ICP DAS USA ZT-2053 User manual

ZT-2053 - 14-channel DI Module with Counters- QuickStart (Sep/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 1
ZT-2053
ZigBee Wireless Module with 14 Digital Input
Channels
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/zt_2053
Introduction
The ZT-2053 offers 14 digital input channels which can be used for either dry or
wet contact. Its effective distance for dry contact is up to 500 meters. All channels
are able to be used as 16-bit counters. The ZT-2053 includes 14 LED indicators to
display the channel status as well as 4 kV ESD protection and 3750 Vrms intra-
module isolation. Users can easily to configure the module address, protocol,
checksum, ZB-PID and ZB-channel settings using a combination of rotary and DIP
switches.
1 What’s in the Shipping Package?
The shipping package contains the following items:
ZT‐2053 DIO Device ANT‐124‐05 Quick Start

ZT-2053 - 14-channel DI Module with Counters- QuickStart (Sep/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 2
2 Preparing the Device
1. Refer the chapter 3. to configure the DIP switch of ZT-2053 I/O device.
2. Install the ZT Configuration Utility to configure the ZT-2053 coordinator. CD:
\Napdos\ZigBee\ZT_Series\Utility http://ftp.icpdas.com/pub/cd/usbcd/napdos/zigbee/
zt_series/utility
3. Power Supply: +10 ~ +30 VDC
3 Setting up the ZT‐2053 DIO Device
3.1 Introduction to the Configuration Parameters
A. “Pan ID” parameter is the group identity for a ZigBee network, and must the same
for all devices in the same ZigBee network.
“Address/Node ID” parameter is the individed identity of a specific the ZigBee
module, and must be unique for each device connected the same ZigBee network.
B. “RF Channel” parameter indicates the radio frequency channel, and must be set to the
same value as other modules on the same ZigBee network.
Channel
0x00
0x01
……
0x0F
Frequency(MHz)
2405
2410
……
2480
※ RF channels 0x04, 0x09, 0x0E or 0x0F are recommended because they do not overlap
with the Wi-Fi frequencies based.
802.11b/g
802.11b/g
802.11b/g
Channel 1
Channel 6
Channel 11
2400 00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F 2485
MHz
MHz
802.11b/g Channel (North America)
802.15.4 Channel
C. Protocol/Application Mode：

ZT-2053 - 14-channel DI Module with Counters- QuickStart (Sep/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 3
When implementing custom programs based on different protocols, the following
application modes are recommended in order to ensure
communicatible
User Program Protocol
DCON
Modbus RTU
Modbus TCP
ZT-2053 I/O
ZT-2550
ZT-2570
DCON
Transparent
Transparent
Modbus RTU
Transparent
Transparent
Modbus Gateway
Modbus Gateway
Modbus RTU
------
Modbus Gateway

ZT-2053 - 8-channel DI DAQ module - QuickStart (Nov/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 4
4 Rotation Switch and DIP Switch
The configuration of ZT-2053 series can be adjusted by using the external rotary
switch and the DIP switches. The ZT-2053 device should only be rebooted once the
configuration is complete.
 DIP Switch to the ZT‐2042/ZT‐2043/ZT‐2053/ZT‐2055
Protocol Pan ID
ON
1
2
3
4
5
6
7
8
9
10
11
12
Checksum
RF Channel
Reserved
Address LSB
Address MSB
(Node ID)
(Node ID)
 DIP Switch to the ZT‐2053/ZT‐2060
Protocol Pan ID
Address LSB
Address MSB
Checksum
RF Channel
(Node ID)
(Node ID)

ZT-2053 - 8-channel DI DAQ module - QuickStart (Nov/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 5
 Rotation Switch
0
1
2
3
……
F
Note
Address
SW
01
02
03
……
0F
MSB = 0
Node ID
SW
0x0001
0x0002
0x003
……
0x000F
0
1
2
3
……
F
Address
10
11
12
13
……
1F
MSB = 1
Node ID
0x0010
0x0011
0x0012
0x013
……
0x001F
※ Once the address of hardware switch is set to 0x00, it mens the address is using software
configurations. Refer the more detailed information at Sec. 6.6 of user manual.
 DIP Switch
Number
Item
Status
Explain
1
Address MSB
OFF
Valid Address (Node ID) from 0x00 to 0x0F
ON
Valid Address (Node ID) from 0x10 to 0x1F
2
Protocol
OFF
DCON Protocol
ON
Modbus RTUProtocol
3
Checksum
OFF
Disabled
ON
Enabled
4
ZigBee Pan ID
OFF
Pan ID = 0x0000
ON
Pan ID = 0x0001
5
OFF
------
ON
0x08
6
OFF
------
ZigBee
ON
0x04
RF Channel
7
OFF
------
ON
0x02
8
OFF
------
ON
0x01

ZT-2053 - 8-channel DI DAQ module - QuickStart (Nov/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 6
5 Start‐up ZT‐2000 I/O Device
As the ZigBee network is controlled by the ZigBee coordinator, the ZT-2550/ZT-
2570 (ZigBee coordinator) must be configured first. Please refert to documents shown
below for full details of how to configure these devices.
Once configuration of the ZigBee coordinator has been completed. Set the ”Pan ID” and
the “RF Channel” values for the ZT-2000 I/O device to the same values as the network, and
then reboot the device. The module will automatically start to function on the ZigBee network
using the default protocol.
※Configuration Utility (Used to configure ZT-2000 I/O device Coordinator)
http://ftp.icpdas.com.tw/pub/cd/usbcd/napdos/zigbee/zt_series/utility/

ZT-2053 - 8-channel DI DAQ module - QuickStart (Nov/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 7
6 Examples
 Configurations of ZT‐2550/ZT‐2570
 Configurations of ZT-2000 I/O Device
12345678910 11 12
1
2
3
4
5
6
7
8
ON
Number
Item
Status
Explain
1
Address MSB
OFF
Address/Node ID is 01
(Rotation Switch=1)
2
Protocol
ON Use
Modbus RTU
Protocol
3
Checksum
OFF
Disabled
4
ZigBee Pan ID
OFF
Pan ID=0x0000
5
ON
0x08
6
ZigBee
ON
0x04
ZigBee RF Channel =
0x0E
7
RF
Channel
ON
0x02
8
OFF
------

ZT-2053 - 8-channel DI DAQ module - QuickStart (Nov/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 8
7 Communication Test
Once the ZT-2000 I/O device has joined the ZigBee network, the signal quality can
be comfirmed by monitoring the status of the ZigBee Net LED indicators. If the LED
indicator shows a steady light, communication with the ZT-2000 I/O device has been
successfully established for data acquisition and control.
ICP DAS also provides the “DCON Utility”, which can be used to simulate
DCON/Modbus communication. This software can also be used to verify the device
settings and ZigBee I/O functions.
※The DCON Utility can be dowmload from:
http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/
Simulate I/O channel operating via using DCON Utility
1. Launch DCON Utility and select the correct COM Port settings to connect the
ZigBee Coordinator (ZT-2550/ZT-2570).
2. Clicking “Search” button will start searching which ZT-2000 I/O device is in the
same ZigBee network.
3. If there is any ZT-2000 I/O devices displayed, double clicking the “module
name” will start the I/O channels operated platform.

ZT-2053 - 8-channel DI DAQ module - QuickStart (Nov/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 9

ZT-2053 - 8-channel DI DAQ module - QuickStart (Nov/2016)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 10
8 Troubleshooting
(1) Technical Support.
If you have any difficulties using your ZT-2000 series I/O device, please send a
description of the problem to [e-mail]
Include the following items in your email:
 A description or diagram of the current DIP switch positions.
 A copy of the configuration file for the ZT-2000 coordinator. This file can be
obtained using the procedure outlined below and should be attached to your email.
a. Set the DIP switch of the ZT-255x device to the [ZBSET] position then reboot the
device. Launch the ZT Configuration Utility and select [Save Log] icon to save the
configuration of the ZT-255x as a file.
b. After clicking the [Save Log] icon, enter the “File Name” and the “File Path” in
the Windows “Save” dialog box. Once the configuration has been successfully
saved, the following message will be displayed.