ICP DAS USA ISaGRAF WinCE ViewPAC User manual

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
1
ISaGRAF WinCE ViewPAC User Manual
[ Version: V.1.6 ]
ViewPAC Models:
VP-25W7 , VP-23W7 , VP-4137
VP-25W6 , VP-23W6 , VP-4136
** The ISaGRAF WinCE ViewPAC in this manual include: (abbreviation: VP-2xW7/4xx7 )
VP-25W7, VP-23W7, VP-4137 (Support ISaGRAF logic running in the PAC)
VP-25W6, VP-23W6, VP-4136 (Support InduSoft & ISaGRAF logic running in the same PAC)

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
2
ISaGRAF WinCE ViewPAC User Manual
Important Notice
1. Please store your application programs and data files in the \Micro_SD . Don't store them in the
\System_disk. That is because the \System_Disk is using Nor Flash memory. Its size is small and major
purpose is for storing OS, ISaGRAF driver, some basic utilities and DLL . The Nor Flash memory is not
good for frequently updating files. If update files frequently in the \System_Disk (for example, update
a file every 1 to 5 seconds, then it will be about ten thousand more updates in one day), the data or
files in the \System_disk may crush or lost for some days or months later.
2. ISaGRAF WinCE ViewPAC support only High profile I-8K and I-87K I/O cards in its slot 0 to 2. Please
refer to the accompanying CD-ROM: \napdos\isagraf\vp-25w7-23w7\english-manu\ Datasheet files.
3. Please always set a fixed IP address to the ISaGRAF WinCE ViewPAC. (No DHCP). Recommend to use the
NS-205/208 or RS-405/408 (Ring Switch) Industrial Ethernet Switch for them.
Legal Liability
ICP DAS CO., LTD. assumes no liability for any and all damages that may be incurred by the user as a
consequence of this product. ICP DAS CO., LTD. reserves the right to change this manual at any time
without notice.
ICP DAS CO., LTD. constantly strives to provide our customers with the most reliable and accurate
information possible regarding our products. However, ICP DAS CO., LTD. assumes no responsibility for its
use, or for any infringements of patents or other rights of third parties resulting from its use.
Trademark & Copyright Notice
The names of products and name of company are used for identification purposes only, and are the
registered trademarks of their respective owners or companies.
Development Software
Two options:
- ISaGRAF: Ver. 3.4x (or Ver. 3.5x), IEC61131-3 standard. LD, ST, FBD, SFC, IL & FC or
- Non-ISaGRAF: Microsoft EVC++4.0 or VS.NET 2008/2005/2003 (VB.net, C#.net)
Reference Guide
-  
VP-25W7/23W7 CD: \napdos\isagraf\vp-25w7-23w7\english-manu\
"user_manual_i_8xx7.pdf" and "user_manual_i_8xx7_appendix.pdf"
- ISaGRAF中文進階使用手冊:
VP-25W7/23W7 CD: \napdos\isagraf\vp-25w7-23w7\chinese-manu\

- More from the Internet:
www.icpdas.com > Product > Solutions > Soft PLC, ISaGRAF & Soft-GRAF HMI > ISaGRAF > Manual
Technical Service
[email protected].
FAQ : www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC
Writer: Chun Tsai, Last Editor: Eva Li
Copyright Jul. 2009, by ICP DAS CO., LTD. All Rights Reserved.

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
3
Table of Contents
ISaGRAF WinCE ViewPAC User Manual ......................................................................................................1
Important Notice........................................................................................................................................... 2
Legal Liability................................................................................................................................................. 2
Trademark & Copyright Notice ..................................................................................................................... 2
Development Software ................................................................................................................................. 2
Reference Guide............................................................................................................................................ 2
Technical Service........................................................................................................................................... 2
Table of Contents.......................................................................................................................................3
Reference Guide ........................................................................................................................................6
I/O Modules Selection Guide for ISaGRAF WinCE ViewPAC........................................................................7
Specifications: VP-25W7 / VP-23W7 / VP-4137 ........................................................................................11
Chapter 1 Typical Application ..........................................................................................................1-1
1.1 Soft-GRAF HMI Application: Colorful HMI..............................................................................1-1
1.2 eLogger HMI Application ........................................................................................................1-2
1.3 Redundant Communication System.......................................................................................1-3
1.4 New Hot-Swap and Redundant System .................................................................................1-3
1.5 Modbus Master: RTU, ASCII, RS-232/485/422.......................................................................1-4
1.6 Modbus Master: TCP/IP .........................................................................................................1-4
1.7 Modbus Slave: RTU/TCP .........................................................................................................1-5
1.8 Communicate With Other TCP/IP Server or UDP Client/Server Devices ...............................1-5
1.9 Multiple Web HMI Monitor & Control Everywhere!...........................................................1-6
1.10 Send Email with One Attached File ........................................................................................1-6
1.11 Data-Recorder & Data-Logger ................................................................................................1-7
1.12 Remote I/O Application..........................................................................................................1-7
1.13 SMS: Short Message Service...................................................................................................1-8
1.14 As a Modbus Gateway for the Remote I/O Modules.............................................................1-8
1.15 Motion Control .......................................................................................................................1-9
1.16 Stress Monitoring Application of Constructions ....................................................................1-9
1.17 Fast FRnet Remote I/O .........................................................................................................1-10
1.18 Integrate with CAN/CANopen Devices & Sensors................................................................1-10
1.19 VIP Communication Security ................................................................................................1-11
1.20 ISaGRAF PAC Connects the Smart Power Meter..................................................................1-11
1.21 ZigBee Wireless Solution ......................................................................................................1-12
1.22 GPS Application: ISaGRAF PAC Plus I-87211W or GPS-721..................................................1-13
1.23 Data Exchange: Ebus.............................................................................................................1-14
1.24 Detect Hot-Swap I-87K (High Profile) I/O Status..................................................................1-14
1.25 Database Application............................................................................................................1-15
1.26 HART Solutions .....................................................................................................................1-16
1.27 2G/3G Wireless Application .................................................................................................1-17
1.28 Measure humidity and temperature values via DL-100TM485 ...........................................1-18
Chapter 2 Software Installation And Working Soft-GRAF HMI with ISaGRAF....................................2-1
2.1 Step 1 - Installing The ISaGRAF Software ...............................................................................2-2
2.1.1 The Hardware Protection Device (Dongle & USB Key-Pro)....................................................2-3
2.1.2 Important Notice For Window 2000 Users ............................................................................2-4
2.1.3 Important Notice for Window NT Users ................................................................................2-4
2.1.4 Important Notice for Windows Vista or Windows 7 (32-bit) Users ..................................................2-5

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
4
2.1.5 Important Notice for Windows 7 (64-bit) Users ....................................................................2-7
2.1.6 Important Setting for Using Variable Arrays ..........................................................................2-7
2.2 Step 2 - Installing The ICP DAS Utilities For ISaGRAF..............................................................2-8
2.3 Step 3 - Installing The Web Page Editor .................................................................................2-9
2.4 Working eLogger HMI with ISaGRAF SoftLogic ......................................................................2-9
2.5 Working Soft-GRAF HMI with ISaGRAF SoftLogic.................................................................2-10
Chapter 3 Setting Up A Web HMI Demo...........................................................................................3-1
3.1 Web Demo List .......................................................................................................................3-1
3.2 Steps To Set Up A Web HMI Demo ........................................................................................3-2
3.2.1 Step 1 Set up The Hardware................................................................................................3-2
3.2.2 Step 2 - Setting The Web Options ..........................................................................................3-2
3.2.3 Step 3 - Download ISaGRAF Project .......................................................................................3-3
3.2.4 Step 4 - Download Web Pages To The ViewPAC ....................................................................3-6
3.2.5 Step 5 - Show Time .................................................................................................................3-6
Chapter 4 Programming A Web HMI Example..................................................................................4-1
4.1 Writing A Simple ISaGRAF Program........................................................................................4-2
4.1.1 Open ISaGRAF-Project Management .....................................................................................4-3
4.1.2 .........................................................................................4-3
4.1.3 Creating A New ISaGRAF Project............................................................................................4-4
4.1.4 Declaring The ISaGRAF Project Variables ...............................................................................4-5
4.1.5 Assign Modbus Network Address No to Variables.................................................................4-8
4.1.6 Create The LD - "LD1" Program ............................................................................................4-10
4.1.7 Edit The "LD1" Program........................................................................................................4-11
4.1.8 Connecting The I/O...............................................................................................................4-14
4.2 Compiling & Simulating The Example Project ......................................................................4-16
4.3 Download & Debug The Example Project ............................................................................4-20
4.4 Design The Web Page...........................................................................................................4-24
4.4.1 Step 1 Copy The Sample Web HMI pages .........................................................................4-24
4.4.2 Step 2 Building The Main.htm ...........................................................................................4-25
4.4.3 Step 3 Adding Control Code To The Main.htm..................................................................4-30
4.4.4 Step 4 Download Web HMI Pages To The Controller........................................................4-37
Chapter 5 Web HMI Basics...............................................................................................................5-1
5.1 Basic Files For The Web HMI ..................................................................................................5-1
5.2 Login.htm................................................................................................................................5-2
5.3 menu.htm ...............................................................................................................................5-4
5.4 main.htm ................................................................................................................................5-6
5.4.1 A Simple Main.htm Example ..................................................................................................5-6
5.4.2 More About The refresh_data( ) Function And Dynamic Data ..............................................5-8
5.4.3 Post Data To The Controller .................................................................................................5-13
5.5 Multi-Pages...........................................................................................................................5-17
5.5.1 Level 2 And Level 3 Page ......................................................................................................5-17
5.5.2 Switch One Page To One Another Page ...............................................................................5-18
5.6 Web Security ........................................................................................................................5-19
Chapter 6 VB.NET 2008 Program Access To ISaGRAF Variables ........................................................6-1
6.1 Create a New Project..............................................................................................................6-1
6.2 Add Project Reference for an Application..............................................................................6-3
6.3 Compiling an Application Program.........................................................................................6-5
6.4 QuickerNET.DLL ......................................................................................................................6-6
6.4.1 Digital R/W Functions.............................................................................................................6-6

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
5
6.4.2 Analog R/W Functions ............................................................................................................6-8
Chapter 7 EVC++ Program Access To ISaGRAF Variables...................................................................7-1
Chapter 8 InduSoft Project Access To ISaGRAF Variables .................................................................8-1
Chapter 9 Example Program & FAQ..................................................................................................9-1
9.1 Get On-Line help.....................................................................................................................9-1
9.2 Installing The ISaGRAF Programming Examples.....................................................................9-4
9.3 Frequently Asked Questions.................................................................................................9-11
Chapter 10 C# .NET 2008 Program Access To ISaGRAF Variables ......................................................10-1
10.1 Create a New Project............................................................................................................10-1
10.2 Add Project Reference for an Application............................................................................10-3
10.3 Compiling an Application Program.......................................................................................10-5
10.4 QuickerNET.DLL ....................................................................................................................10-5
10.4.1 Digital R/W Functions...........................................................................................................10-6
10.4.2 Analog R/W Functions ..........................................................................................................10-7
Chapter 11 More Useful Features ....................................................................................................11-1
11.1 FAQ-167: Develop Your Own C-function and C-function Blocks in the ISaGRAF WinCE PAC
..............................................................................................................................................11-1
11.2 FAQ-166: ISaGRAF WinCE PAC - Schedule Control...............................................................11-2
11.3 FAQ-160: Soft-GRAF Application - Alarm Lists .....................................................................11-3
11.4 FAQ-158: Soft-GRAF Application - Data Logger....................................................................11-4
Appendix A Hardware System & Setting ................................................................................................1
A.1 Applying Correct Power Supply................................................................................................. 1
A.2 Modify The NET-ID & Modbus RTU Port Setting....................................................................... 3
A.3 Setting The IP Address For The ViewPAC .................................................................................. 4
A.4 Connecting Your PC To The ViewPAC Ethernet Port................................................................. 5
A.5 Pin Assignment of COM2 , COM3 and Multi-Clients................................................................. 6
A.6 Connecting PC To VP-2xW7 's COM2 or COM3......................................................................... 7
A.7 Deleting the ISaGRAF Project From The ViewPAC .................................................................... 8
A.8 Linking I-7000 and I-87K Modules For Remote I/O................................................................... 9
A.9 Linking To An HMI Interface Device .......................................................................................... 9
A.10 Linking To Other Modbus Devices........................................................................................... 10
A.11 Recalibrate The Touch Screen Of VP-25W7 ............................................................................ 11
Appendix B Upgrade ISaGRAF Driver to Newer Version.......................................................................13
Appendix C Hardware Interface & Dimension......................................................................................16
Appendix D Enable The Second Ethernet Port Of The VP-2xW7/2xW6/4137/4136 ..............................21
Appendix E Using Expansion RS-232/485/422 .....................................................................................23
Appendix F ..................................................................................26
Appendix G Setup More Modbus RTU Salve Ports................................................................................27
Appendix H Compiling Error Result In Different ISaGRAF Version ........................................................28
Appendix I Why my PC running ISaGRAF cannot connect the ISaGRAF PAC correctly ?.......................29
Appendix J Control Buttons On the Front Panel..................................................................................30
Appendix K Enable the Screen Saver of ViewPAC.................................................................................31
Appendix L How to Detect the Status of Dual Battery and the Ethernet Port ...........................................32

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
6
Reference Guide
 
ISaGRAF WinCE ViewPAC CD: \napdos\isagraf\vp-25w7-23w7\english-manu\
"user_manual_i_8xx7.pdf" and "user_manual_i_8xx7_appendix.pdf"
ISaGRAF 中文進階使用手冊:
ISaGRAF WinCE ViewPAC CD: \napdos\isagraf\vp-25w7-23w7\chinese-manu\
"chinese_user_manual_i_8xx7.pdf" and "chinese_user_manual_i_8xx7_appendix.pdf"
Web: www.icpdas.com > Product > Solutions > Soft PLC, ISaGRAF & Soft-GRAF HMI > ISaGRAF > Manual
Industrial Ethernet Switch : NS-205/208 or RS-405/408 (Ring Switch)
www.icpdas.com > Product > Solutions > Industrial Ethernet Switch & Fber Switch > Unmanaged
Ethernet Switches
Power Supply :
www.icpdas.com > Product > Solutions > Accessories > Power Supply
DP-660 : 24 V / 2.5 A , 5 V / 0.5 A power supply (DIN-Rail mounting)
DP-665 : 24 V / 2.5 A , 5 V / 0.5 A power supply
DP-1200 : 24 V / 5 A power supply
FAQ:
www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC
Model: DP-665
Model: RS-405
Model: RS-408
Model: NS-205
Model: NS-208

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
7
I/O Modules Selection Guide for ISaGRAF WinCE ViewPAC
ISaGRAF WinCE ViewPAC support only the I-8K / I-87K High Profile I/O modules and RS-485 / FRnet remote
I/O modules listed in the ISaGRAF Data Sheet . Please refer to the list in the next page or follow the below
steps to get the newest list.
1. www.icpdas.com
2. Click here to go to the ISaGRAF page
3. Data Sheet

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
8
High Speed Local I/O Modules: Parallel Bus
I-8K High Profile Modules: More at www.icpdas.com > Product > Solutions > Remote I/O Modules/Units > I-8K & 87K
I-8K Analog I/O Modules
I-8014W
16-bit 250K sampling rate 8/16-ch. analog input module (The scan rate cannot reach 250K when using in
the ISaGRAF PAC)
I-8017HW
8-ch. Differential or 16-ch. Single-ended, 14-bit, High Speed Analog Input Module. (current input require
external 125 resistor) (The scan rate cannot reach 100K when using in the ISaGRAF PAC)
I-8024W
4-ch. Isolated Analog Output Module (+/-10 V, 0 ~ +20 mA)
I-8K Digital I/O Modules
I-8037W
16-ch. Isolated Open Collector Output Module
I-8040W
32-ch. Isolated Digital Input Module
I-8040PW
32-ch. Isolated Digital Input with Low Pass Filter Module
I-8041W
32-ch. Isolated Open Collector Digital Output Module (Sink)
I-8041AW
32-ch. Isolated Open Collector Digital Output Module (Source)
I-8042W
16-ch. Isolated Digital Input & 16-ch. Isolated Open Collector Digital Output Module
I-8046W
16-ch. Isolated Digital Input Module
I-8050W
16-ch. Universal Digital I/O Module
I-8051W
16-ch. Non-isolated Digital Input Module
I-8052W
8-ch. Differential Isolated Digital Input Module
I-8053W
16-ch. Isolated Digital Input Module
I-8053PW
16-ch. Isolated Digital Input with Low Pass Filter Module
I-8054W
8-ch. Isolated Digital Input Module & 8-ch. Isolated Open Collector Digital Output Module
I-8055W
Non-isolated 8-ch. Digital Logic Input Module & 8-ch. Open Collector Digital Output Module
I-8056W
16-ch. Non-isolated Open Collector Output Module
I-8057W
16-ch. Isolated Open Collector Output Module
I-8058W
8-ch. Differential Isolated Digital Input Module, Max. AC/DC Input : 250V
I-8060W
6-ch. Relay Output Module, AC: 0.6 A @ 125 V , 0.3 A @ 250 V; DC: 2 A @ 30 V
I-8063W
4-ch. Differential Isolated digital input & 4-ch. Relay output module, AC : 0.6 A @ 125 V ; 0.3 A @ 250 V
I-8064W
8-ch. Power Relay Output Module, AC: 5 A @ 250 V, DC: 5 A @ 30 V
I-8068W
4-ch. Form-A, 5 A @ 250 VAC /28 VDC & 4-ch. Form-C, 5 A (NO) /3 A (NC) @ 277 VAC /30 VDC Relay Output
Module
I-8069W
8-ch. PhotoMOS Relay Output Module, Max. AC/DC: 1 A @ 60 V
I-8K Counter/Frequency Modules
I-8084W
4-ch. Encoder, can be dir/pulse, or up/down or A/B phase (Quad. mode), Not support Encoder Z-index
I-8088W
8-ch. PWM Output and 8-ch. isolated DI Module, software support 1 Hz ~ 100 kHz (non-continuous).
I-8K Motion Modules
I-8093W
3-axis Encoder Module, max. 1M Hz for quadrant input mode, max. 4M Hz for pulse/direction and cw/ccw
input model
I-8090W
3-axis Encoder Module
I-8091W
2-axis Stepping/Servo Motor Control Card without encoder input
I-8092F
High Speed 2-axis Motion Control Module, with FRnet Master (For XP-8xx7-CE6 only)
I-8094
High Speed 4-axis Motion Control Module (For XP-8xx7-CE6 only)
I-8094F
High Speed 4-axis Motion Control Module, with FRnet Master (For XP-8xx7-CE6 only)
I-8K Communication Modules
I-8112iW
2-ch. Isolated RS-232 Expansion Module
I-8114W
4-ch. non-isolated RS-232 Expansion Module
I-8114iW
4-ch. Isolated RS-232 Expansion Module
I-8142iW
2-ch. Isolated RS-422/485 Expansion Module
I-8144iW
4-ch. Isolated RS-422/485 Expansion Module

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
9
I-8172W
2-port FRnet Module
I-8K CAN Bus Modules
I-8123W
1 Port High Performance CANopen Master Module
RS-485 Remote I/O Modules: Serial Interface; HOT-SWAP
I-87K High Profile Modules: More at www.icpdas.com > Product > Solutions > Remote I/O Modules/Units > I-8K & 87K
I-87K Analog I/O Modules
I-87005W
8-ch. Thermistor input and 8-ch. digital output module
I-87013W
4-ch., 16-bit, 10 Hz (Total), 2/3/4 Wire RTD Input Module with Open Wire Detection
I-87015W
7-ch., 16-bit, 12 Hz (Total), RTD Input Module with Open Wire Detection (for short sensor distance)
I-87015PW
7-ch. RTD Input Module with 3-wire RTD lead resistance elimination and with Open Wire Detection (for
long sensor distance)
I-87017RW
8-ch. Differential , 16/12-bit, 10/60 Hz (Total) Analog Input Module with 240 Vrms Over Voltage Protection,
Range of -20 ~ +20 mA 
I-87017RCW
8-ch. Differential , 16/12-bit, 10/60 Hz(Total) Current Input Module
I-87017W
8-ch. Analog Input Module
I-87017W-A5
8-ch. High Voltage Input Module
I-87017DW
8-ch. Analog Input Module (Gray Cover) (RoHS)
I-87017ZW
10/20-ch. Analog Input Module with High Voltage Protection (RoHS)
I-87018PW
8-ch. Thermocouple Input Module (Gray Cover) (RoHS)
I-87018RW
8-ch. Thermocouple Input Module. Recommend to use the better I-87018Z.
I-87018W
8-ch. Thermocouple Input Module. Recommend to use the better I-87018Z.
I-87018ZW
10-ch. Differential , 16-bit, 10 Hz (Total), Thermocouple Input Module with 240 Vrms Over Voltage
Protection, Open Wire Detection, Range of +/-20 mA, 0~20 mA, 4~20 mA requires Optional External 125 
Resistor
I-87019PW
8-ch. Universal Analog Input Module (RoHS) (With a CN-1824 Daughter Board)
I-87019RW
8-ch. Diff. , 16-bit, 8 Hz (Total), Universal Analog Input Module with 240 Vrms Over Voltage Protection,
Open Wire Detection (V, mA, Thermocouple; Range of -20 ~ +20 mA need to set Jumper on board)
I-87019ZW
10-ch. Universal Analog Input Module (Gray Cover) (RoHS), Includes the I-87019ZW Module and a DB-1820
Daughter Board
I-87024CW
4-ch. 12-bit channel to channel isolated current output module with open-wire detection
I-87024DW
4-ch. 14-bit analog output module
I-87024RW
4-ch. 14-bit analog output module
I-87024W
4-ch. 14-bit analog output module (0 ~ +5 V, +/-5 V, 0 ~ +10 V, +/-10 V, 0 ~ +20 mA, +4 ~ +20 mA)
I-87028CW
8-ch. 12-bit current output module
I-87H17W
8-ch. analog input module and HART master module.
I-87K Multifunction I/O Modules
I-87026PW
6-ch. Analog Input, 2-ch. Analog Output, 2-ch. Digital Input and 2-ch. Digital Output Module (RoHS)
I-87K Digital I/O Modules
I-87037W
16-ch. source type Isolated Digital Output Module(RoHS)
I-87040W
32-ch. Isolated Digital Input Module
I-87040PW
32-ch. Isolated Digital Input Module with 16-bit Counters (RoHS)
I-87041W
32-ch. Sink Type Open Collector Isolated Digital Output Module
I-87046W
16-ch. Non-Isolated Digital Input Module for Long Distance Measurement
I-87051W
16-ch. Non-Isolated Digital Input Module
I-87052W
8-ch. Differential , Isolated Digital Input Module
I-87053PW
16-ch. Isolated Digital Input Module with 16-bit Counters
I-87053W
16-ch. Isolated Digital Input Module
I-87053W-A5
16-ch. 68 ~ 150 VDC Isolated Digital Input Module
I-87053W-AC1
16-ch. AC Isolated Digital Input Module with 16-bit Counters
I-87053W-E5
16-channel 68-150 VDC solated Digital Input Module with 16-bit Counters
I-87054W
Isolated 8-ch. DI and 8-ch. Open Collector DO Module
I-87055W
Non-Isolated 8-ch. DI and 8-ch. Open Collector DO Module

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
10
I-87057W
16-ch. Open Collector Isolated Digital Output Module
I-87057PW
16-ch. Open Collector Isolated Digital Output Module
I-87058W
8-ch. 80~250 VAC Isolated Digital Input Module
I-87059W
8-ch. Differential 10-80 VAC Isolated Digital Input Module
I-87061W
16-ch. Relay Output Module (RoHS)
I-87063W
4-ch. Differential Isolated Digital Input and 4-ch. Relay Output Module 5 A (NO) / 3 A(NC) @ 5 ~ 24 VDC ; 5
A(NO) / 3 A(NC) @ 0 ~ 250 VAC
I-87064W
8-ch. Relay Output Module, 5 A (47~63 Hz) @ 0~ 250 VAC ; 5 A @ 0~ 30 VDC
I-87065W
8-ch. AC SSR Output Module, AC: 1.0 Arms @ 24 ~ 265 Vrms
I-87066W
8-ch. DC SSR Output Module , DC: 1.0 Arms @ 3 ~ 30 VDC
I-87068W
4-ch. Form-A Relay Output and 4-ch. Form-C Relay Output Module ; Form-A: 8 A @ 250 VAC; 8 A @ 28
VDC; Form-C: 5 A (NO) / 3 A (NC) @ 277 VAC ; 5 A(NO ) / 3 A(NC) @ 30 VAC
I-87069W
8-ch. PhotoMOS Relay Output Module, Max. AC/DC: 0.13 A @ 350 V
I-87K Counter/Frequency Modules
I-87082W
2-ch. Counter/Frequency Module, Isolated or Non-isolated Inputs
I-87K PWMS Modules
I-87088W
8-ch. PWM outputs, software support 1 Hz~100 kHz, (non-continuous), duty: 0.1 ~ 99.9%
I-87K GPS Modules
I-87211W
Time-Synchronization and GPS module for getting UTC/local time and local Longitude/Latitude
RS-485 Remote I/O Modules
I-7000
DCON Protocol
www.icpdas.com > product > solutions > remote i/o modules/units > I-7000 & M-7000
M-7000
Modbus RTU and DCON Protocol
www.icpdas.com > product > solutions > remote i/o modules/units > I-7000 & M-7000
tM-7000
DCON, Modbus RTU, Modbus ASCII
Protocol
www.icpdas.com > product > solutions > remote i/o modules/units > tm-series
RS-485 Remote I/O Expansion Unit
RU-87P1/2/4/8
Hot-Swap, Auto-Config.
www.icpdas.com > product > solutions > pac > I/O Expansion Unit
I-87K1/4/5/8/9
www.icpdas.com > product >solutions > pac > I/O Expansion Unit
Ethernet I/O Modules
ET-7000
Web based
www.icpdas.com > product > solutions > Remote I/O > Ethernet I/O
PET-7000
PoE Web based
www.icpdas.com > product > solutions > Remote I/O > Ethernet I/O
tPET/tET-7000
Modbus TCP based (PoE)
http://www.icpdas.com/products/Remote_IO/petl-7000/PETL_Series_Main_Page.htm
Ethernet I/O Expansion Unit
I-8KE4/8-MTCP
Modbus/TCP based
www.icpdas.com > product > solutions > pac > iPAC-8000 > I-8KE4-MTCP-G/I-8KE8-MTCP-G

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
11
Specifications: VP-25W7 / VP-23W7 / VP-4137
Specification:
Models
VP-23W7
VP-25W7
VP-4137
System Software
OS
Windows CE 5.0
.Net Compact
Framework
3.5
Embedded Service
FTP server, Web server (supports VB script, JAVA script), Embedded SQL server
SDK Provided
Dll for eVC, Dll for Visual Studio.Net 2005/2008
Multilanguage
Support
English, German, French, Spanish, Russian, Italian, Korean, Simplified Chinese, Traditional
Chinese
Development Software
ISaGRAF Software
ISaGRAF Ver.3
IEC 61131-3 standard
Languages
LD, ST, FBD, SFC, IL & FC;
Support Soft-GRAF HMI: XP-8xx7-CE6/8xx7-Atom-CE6, WP-8xx7/5xx7 and VP-2xW7/4xx7
PAC
Max. Code Size
1 MB
Scan Time
3 ~ 15 ms for normal program
15 ~ 50 ms (or more)for complex or large program
Non-ISaGRAF
Options: MS eVC++ 4.0 or VS .NET 2005/2008 (VB.NET, C# .NET)
Web Service
Web HMI
PC running Internet Explorer can monitor/control PAC via Internet/modem
Security
Support three-level username and password protection. (high/middle/low)
CPU Module
CPU
PXA270, 520 MHz
SDRAM
128 MB
Flash
96 MB
128 MB
Expansion Flash
Memory
microSD socket with one microSD card (support up to 32 GB)
Dual Battery Backup
SRAM
512 KB; data valid up to 5 years (for retain variables)
EEPROM
16 KB
RTC (Real Time
Clock)
Provide second, minute, hour, date, day of week, month, year
64-bit Hardware
Serial Number
Yes, for Software Copy Protection
Dual Watchdog
Timers
Yes (0.8 second)
Rotary Switch
Yes (0 ~ 9)
Communication Interface
Ethernet
RJ-45 x 1
10/100 Base-TX (Auto-negotiating, LED indicators)
USB 1.1 (host)
1
2
USB 1.1 (client)
-
1
COM 0
Internal communication with the high profile I-87K series modules in slots
COM 1
-

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
12
COM 2
RS-485 (Data+, Data-) with internal self-tuner ASIC; 2500 VDC isolated
COM 3
RS-232 (RxD, TxD, CTS, RTS, DSR, DTR, CD, RI and GND); Non-isolated
MMI (Man Machine Interface)
LCD

(Resolution 320 x 240)

(Resolution 640 x 480)

(Resolution 800 x 600)
Touch Panel
-
Yes
Rubber Keypad
24 keys
6 Keys
-
Audio
Microphone-In and Earphone-Out
Earphone-Out
LED Indicators
3 Dual-Color LEDs
(PWR, RUN, LAN1, L1, L2, L3; L1 ~ L3 for User Programmable)
2 LEDs (PWR, RUN)
I/O Expansion Slots
Slot Number
3
Note: For High Profile I-8K and I-87K Modules Only
Mechanical
Dimensions
(W x L x H)
182 mm x 158 mm x 125 mm
293 mm x 231 mm x 129 mm
Installation
Panel Mounting
Ingress Protection
Front panel: IP65
Environmental
Operating
Temperature
-20 ~ +70°C
Storage
Temperature
-30 ~ +80°C
Ambient Relative
Humidity
10 ~ 90% RH (non-condensing)
Power
Input Range
+10 ~ +30 VDC
Isolation
1 kV
Capacity
12.5 W
Consumption
7.2 W
8.5 W
Protocols (Note that certain protocols require optional devices)
NET ID
1 ~ 255, user-assigned by software
Modbus TCP/IP
Master
Link to a max. of 100 devices that support the Standard Modbus TCP/IP Slave protocol
(FAQ-113)
Modbus RTU/ASCII
Master
A max. of 10 ports: COM2, 3 and COM5 ~ 14. (To connect to other Modbus Slave devices.)
Support Multi-port. (*)
Modbus RTU Slave
A max. of 5 ports: one of COM2/3, COM5 ~ 8. (For connecting ISaGRAF, PC/HMI/OPC Server
and HMI panels.) (*)
Modbus TCP/IP
Slave
LAN1 and optional 2nd Ethernet Port in I-8135W support total up to 32 connections for
connecting ISaGRAF and PC/HMI. If one of the Ethernet port malfunctions, the other one
can still be used to connect to the PC/HMI.
Web HMI Protocol
Ethernet ports for connecting a PC running Internet Explorer.
User-defined
Protocol
Custom protocols can be applied at COM2~3 and COM5~14 using Serial communication
function blocks. (*)
I-7000 & I-87K
RS-485 Remote I/O
One of COM2 or COM3 supports I-7000 I/O modules, I-87K base + I-87K Serial I/O boards,
or RU-87Pn + I-87K High Profile I/O boards as remote I/O. A max. of 255 I-7000/87K remote
I/O modules can connect to one PAC. (*)

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
13
M-7000 Series
Modbus I/O
A max. of 10 RS-485 ports: COM2, 3, 5 ~ 14. Each port can connect to up to 32 M-7000
modules. (With optional I-7510 repeater connected can connect to up to more than 32
M-7000 Modules) (*)
Modbus TCP/IP I/O
Supports ICP DAS Ethernet I/O : I-8KE4-MTCP and I-8KE8-MTCP. If LAN1 malfunctions, it will
automatically switch to the 2nd Ethernet port (in optional I-8135W card) to continuously
work. (The IP address for LAN1 and the 2nd Ethernet's IP should be set in the same IP
domain) (FAQ-042)
FRnet I/O
Enable a max. of 3 pcs. I-8172W boards in slot 0~2 to be used to connect to FRnet I/O
modules, such as FR-2053, FR-2057, FR-32R, FR-32P. Each I-8172W board can link to a
max. of 256 DI plus 256 DO channels. (FAQ-082, 154)
Send Email
Provide functions to send email with a single attached file via the Ethernet port.
Ebus
Used to exchange data between ICP DAS ISaGRAF Ethernet PACs via the Ethernet port.
(LAN1 Port only)
SMS: Short Message
Service
Either COM3 or COM5 can link to a GSM Modem to support SMS. The user can request
data/control the controller via a cellular phone. The controller can also send data and

Optional GSM Modem: GTM-201-RS232 (850/900/1800/1900 GSM/GPRS External Modem)
MMICON/LCD
COM3 or COM5 supports the ICP DAS MMICON. (*) The MMICON is featured with a 240 x
64 dot LCD & a 4 x 4 Keyboard to display picture, string, integer, float, & input a char, string,
integer & float.
UDP Server & UDP
Client :
Exchange Message
& Auto-report
LAN1 or the 2nd Ethernet (in optional I-8135W card) supports the UDP Server and UDP
Client protocols allowing messages to be sent/received to/from a PC/HMI or other device.

TCP Client :
Exchange Message
& Auto-report
LAN1 or the 2nd Ethernet (in optional I-8135W card) supports the TCP Client protocol
allowing messages to be sent/received to/from a PC/HMI or other device that supports the
TCP server protocol. For example, data       
RXTX driver, or to connect a location camera.
GPRS/SMS
Enable the I-8212W (2G/3G) card allowing short messages to be sent/received to/from or
to access a dial up connection to link to the Internet and using a GPRS connection to send
an email or communicate with remote stations using the "FTP Client" (FAQ-151) or the
"TCP Client"/"UDP Server"/"UDP Client" (FAQ-143) protocols.
SQL Client
Support for the SQL Client function that allows data to be written (or read from) a
Microsoft SQL Server (2000 SP3, 2005, 2008).
Hot-Swap and
Redundant System
Must enable the 2nd Ethernet port in the optional I-8135W card. This redundant system has
-2xW7/2xW6 's LAN1 and 2nd Ethernet
ports always. One or two or more PC / HMI / SCADA can communicate with this redundant
system via one of the two given active IP. So the PC / HMI / SCADA can access to the system
easily without any notice about which VP-2xW7/2xW6 is currently active. Moreover, the
new redundant system can integrate with the RU-87P4 and RU-87P8 expansion unit plus
the I-87K high-profile I/O cards to support the hot-swap application. If the I/O card is
damaged, the maintenance person just takes one good-card with same model number to
hot-swap the damaged one without stopping this redundant system. (FAQ-093)
CAN/CANopen
COM3 or COM5~14 can connect to one I-7530 (converter: RS-232 to CAN) to support
CAN/CANopen devices and sensors. One PAC supports a max. of 10 RS-232 ports to
connect a max. of 10 I-7530. (*) (FAQ-086)
CANopen Master
Enable the I-8123W CANopen Master card to connect to other CANopen Slave devices.
(FAQ-145)
HART Solutions
Enable I-87H17W modules in slots 0 to 2 to communicate with other HART devices.
FTP Client
Enable the FTP Client to upload files from the PAC to a remote FTP server on a PC.
(FAQ-151)
The Soft-GRAF g_Alarm and g_Logger1 HMI objects also support FTP Client. (FAQ-146)

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
14
Soft-GRAF HMI
Provide support for the Soft-GRAF HMI. The user can design the HMI screen using the
Soft-GRAF Studio on the PC and then download it to the PAC to display the HMI on the PAC.
(FAQ-146)
Optional I/O Functions (Refer to the ISaGRAF PAC I/O Selection Guide for I/O Module list)
PWM
Output
High Speed
PWM
Module
I-7088, I-8088W, I-87088W: 8-ch. PWM outputs, software support 1 Hz~100 kHz
(non-continuous), duty: 0.1~99.9%
DO
Module as
PWM
8-ch. max. 250 Hz max. For Off=2 & On=2 ms. Output square curve: Off: 2 ~ 32766 ms, On: 2
~ 32766 ms.
Optional DO Boards: I-8037W, 8041W, 8041AW, 8042W, 8050W, 8054W, 8055W, 8056W,
8057W, 8060W, 8063W, 8064W, 8068W, 8069W. (Relay Output boards cannot generate
fast square wave)
Counter,
Encoder, Frequency
Parallel DI
Counter
8-ch. max. For 1 controller. Counter val: 32-bit. 250 Hz max. Min. ON & OFF width must > 2
ms.
Optional DI boards: I-8040W, 8040PW, 8042W, 8046W, 8048W, 8050W, 8051W, 8052W,
8053W, 8053PW, 8054W, 8055W, 8058W, 8063W.
Serial DI
Counter
Counter input: 100 Hz max. Counter value: 0 ~ 65535 (16-bit)
Optional serial I-87K DI boards: I-87040W, 87046W, 87051W, 87052W, 87053W,
87053W-A5, 87054W, 87055W, 87058W, 87059W, 87063W.
Remote DI
Counter
All remote I-7K/I-87K DI modules support counters. 100 Hz max. Value: 0 ~ 65535
High Speed
Counter
I-87082W: 100 kHz max., 32-bit; I-8084W: 250 kHz max., 32-bit
Encoder
I-8093W: 3-axis Encoder Module, max. 1M Hz for quadrant input mode, max. 4 MHz for
pulse/direction and cw/ccw input mode. (FAQ-112)
I-8084W: 250 kHz max., 4-ch encoder, pulse/direction or up/down or A/B phase (Quad.
mode), Not support Encoder Z-index. (FAQ-100)
Frequency
I-87082W: 2-ch, 1 Hz ~ 100 kHz; I-87088W: 8-ch, 0.1 Hz ~ 500 kHz; I-8084W: 8-ch, 1 Hz ~
250 kHz;
Motion
Motion
Control
one I-8091W (2-axis) or two I-8091W (4-axis) can do motion control. only one I-8091W can
do X-Y dependent motion.
Port
Second
Ethernet
VP-2xW7/2xW6/4137 can add one optional I-8135W card in its slot 0 ~ 2 to expand the
second Ethernet port.
* Note: The COM5 ~ COM14 ports are located in the expansion boards if they are installed in slots 0~2 of
VP-2xW7/4xx7.
* ISaGRAF FAQ: www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC
*ICP DAS recommends using NS-205/NS-208 or RS-405/408 (Ring Switch) Industrial Ethernet Switches.

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
1-1
Chapter 1 Typical Application
The website for the applications supporting list of all ISaGRAF PACs : www.icpdas.com > Product >
Solutions > Soft PLC, ISaGRAF & Soft-GRAF HMI > ISaGRAF > Applications
1.1 Soft-GRAF HMI Application: Colorful HMI
Support Various and Colorful HMI Objects:
Pages (Max. 200, Support Password Security)
Label (Normal, Reverse Type, Under-line)
Boolean Value (Normal, Reverse Type, Blinking)
Numeric Value (Normal, Scaling, Limit - Blink/Color/Text)
Message Value (Dynamic Message, Multi-language)
Button (Value, Title, Picture, Security, Confi rm, Password)
Picture (Static, Dynamic, Boolean Picture)
Login/Logout
Bar Meter (Vertical, Horizontal, Scale, Unipolar, Bipolar)
Trace (1-axis, 2-axis)
Trend (Real-time, Historical)
Schedule-Control
Gauge Meter
Alarm Lists
Data Logger (Log data; support USB export or FTP upload)
Built-in Various Objects (Button, Gif, LED... will be More)
Multi-language: English, Traditional Chinese, Simplify Chinese, Russian, etc.
Support user designed graphics, e.g. JPG, PNG ...
More at: Chapter 2.5 & FAQ www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC 
FAQ-146
Running HMI and Control Logic in the Same PAC

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
1-2
1.2 eLogger HMI Application
ICP DAS eLogger is an easy and useful HMI development tool which helps user to create
user-friendly pictures and control items. (Recommend to use Soft-GRAF HMI, the performance is
better. Please refer to Section 2.5.)
More at: www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC FAQ-115

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
1-3
1.3 Redundant Communication System
More at www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC - 119
RS-485 or Ethernet redundant communication mechanism/applications.
For XP-8xx7-CE6, XP-8xx7-Atom-CE6, WP-8xx7 & VP-2xW7/4xx7 series.
1.4 New Hot-Swap and Redundant System
Please plug one I-8135W and enable the 2nd Ethernet port of VP-25W7/23W7/4137.
If one Ethernet cable is broken or damaged, the other one will still work.
If one controller is damage, the other one will take over the control of the RS-485 I/O.
PC/HMI can connect to this redundant system by one or two active IP.
More at www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC - 093

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
1-4
1.5 Modbus Master: RTU, ASCII, RS-232/485/422
Support up to 10 ports: COM2~COM3 & COM5~COM14 (if I-8112iW/ 8114W/ 8114iW/ 8142iW/
8144iW in Slot0 ~ 2)
Can link to Modbus PLC or M-7000 I/O or Modbus devices
(Power meter, temperature controller, inverter etc.)
1.6 Modbus Master: TCP/IP
Each ISaGRAF WinCE ViewPAC supports to link to max. 100 Modbus TCP/IP slave devices.
Support various Standard Modbus TCP/IP Slave devices.
More at www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC > FAQ-113

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
1-5
1.7 Modbus Slave: RTU/TCP
Modbus RTU (RS-232/485/422): max. 5 ports
Modbus TCP/IP: max. 32 connections
1.8 Communicate With Other TCP/IP Server or UDP Client/Server
Devices

ISaGRAF WinCE ViewPAC User Manual , V.1.6 , 1/2017 by ICP DAS
1-6
1.9 Multiple Web HMI Monitor & Control Everywhere!
1.10 Send Email with One Attached File
More at www.icpdas.com > Support > FAQ > ISaGRAF Soft-Logic PAC - 067