ICP DAS USA WISE-75 M Series User manual

ICP DAS WISE
User Manual for
WISE-2841M Series
[Version 1.0.0 - 2022/09/12]

ICP DAS WISE User Manual
http://wise.icpdas.com
2
Warning
The information furnished by ICP DAS Co. Ltd. (hereinafter “ICP DAS”) is accurate
and reliable to ICP DAS‟s best knowledge. ICP DAS reserves the right to change the
content of this manual at any time without notice.
Through the communication mechanisms provided by third-party companies (such as
LINE, WeChat, Amazon Web Services, Microsoft Azure, IBM Bluemix), this
controller can send the notification messages and information regarding this controller
to the related personal account or the third-party platform (function). However, this
function may not be available due to the third-party companies close or terminate the
communication mechanisms of their systems.
ICP DAS cannot guarantee that this controller is free of any actual or legal defects
(including but not limited to stability, reliability, accuracy, completeness, validity,
suitability for a specific purpose, security related defects, errors or bugs, infringement
of rights etc.). ICP DAS shall not be responsible for any damages inflicted upon users
in relation to the use of the controller.
Copyright and Trademark Information
© Copyright 2022 by ICP DAS Inc., LTD. All rights reserved worldwide.
Trademark of Other Companies
The names used for identification only maybe registered trademarks of their
respective companies.
License
The user can use, modify and backup this software on a single machine. The user may
not reproduce, transfer or distribute this software, or any copy, in whole or in part.

ICP DAS WISE User Manual
http://wise.icpdas.com
3
Table of Contents
1Introduction.............................................................................................14
2Before Installation...................................................................................22
3System Login..........................................................................................24
4WISE Web Page Overview.....................................................................26
4.1 System function area ...................................................................27
4.2 Sub-function area.........................................................................31
4.3 Data review/System setting area .................................................32
4.4 System and logic rule setting procedure......................................34
5System Setting .......................................................................................35
5.1 Time Setting.................................................................................36
5.2 Network Setting............................................................................37
5.3 Account Setting............................................................................39
5.4 Security Setting............................................................................41
5.5 SNMP Setting ..............................................................................46
5.6 VPN Setting .................................................................................49
5.7 DDNS Setting...............................................................................51
5.8 Others Setting..............................................................................52
5.9 COM Port Interface Setting..........................................................52
6Module Setting........................................................................................56
6.1 XV-Board Setting .........................................................................56
6.2 Remote I-7000/DL DCON Module Setting ...................................61
6.3 I-7000/DL DCON Module List Operation Interface.......................65
6.4 Remote Modbus RTU Module Setting..........................................71
6.5 Modbus RTU Module List Operation Interface.............................74
6.6 Remote Modbus TCP Module Setting..........................................93
6.7 Modbus TCP Module List Operation Interface .............................94
6.8 IP Camera Setting........................................................................95
6.9 IP Camera List Operation Interface..............................................97
7Logger Setting......................................................................................104
7.1 I/O Module Data Logger Setting.................................................105
7.2 User-Defined Data Logger.........................................................108
7.3 MQTT Data Logger Setting........................................................ 111
7.4 Event Logger Setting .................................................................112
7.5 FTP Server Setting ....................................................................113
7.6 The Path of Data Log File..........................................................115
8IoT Platform Setting..............................................................................118

ICP DAS WISE User Manual
http://wise.icpdas.com
4
8.1 AWS Platform Setting ................................................................119
8.2 Microsoft Azure Platform Setting................................................127
8.3 IBM Bluemix Platform Setting ....................................................132
8.4 MQTT Setting.............................................................................136
8.5 IoTstar Connection Setting.........................................................144
8.6 IoTstar Real-Time Data Sending Setting....................................146
8.7 IoTstar Historical Data Sending Setting......................................147
8.8 IoTstar Video Data Sending Setting ...........................................147
8.9 IoTstar Bot Service Message Setting .........................................149
9Advanced Setting .................................................................................151
9.1 Internal Register Setting ............................................................151
9.2 Timer Setting..............................................................................155
9.3 Schedule Setting........................................................................158
9.4 Email Setting..............................................................................161
9.5 SNMP Trap Setting ....................................................................164
9.6 CGI Command Setting...............................................................170
9.7 LINE Notify Setting.....................................................................176
9.8 Active I/O Sending Setting.........................................................184
9.9 Channel Status Setting ..............................................................188
9.10 Ping Setting................................................................................192
10 Rules Setting........................................................................................194
10.1 IF Condition Setting ...................................................................197
10.2 THEN/ELSE Action Setting........................................................222
11 Download to Module.............................................................................247
12 Upload from Module .............................................................................248
13 Channel Status.....................................................................................249
14 IP Camera Status..................................................................................253
15 Firmware Update..................................................................................254
16 Rule File Import & Export......................................................................258
Appendix I：Modbus Address Table............................................................261
Appendix II：Reset to Factory Default Setting and send password to
Administrator...........................................................................269
Appendix III：The configuration setting of ICP DAS modules......................276
Appendix IV：The support list of ICP DAS I/O modules..............................281
Appendix V：The format of CGI Query command.......................................286
Appendix VI：Change the value of output channel of I/O module or Internal
Register by MQTT protocol.....................................................302
Appendix VII：The JSON format for the communication with IoT Platform .305

ICP DAS WISE User Manual
http://wise.icpdas.com
5
Appendix VIII：WISE-523x / WISE-224x LED Indicators ............................309
Appendix IX：ICP DAS “IoTstar Trial” account application ..........................310

ICP DAS WISE User Manual
http://wise.icpdas.com
6
List of Figures
Figure 1-1：WISE-2841M System Architecture.............................................16
Figure 1-2：WISE-523x/WISE-224x IO module support list..........................17
Figure 3-1：The password setting page for first time login WISE..................24
Figure 3-2：WISE Login page.......................................................................24
Figure 4-1：WISE home page (login as an Administrator) ............................26
Figure 4-2：System Function Area (login as an Administrator) .....................27
Figure 4-3：Rules management toolbar (login as an Administrator)..............27
Figure 4-4：Rules management toolbar (login as an User)...........................27
Figure 4-5：Rules management toolbar (login as a Guest)...........................27
Figure 4-7：Confirm to clear settings ............................................................28
Figure 4-8：Confirm to load settings .............................................................28
Figure 4-9：Confirm to save settings.............................................................28
Figure 4-10：Confirm to logout (The settings are saved)..............................29
Figure 4-11：Confirm to logout (The settings are not saved) ........................29
Figure 4-12：Real-time information area.......................................................29
Figure 4-13：Real-time information list..........................................................30
Figure 4-14：Current function path................................................................31
Figure 4-15：Data review/System setting area (login as an Administrator)...32
Figure 4-16：Data review/System setting area (login as User or Guest).......33
Figure 4-17：System and logic rule setting procedure..................................34
Figure 5-1：System Setting Overview Page..................................................35
Figure 5-2：Time Setting Page......................................................................36
Figure 5-3：Time Synchronization Setting.....................................................36
Figure 5-4：Network Setting Page ................................................................38
Figure 5-5：Account Setting Page for Administrator......................................39
Figure 5-6：Account Setting Page for User...................................................40
Figure 5-7：Account setting Page for Guest .................................................41
Figure 5-8：Security Setting Page.................................................................42
Figure 5-9：Web Server Setting page...........................................................42
Figure 5-10：Local SFTP Server Setting Page .............................................43
Figure 5-11：Local FTP Server Setting Page................................................44
Figure 5-12：Local Modbus Server Setting Page..........................................44
Figure 5-13：CGI QueryAuthentication Setting Page...................................45
Figure 5-14：Blacklist and Whitelist Setting Page.........................................45
Figure 5-15：IP address Setting Page in Blacklist/Whitelist..........................46
Figure 5-16：Save and Download the Security Setting.................................46

ICP DAS WISE User Manual
http://wise.icpdas.com
7
Figure 5-17：SNMP Setting Page.................................................................47
Figure 5-18：SNMP V3 Setting Page............................................................47
Figure 5-19：SNMP V3 User Setting Page ...................................................48
Figure 5-20：SNMP V3 User Authentication & Encryption Setting Page.......48
Figure 5-21：VPN Setting Page....................................................................50
Figure 5-22：DDNS Setting Page .................................................................51
Figure 5-23：Decimal Place Number Setting Page.......................................52
Figure 5-24：COM Port Interface Setting Page.............................................52
Figure 5-25：COM Port Interface Setting for Modbus RTU Slave.................53
Figure 5-26：COM Port Interface Setting for DCON Master .........................53
Figure 5-27：COM Port Interface Setting for Modbus RTU Master...............54
Figure 6-1：Module Setting Page..................................................................56
Figure 6-2：XV-Board Setting Page..............................................................57
Figure 6-3：XV-Board DI Channel Setting Page ...........................................58
Figure 6-4：XV-Board DO Channel Setting Page .........................................59
Figure 6-5：XV-Board AI Channel Setting Page............................................60
Figure 6-6：XV-Board AO Channel Setting Page..........................................61
Figure 6-7：Remote I-7000/DL Module Setting Page....................................62
Figure 6-8：The “Scan” button to search I-7000/DL Modules........................62
Figure 6-9：Set up the Scanning Range for the I-7000/DL modules.............63
Figure 6-10：Scanning the I-7000/DL modules.............................................63
Figure 6-11：I-7000/DL module List after Scan operation.............................63
Figure 6-12：Select the actual I-7000/DL modules connected......................64
Figure 6-13：Set up the No. and Address of the I-7000/DL modules............64
Figure 6-14：Select the model of the I-7000/DL modules .............................64
Figure 6-15：Add the I-7000/DL Module manually........................................65
Figure 6-16：I-7000/DL Module List Operation Interface...............................65
Figure 6-17：I-7000/DL Module DI Channel Setting page.............................66
Figure 6-18：I-7000/DL Module DO Channel Setting page...........................68
Figure 6-19：I-7000/DL Module AI Channel Setting page.............................69
Figure 6-20：I-7000/DL Module AO Channel Setting page ...........................70
Figure 6-21：Remote Modbus RTU Module Setting page.............................71
Figure 6-22：The “Scan” button to search ICP DAS module.........................72
Figure 6-23：Set up the Scanning Range for the ICP DAS module..............72
Figure 6-24：Scanning the ICP DAS module................................................72
Figure 6-25：The ICP DAS module List after Scan operation.......................73
Figure 6-26：Select the actual ICP DAS modules.........................................73
Figure 6-27：Set up the No. and Address of the Modbus RTU modules.......74

ICP DAS WISE User Manual
http://wise.icpdas.com
8
Figure 6-28：Select the model of the Modbus RTU Module..........................74
Figure 6-29：Add the Modbus RTU Module manually...................................74
Figure 6-30：Modbus RTU module List Operation Interface.........................75
Figure 6-31：ICP DAS Modbus RTU module DI Channel Setting page........76
Figure 6-32：ICP DAS Modbus RTU module DO Channel Setting page ......77
Figure 6-33：ICP DAS Modbus RTU module AI Channel Setting page.........78
Figure 6-34：ICP DAS Modbus RTU module AO Channel Setting page.......79
Figure 6-35：Modbus RTU module Coil Output Setting page .......................80
Figure 6-36：Coil Output Setting Example for Modbus RTU module ............82
Figure 6-37：Modbus RTU module Discrete Input Setting page...................83
Figure 6-38：Discrete Input Setting Example for Modbus RTU module........84
Figure 6-39：Modbus RTU module Input Register Setting page...................85
Figure 6-40：Input Register Setting Example for Modbus RTU module........87
Figure 6-41：Modbus RTU module Holding Register Setting page...............89
Figure 6-42：Holding Register Setting Example for Modbus RTU module....90
Figure 6-43：Remote Modbus TCP I/O Module Setting page.......................93
Figure 6-44：Set up the Model/Name of the Modbus TCP Module...............94
Figure 6-45：Add the Modbus TCP Module manually...................................94
Figure 6-46：Modbus TCP I/O module List Operation Interface....................94
Figure 6-47：IP Camera Setting Page ..........................................................96
Figure 6-48：Set up the No, IP address and Port of the IP Cameras............96
Figure 6-49：Set up the Model Name of the IP Cameras..............................97
Figure 6-50：Add the IP Cameras.................................................................97
Figure 6-51：IP Camera List Operation Interface..........................................97
Figure 6-52：iCAM IP Camera Setting page.................................................98
Figure 6-53：iCAM IP Camera OSD Message Setting page.......................100
Figure 7-1：I/O Module Data Logger Setting Page .....................................105
Figure 7-2：The format of record data.........................................................106
Figure 7-3：FTP server selecting and setting page.....................................107
Figure 7-4：Email selecting and setting page..............................................108
Figure 7-5：User-Define Data Logger List Interface....................................109
Figure 7-6：User-Define Data Logger Setting Page....................................109
Figure 7-7：The setting interface of Real-time Variable Editor....................110
Figure 7-8：The view interface of Real-time Variable Editor........................ 111
Figure 7-9：MQTT Data Logger Setting page .............................................112
Figure 7-10：Event Data Logger Setting page............................................112
Figure 7-11：FTP Server List page..............................................................113
Figure 7-12：FTP Server Setting page........................................................114

ICP DAS WISE User Manual
http://wise.icpdas.com
9
Figure 8-1：Amazon Web Services Setting page........................................119
Figure 8-2："Device Data Endpoint" Setting page of Amazon Web Services
..............................................................................................................120
Figure 8-3：Certificate and Key Download page of Amazon Web Services 121
Figure 8-4："Thing ARN" page of Amazon Web Services ...........................122
Figure 8-5：Publish and Subscribe Setting page of Amazon Web Services123
Figure 8-6：Publish Message Setting Page of Amazon Web Services .......124
Figure 8-7：“User-Defined Data” Setting Page of Amazon Web Services...125
Figure 8-8：Subscribe Topic Setting Page of Amazon Web Services .........126
Figure 8-9：Receive messages in JSON format of Amazon Web Services 127
Figure 8-10：Microsoft Azure Setting page .................................................128
Figure 8-11：SAS Token generating interface on Azure IoT Explorer..........129
Figure 8-12：Microsoft Azure Publish/Subscribe Setting page....................130
Figure 8-13：MicrosoftAzure Publish Message setting page......................130
Figure 8-14：“User-Defined Data” Setting Interface of Microsoft Azure ......131
Figure 8-15：Microsoft Azure Subscribe Topic setting page........................132
Figure 8-16：IBM Bluemix Setting page......................................................133
Figure 8-17：IBM Bluemix Subscribe Message setting page......................134
Figure 8-18：MQTT setting page (Broker)...................................................136
Figure 8-19：MQTT Broker Parameter setting page...................................137
Figure 8-20：Publish Message and Subscribe Topic setting page..............139
Figure 8-21：Publish Message Setting Page ..............................................139
Figure 8-22：Publish User-Defined Message Setting Page ........................140
Figure 8-23：MQTT Subscribe Setting Page...............................................141
Figure 8-24：MQTT Subscribe Topic Setting Page .....................................141
Figure 8-25：MQTT Topic Import/Export setting page.................................142
Figure 8-26：The Export of MQTT Topic.....................................................143
Figure 8-27：The Import of MQTT Topic .....................................................143
Figure 8-28：IoTstar Connection Setting Page(1) .......................................144
Figure 8-29：IoTstar Connection Setting Page(2) .......................................145
Figure 8-30：IoTstar Connection Status......................................................145
Figure 8-31：IoTstar Real-Time Data Sending Setting page .......................146
Figure 8-32：Channel Names of Realtime data table of IoTstar database ..147
Figure 8-33：IoTstar Historical Data Sending Setting page.........................147
Figure 8-34：IoTstar Video Data Sending Setting page (1).........................148
Figure 8-35：IoTstar Video Data Sending Setting page (2).........................149
Figure 8-36：IoTstar Bot Service Message Setting page (1).......................150
Figure 8-37：IoTstar Bot Service Message Setting page (2).......................150

ICP DAS WISE User Manual
http://wise.icpdas.com
10
Figure 9-1：Internal Register List Page.......................................................153
Figure 9-2：Internal Register Setting page..................................................154
Figure 9-3：Timer Status and Actions..........................................................156
Figure 9-4：Timer List Page........................................................................157
Figure 9-5：Timer Setting page (by assign value).......................................157
Figure 9-6：Timer Setting page (by Internal Register).................................157
Figure 9-7：Schedule List Page..................................................................158
Figure 9-8：Calendar mode of Schedule setting.........................................159
Figure 9-9：Repeat mode of Schedule setting............................................160
Figure 9-10：Email List Page......................................................................161
Figure 9-11：Email setting page (Name & Description)...............................162
Figure 9-12：Email setting page (SMTP Server).........................................162
Figure 9-13：Email setting page (Email Address) .......................................163
Figure 9-14：Email setting page (Email Content)........................................163
Figure 9-15：SNMP Trap List Page.............................................................164
Figure 9-16：SNMPAgent Setting Page of V2c version .............................165
Figure 9-17：SNMPAgent Setting Page of V3 version ...............................165
Figure 9-18：SNMP Trap "Channel Data" type Setting Page......................166
Figure 9-19：List of "SNMP Trap Messages" edited by "Channel Data" type
..............................................................................................................167
Figure 9-20：SNMP Trap "User-Defined Data" type Setting Page..............167
Figure 9-21："User-Defined Data" Interface in Edit Mode...........................168
Figure 9-22："User-Defined Data" Interface in View Mode..........................169
Figure 9-23：SNMPAgent Setting Page(with SNMP Trap Message) .........169
Figure 9-24：CGI Command Server List Page............................................171
Figure 9-25：CGI Command Server Setting page.......................................171
Figure 9-26：CGI Command List Page.......................................................172
Figure 9-27：CGI Command (Sending) Setting page..................................173
Figure 9-28：CGI Command (Receiving) Setting page (1)..........................174
Figure 9-29：CGI Command (Receiving) Setting page (2)..........................175
Figure 9-30：CGI Command (Receiving) Setting page (3)..........................176
Figure 9-31：LINE Notify Message Setting page (1)...................................176
Figure 9-32：LINE Notify Message Setting page (2)...................................177
Figure 9-33：LINE Notify Message Setting page (3)...................................178
Figure 9-34：LINE Notify Message Setting page (4)...................................178
Figure 9-35：LINE Notify Forward Setting page(1) .....................................179
Figure 9-36：LINE Notify Forward Setting page(2) .....................................181
Figure 9-37：LINE Notify Chat Room Setting page (1) ...............................181

ICP DAS WISE User Manual
http://wise.icpdas.com
11
Figure 9-38：LINE Notify Chat Room Setting page (2) ...............................182
Figure 9-39：LINE Notify Chat Room Setting page (3) ...............................182
Figure 9-40：LINE Notify Chat Room Setting page (4) ...............................183
Figure 9-41：LINE Notify Chat Room Setting page (5) ...............................183
Figure 9-42：I/O Data Table Setting page (1)..............................................185
Figure 9-43：I/O Data Table Setting page (2)..............................................186
Figure 9-44：“Active Sending of I/O Data Table” Setting page (1)...............187
Figure 9-45：“Active Sending of I/O Data Table” Setting page (2)...............187
Figure 9-46：Channel Status List Page.......................................................188
Figure 9-47：Channel Status Setting Page .................................................189
Figure 9-48：Add a new group....................................................................189
Figure 9-49：Add I/O Channels into Group.................................................190
Figure 9-50：Multi-Groups Setting in User-defined Channel Status page...190
Figure 9-51：Tool bar of User-defined Channel Status page.......................191
Figure 9-52：Ping List Page........................................................................192
Figure 9-53：Ping Setting Page ..................................................................192
Figure 10-1：Rules overview page..............................................................194
Figure 10-2：Rules Setting page.................................................................195
Figure 10-3：DI condition setting page........................................................198
Figure 10-4：DI Counter condition setting page..........................................199
Figure 10-5：DO condition setting page......................................................202
Figure 10-6：DO Counter condition setting page........................................203
Figure 10-7：AI condition setting page........................................................204
Figure 10-8：Deadband parameter setting..................................................204
Figure 10-9：AI Deadband Operation (> or >= a numerical value)..............205
Figure 10-10：AI Deadband Operation (< or <= a numerical value)............206
Figure 10-11：AI Deadband Operation (= a numerical value).....................206
Figure 10-12：AO condition setting page....................................................207
Figure 10-13：Discrete Input condition setting page...................................208
Figure 10-14：Coil Output condition setting page .......................................208
Figure 10-15：Input Register condition setting page...................................209
Figure 10-16：Holding Register condition setting page...............................210
Figure 10-17：IP Camera's Event condition setting page............................211
Figure 10-18：CGI Receiving Command condition setting page.................211
Figure 10-19：AWS Connection Status condition setting page ...................212
Figure 10-20：AWS Subscribe Message condition setting page.................213
Figure 10-21：MicrosoftAzure Connection Status condition setting page...214
Figure 10-22：MicrosoftAzure Subscribe Message condition setting page 214

ICP DAS WISE User Manual
http://wise.icpdas.com
12
Figure 10-23：IBM Bluemix Connection Status condition setting page .......215
Figure 10-24：IBM Bluemix Subscribe Message condition setting page.....215
Figure 10-25：Broker Connection Status condition setting page.................216
Figure 10-26：Subscribe Topic condition setting page................................217
Figure 10-27：Connection Status condition setting page ............................217
Figure 10-28：Timer condition setting page................................................218
Figure 10-29：Schedule condition setting page ..........................................219
Figure 10-30：SD Card Status condition setting page.................................219
Figure 10-31：Internal Register condition setting page...............................220
Figure 10-32：Rule Status condition setting page.......................................221
Figure 10-33：Ping condition setting page..................................................221
Figure 10-34：DI Counter action setting page.............................................223
Figure 10-35：DO action setting page.........................................................224
Figure 10-36：AO action setting page.........................................................224
Figure 10-37：Infrared action setting page..................................................228
Figure 10-38：Coil Output action setting page............................................229
Figure 10-39：Holding Register action setting page....................................230
Figure 10-40：IP Camera's Snapshot action setting page ..........................231
Figure 10-41：IP Camera's Event action setting page ................................232
Figure 10-42：IP Camera's OSD Message action setting page..................232
Figure 10-43：AWS Function Status action setting page ............................233
Figure 10-44：AWS Publish Message action setting page..........................233
Figure 10-45：AWS Reset Variable action setting page..............................234
Figure 10-46：MicrosoftAzure Function Status action setting page............234
Figure 10-47：MicrosoftAzure Publish Message action setting page .........235
Figure 10-48：Microsoft Azure Reset Variable action setting page .............235
Figure 10-49：IBM Bluemix Function Status action setting page ................236
Figure 10-50：IBM Bluemix Publish Message action setting page..............236
Figure 10-51：IBM Bluemix Reset Variable action setting page..................237
Figure 10-52：MQTT Broker Function action setting page..........................238
Figure 10-53：MQTT Publish Message action setting page........................238
Figure 10-54：MQTT Reset Topic action setting page ................................239
Figure 10-55：Timer action setting page.....................................................239
Figure 10-56：Email action setting page.....................................................240
Figure 10-57：CGI Command Send action setting page.............................241
Figure 10-58：CGI Command Reset Variable action setting page..............241
Figure 10-59：Data Logger action setting page ..........................................242
Figure 10-60：SNMP Trap action setting page............................................242

ICP DAS WISE User Manual
http://wise.icpdas.com
13
Figure 10-61：LINE Notify action setting page............................................243
Figure 10-62：IoTstar Bot Service action setting page................................243
Figure 10-63：Reboot system action setting page......................................244
Figure 10-64：Internal Register action setting page....................................244
Figure 10-65：Rule Status action setting page............................................245
Figure 10-66：Delay action setting page.....................................................246
Figure 11-1：“Save” button of Rules management toolbar..........................247
Figure 11-2：Confirm to save settings.........................................................247
Figure 11-3：Save settings successfully .....................................................247
Figure 12-1：“Load” button of Rules management toolbar..........................248
Figure 12-2：Confirm to load settings .........................................................248
Figure 12-3：Load settings successfully .....................................................248
Figure 13-1：Channel Status page..............................................................249
Figure 13-2：Event List page ......................................................................250
Figure 13-3：Log File List page...................................................................250
Figure 13-4：CGI file list page by “List”format...........................................251
Figure 13-5：CGI file list page by “Thumbnail”format................................251
Figure 13-6：Ping Status page....................................................................252
Figure 13-7：Modbus Mapping Table page.................................................252
Figure 14-1：IP Camera Status and Event List page ..................................253
Figure 15-1：Firmware Update Setting page...............................................255
Figure 15-2：Firmware Update (1)..............................................................256
Figure 15-3：Firmware Update (2)..............................................................256
Figure 15-4：Firmware Update (3)..............................................................256
Figure 15-5：Firmware Update (4)..............................................................257
Figure 15-6：Firmware Update (5)..............................................................257
Figure 16-1：Export/Import Setting page and the settings to be backed up258
Figure 16-2："Export Settings" and "Export Certificates" message windows
..............................................................................................................259

ICP DAS WISE User Manual
http://wise.icpdas.com
14
1 Introduction
WISE-2841M Advanced version IIoT Edge Controller is an Intelligent Web-based
Multi-functions PAC controller designed by ICP DAS that functions as control units
for use in remote logic control and monitoring in various industrial applications.
WISE offers a user-friendly and intuitive HMI interface that allows you to implement
control logic on controllers just a few clicks away; no programming is required. With
this powerful and easy-to-use software, it will minimize the learning curve, shorten
time to market and dramatically reduce the labor and cost spent on system
development.
WISE-2841M is equipped with iMX8 cpu module, which can meet the requirements
of low power consumption and high performance computing power for the embedded
system, and are competent for the complex operations of edge computing and data
logging. WISE-2841M also can store a large amount of log data and image data with
the eMMC memory and MicroSD expansion slot that can be expanded to 2TB.
Through Web browser, you can access Web Server on WISE to perform tasks such as
logic rule edition and download. WISE equips an IF-THEN-ELSE rule engine that
will check whether the rules are valid or not and determine the execution of actions
under specific conditions, for examples: setting up I/O channel values, perform
scheduled and Timer tasks, sending Email under a specific condition. In addition,
through the Modbus TCP/RTU protocol and SNMP protocol, it enables SCADA
software or SNMP Management software to control and monitor I/O channel or
system status on controllers in real time.
In order to meet the requirement of high level information security protection of the
IoT(Internet of Things) system, WISE-2841M provides a variety of encrypted
communication protocols as below. With the HTTPS protocol supported by
WISE-2841M, users can securely access the WISE web page without worrying about
the setting being stolen. Through the SNMP v3 protocol, WISE-2841M can be
perfectly integrated with the IT and Network management system. Users can securely
download data log files stored from WISE through SFTP and FTPS protocols. In each
communication protocol WISE supports, users can set up the relevant protection
password or encryption certificate respectively. In addition, WISE-2841M supports
the setting of blacklist and whitelist, which allows users to filter and block the specific
domains. WISE-2841M also support the dynamic blacklist function to automatically
add the IPs which try to login WISE and get failure many times to the blacklist to

ICP DAS WISE User Manual
http://wise.icpdas.com
15
prevent the controller from the attack of password cracking. With the equipped VPN
function, WISE-2841M can connect to devices in a specific secure network domain to
completely isolated from the threats of information security outside.
WISE-2841M provides supports in I/O functions. It supports XV-board; allows
connections to I-7000 I/O modules, Modbus RTU Slave modules and Modbus TCP
Slave modules together. The wide range of selection options enables the flexibility in
I/O module integration to meet the requirements from various applications.
WISE-2841M provides Data Logger function to record the I/O channel data by
periodic cycle or event trigger. And it allows to send the data files by FTP or Email to
the control center.
In addition to inherit the features from the original WISE series controllers,
WISE-2841M Advanced version IIoT Edge Controller also provides many advanced
functions. About the Internal Register, WISE-2841M still support the 32-bit data
format and the editing of mathematical formula, but add the new data formats such as
64-bit long, Double and String, and all Internal Register support the “Retain Variable”
mechanism. For the floating-point sensor data which WISE get from sensor, user can
set up its decimal point to 1~4 digits for the SCADA software interfaces to provide
the flexibility for the appearance and accuracy of the sensor data.
In the integration with network devices, WISE-2841M provides CGI command
sending and receiving functions for the two-way interaction with IP Camera or other
programs; WISE-2841M also supports MQTT protocol to connect with MQTT Broker
for message publish and subscribe operations. In addition, WISE-2841M supports the
communication operation with the Instant Messaging Sending Software such as LINE
and WeChat, which can send the messages to the LINE accounts and WeChat
accounts user assign.
In the integration with Cloud Platform, WISE-2841M can connect to the IoT services
of Amazon Web Services, Microsoft Azure and IBM Bluemix cloud platforms. It also
can integrate with the IoTstar Cloud Management software provided by ICP DAS.
Based on the powerful integration capabilities with IT/IoT network environment, it
make WISE-284x series modules as the best IIoT Edge controller in the IoT Age.

ICP DAS WISE User Manual
http://wise.icpdas.com
16
Figure 1-1：WISE-2841M System Architecture
WISE-2841M system features:
IF-THEN-ELSE logic rules execution ability
WISE-2841M equips with an IF-THEN-ELSE logic Rule Engine; it offers
IF-THEN-ELSE rules for you to set up the logic content. After completing rule
edition and downloading rules to the WISE controller, the Rule Engine will loop
execute the rules in order under specific conditions.
No programming is required to implement logic content on controllers
WISE-2841M provides user-friendly Web UI pages for editing control logic on
the controllers. It enables to implement logic edition by a few clicks on the
mouse to set up and deploy logic rules without writing a single line of code.
No extra software tool is required; all operations can be done through the
Web browsers
Provides Web-based HMI interface runs on regular Web browsers. To edit
control logic, it only requires a browser to connect to the Web server on
WISE-2841M. No extra software tool installation is needed on the target PC.
Support various I/O Modules
WISE-2841M allows to connecting with a wide range of the ICP DAS I/O

ICP DAS WISE User Manual
http://wise.icpdas.com
17
modules as XV-Board, I-7000 modules, M-7000 modules, (P)ET-7000 modules,
WISE-7100 modules, WF-2000 modules and tM/DL/LC/IR/iSN series modules.
In addition to these ICP DAS modules, WISE-2841M also allows to connect
with devices that support Modbus RTU/TCP Slave protocol for I/O monitoring.
The ability to connect with various types of I/O modules enables flexibility and
scalability for system implementation and allows to meet various requirements
from the clients that enable to find best solutions to meet the requirements.
Please refer to the following table for I/O modules support list of WISE-2841M:
I/O Module Support List
Description
Amount
Local I/O
Module
Local Bus
ICP DAS：XV-Board series module
1
Remote I/O
Module
DCON
by RS-485
ICP DAS：I-7000/DL series module
Up to 16
modules (Each
COM Port)
Modbus RTU
by RS-485
ICP DAS：M-7000/tM/DL/LC/IR/iSN series
module.
Others：The modules which support the
Modbus RTU Slave Protocol.
Modbus TCP
by Ethernet
ICP DAS：WISE-7100/(P)ET-7000/
WF-2000 series module
Others：The modules which support the
Modbus TCP Slave Protocol.
Up to 16
modules
IP Camera
HTTP
by Ethernet
iCAM-ZMR8422X, iCAM-MR6422X,
iCAM-MR6322
Up to 12
cameras
Figure 1-2：WISE-523x/WISE-224x IO module support list
Connection with IPCamera
WISE-2841M allows connections to ICP DAS iCAM IP Camera series. Users
can trigger the connected IP camera to perform snapshot or video recording with
IF-THEN-ELSE logic rules. WISE-2841M provides the IP Camera Status
webpage to display the event list ordered by time, and you can just click and play
the images or videos on the browser. In additional, WISE-2841M provides
remote backup mechanism to upload images and videos to the remote FTP server
automatically.
Data Logger function
With the microSD card, WISE-22841M provides Data Logger function to
real-time record the I/O data of the controller. The Data Log files can be sent to

ICP DAS WISE User Manual
http://wise.icpdas.com
18
the FTP server or the Email address for users, or user can actively download
them from the FTP client utility or Web page for further administration
management or data analysis.
Internal Register (Perform Math formula, Retain Variable, String
processing)
WISE-2841M provides Internal Registers function; it can be used to hold
temporary variables and perform math operation. About the math formula
performing, it supports to insert I/O channels to be the variables, and use the
operators such as plus“+”, minus“-”, times“*”, divide“/”, superscript“^”, left
parenthesis “(” and right parenthesis“)” to complete the editing of formula. Users
can edit different formula in each Internal Register, then WISE will calculate the
results of all formulas repeatedly, and save the results into the corresponding
Internal Registers for IF-THEN-ELSE rule checking or data logging. Internal
Register also provides "Retain Variable" mechanism. It means the data inside the
Internal Registers can be retained even the WISE is in Power Off status. In
addition, the Internal Register also supports the String editing operation. The
result of the string editing of the Internal Register can be used as the content for
the WISE's E-mail and Instant Message sending functions.
Provide Timer and Schedule operation
WISE-2841M features two kinds of timing functions: Timer and Schedule. It
allows you to perform specific tasks such as time delay, or schedule specific date
or time for control logic execution. To ensure the accuracy of the WISE
controller clock, it also has the ability to sync the clock to an SNTP time server
for time synchronization through the network.
Provide Email Alarm message sending function
WISE-2841M supports Email alarm message sending function. Email is the
important function for real-time message communication. The sending action can
be added to the logic edition as part of logic control to provide real-time message
transmission in response to specific events. The SSL authentication is provided
by WISE-2841M.
Provide CGI Command Sending and Receiving functions
CGI command function is an important function for real-time message
communication in network environment. WISE-2841M supports fully CGI
command operations as CGI command sending and CGI command receiving.

ICP DAS WISE User Manual
http://wise.icpdas.com
19
The CGI command sending action can be added to the logic edition as part of
logic control in response to specific events. The CGI command receiving
function let WISE-2841M can receive the CGI command from others network
devices. The content of CGI command receiving can be used in IF condition
statements to trigger the THEN/ELSE actions.
Real-time monitoring system status of controllers
WISE-2841M supports Modbus TCP/RTU Protocol for you to perform real-time
monitoring and control of the controllers. WISE also provides an easy-to-view
HMI web interface for real-time monitoring. It allows you to get important real
time system information even without SCADA software. Besides Modbus
TCP/RTU Protocol, WISE-2841M supports SNMP V2c and V3 protocols, and
provides the IF-THEN-ELSE rule setting to trigger the SNMP Trap sending. It
makes the integration between the Network Management software (and device)
and WISE-2841M to be easier.
Password protection for access control
WISE HMI web page offers password protection. After getting in the webpage,
you will be required to input the password before editing logic rules. In addition,
WISE-2841M provides monitoring web pages specifically designed for cell
phone. The access control restricts the access to the webpage to prevent
unauthorized modification; it allows to set up passwords for Administrator, User
and Guest; only the authorized users will be allowed to review the setting,
change the setting or modify the channel data.
HTTPS, SFTP, FTPS encrypted communication protocols support
WISE-2841M supports the encrypted communication protocols such as HTTPS,
SFTP, FTPS, etc…. It allow users to set up the secure communicatoin channel
for the data transmission of web pages content, sensor data and system
information with WISE-2841M.
VPN function support
WISE-2841M supports 4 VPN protocols such as PPTP, L2TP, OpenVPN and
SoftEther. By using the functuion, users can set up WISE-2841M to operate in a
secure closure network domain to protect WISE-2841M and the sensors it
connect from the intrusion of the external threats.

ICP DAS WISE User Manual
http://wise.icpdas.com
20
Active I/O Sending function
In addition to the Modbus TCP/RTU Slave function that enables SCADA
software (or HMI device) to poll the I/O channels value of the WISE controller,
now WISE-2841M provide the function “Active I/O Sending”for users. Based
on the “Active I/O Sending”function, WISE-2841M can send the I/O channels
value of the controller actively to SCADA software (or HMI device) by event
trigger (I/O channel value changed) or periodic cycle. This function will improve
the efficient of the data communication between WISE-2841M and SCADA
software (and HMI device). Please note: The SCADA software (or HMI device)
must equip the Modbus TCP Slave function to receive the I/O channels data sent
by WISE-2841M.
MQTT Message Publish/Subscribe operation
WISE-2841M supports the MQTT protocol. It can publish the I/O data of the I/O
module which connect to WISE-2841M to the MQTT broker, and receive the
message content of the Subscribe MQTT Topics which is published by others
MQTT device for the data logging operation or using it in the IF-THEN-ELSE
logic rule.
Connection with IoT Cloud Platform
WISE-2841M support the connection ability with the IoT Cloud Platform as
Amazon Web Services, Microsoft Azure, IBM Bluemix, etc. It work as the
concentrator in the IoT application to connect with Sensors and I/O modules,
collect and transfer the I/O channel data to the Cloud platform for future data
analysis. WISE-2841M also can receive the message which is published from the
Cloud platform for the corresponding actions at the field side.
Connect with IoTstar Cloud Management Software
WISE-2841M supports the connection with IoTstar Cloud Management software
developed by ICP DAS. Through the function of IoTstar, the sensor data and
image files uploaded from WISE-2841M can be automatically imported and
integrated, and the remote monitoring dashboard can be easily created to perform
the remote monitoring and maintenance operation.
Provide LINE Notify message sending function
WISE-2841M supports to send LINE messages to the LINE personal account or
group chat room. The LINE message sending function can be triggered by
IF-THEN-ELSE rules. The LINE message content could be a preset string with