indicators are available for the BIIS operation
on an MSK channel.
CONNECT : Individual/group calls are successful.
OK : Message (status or SDM) transmission was
successful.
FAILED : No answer back is received.
WAIT : Appears during retry of the call (2nd call).
CLR DOWN : End the call.
BUSY : The operating channel is busy.
■Priority A channel selection
When one of the following operations is performed, the trans-
ceiver automatically selects the Priority A channel.
Priority A is selected when:
• A clear down signal is received or transmitted
-
Set the ‘Clear down’ option as ‘Enable’ in ‘Move to PrioA
CH.’
• Turning the power ON
Priority A channel is selected each time the transceiver
power is turned ON.
• Status call
Priority A channel is selected when transmitting a status
call.
- Enable the ‘Send Status on PrioA CH’ item in the MSK
configuration.

15
2BIIS 1200 OPERATION
■Horn output
An automatic honking function can be used when a horn is
connected to D-Sub 25-pin connector on the transceiver.
When a status message is received, the transceiver sounds
the vehicle’s horn for a specified time period to announce a
status message has been received.
This is a convenient function when the operator is away from
the transceiver.
Ask your dealer or system operator, or refer to the service
manual for connection and setting details.

16
3
MDC 1200 SYSTEM OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■MDC 1200 system operation
The MDC 1200 signaling system enhances your transceiv-
er’s capabilities. It allows PTT ID, Selective Calling (SelCall),
Call Alert, Radio Check, Stun, Revive, Status, Messaging and
Emergency signaling.
An additional feature of the MDC 1200 system found in Icom
transceivers is called aliasing. Each transceiver on the system
has a unique ID number. Aliasing substitutes the ID number
with an alphanumeric name. For transmit, you can use this
alias to select a transceiver to call. For receive, the alias of
the calling station is displayed instead of the ID.
Please confirm that your dealer has set one of the program-
mable keys ([UP], [DOWN], [P0], [P1], [P2], [P3] or [P4]) for
MDC 1200 system operation.
NOTE: During MDC 1200 system operation, BIIS 1200
system and IDAS operations are disabled.
■Receiving a call
DReceiving a SelCall
qWhen a SelCall is received:
• Beeps sound.
• “ ” appears.
• “ ” blinks.
• The calling station ID (or alias) and “SELCALL” are alternately
displayed.
SELCALL
ID 1234
BlinksAppears
wHold down [PTT] and speak at your normal voice level.
eRelease [PTT] to receive.

DReceiving a Call Alert
qWhen a Call Alert is received:
• Beeps sound.
• “ ” blinks.
• The calling station ID (or alias) and “CALLALRT” are alternately
displayed
CALLALRT
ID 1234
Blinks
wHold down [PTT] and speak at your normal voice level.
eRelease [PTT] to receive.
DReceiving an Emergency Call
qWhen an emergency call is received:
• Beeps sound.
• The calling station ID (or alias) and “EMG EMG” are alternately
displayed.
• The action of the backlight depends on the Backlight setting in
the User set mode. When “OFF Auto” is selected, the backlight
turns ON for the specified time period*.
* If the Backlight Update setting is “Enable,” the preprogrammed
time period is enabled. (Auto Backlight Timer)
If the Backlight Update setting is “Inhibit,” the backlight does not
turn ON.
The Backlight Update and Auto Backlight Timer functions are
usable in transceivers whose revision number is 3.0 or later.
Ask your dealer for details.
ID 1234
EMGEMG
wWhen the Send Ack function is turned ON, the transceiver
automatically transmits an acknowledgement to the calling
station.
eTurn power OFF or change the channel to stop the beep
and display action.
17
3MDC 1200 SYSTEM OPERATION