ICP DAS USA PCI-1202 Series User manual

PEX-1202 and PCI-1202/1602/180x Series Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The package includes the following items:
One PCI-1202/1602/180x series board as follows:
PEX-1202L/1202H, PCI-1202LU/1202HU
PCI-1602U/1602FU
PCI-1800LU/1800HU, PCI-1802LU/1802HU
One Software Utility CD (V5.2 or later)
One Quick Start Guide (This Document)
One CA-4002 D-Sub connector
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
For PEX-1202 Series
PCI-1202/1602/180x Series
What’s in the shipping package?
English/ Oct. 2013/ Version 1.2
Installing Windows Driver

PEX-1202 and PCI-1202/1602/180x Series Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The PCI-1202/1602/180x series classic driver supports Windows 98/NT/2K
and 32-bit XP/ 2003/ Vista/7/8. Recommended to install this driver for
have been used PCI-1202/1602/180x series boards of regular user, please
refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pci-180x/manual/quicksta
rt/classic/
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
Jumper Setting
1
2
3
4
5
1. CON3: Analog Input/Output
2. CON2: Digital Input
3. CON1: Digital Output
4. JP1: A/D Input Type Selection
5. J1: D/A Reference Voltage Selection
6. SW1: Card ID Setting
6

PEX-1202 and PCI-1202/1602/180x Series Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Please make sure JP1 jumper and SW1 is kept in default setting before
self-test, as follows:
Jumper
JP1: Analog Input Type Selection
SE
DIFF
1 2
5 6
JP1
SE
DIFF
JP1 1 2
5 6
Single-Ended Inputs (Default)
Differential Inputs
Switch
SW1: Card ID Setting
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI/PCI Express slot.
Step 4: Carefully insert your I/O card into the PCI/PCI Express slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
Installing Hardware on PC
Card ID
1
ID0
2
ID1
3
ID2
4
ID3
(*) 0
ON
ON
ON
ON
1
OFF
ON
ON
ON
2
ON
OFF
ON
ON
:
:
:
:
:
0xD
OFF
ON
OFF
OFF
0xE
ON
OFF
OFF
OFF
0xF
OFF
OFF
OFF
OFF
(*) Default setting

PEX-1202 and PCI-1202/1602/180x Series Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Pin Assignments

PEX-1202 and PCI-1202/1602/180x Series Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
DIO Test Wiring:
1. Use CA-2002 (optional) to connect the CON1 with CON2.
Analog Input Test Wiring:
2. Prepare for device:
DN-37 (optional) Wiring terminal board.
Provide a stable signal source. (For example, dry battery)
3. Connect a DN-37 to the CON3.
Self-Test

PEX-1202 and PCI-1202/1602/180x Series Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
4. Wire the signal source to channel 0, and then keep set the JP1 jumper to
Single-Ended (page 3), and wire the signals as follows:
The PEX-1202 and PCI-1202/1602/1802 Series:
Connect the AI 0 (Pin01) to signal positive (+)
Connect the A.GND (Pin17) to signal negative (-)
The PCI-1800 Series:
Connect the AI 0 (Pin01) to signal positive (+)
Connect the A.GND (Pin09) to signal negative (-)
5. Execute the UniDAQ Utility Program.
This program (UniDAQ Utility) will be placed in the
default path after completing installation.
The UniDAQ Utility.exe is located in (Default path):
C:\ICPDAS\UniDAQ\Driver\
Click this button
to start test.
3
Confirm the PEX-1202, PCI-1202/1602/180x
series card had successfully installed to PC. It
starts from 0.
2
Double-Click
1

PEX-1202 and PCI-1202/1602/180x Series Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
6. Get DIO function test result.
Select the “Port 0”
8
The corresponding D/I becomes red for
channel 0, 2, 4, 6 of D/O is ON.
9
Click “Digital Input”item.
7
Select the “Port 0”.
Check channel 0, 2, 4, 6
6
5
Click “Digital Output” item.
4
PASS

PEX-1202 and PCI-1202/1602/180x Series Quick Start Guide ICP DAS CO., LTD.
8
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
7. Get A/D function test result.
PEX-1202 and PCI-1202/1602/180x Series Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-1202.html
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-1602.html
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-1800.html
DN-37, CA-3710 and CA-2002 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information
Click this button to start test.
12
Check analog input on Channel 0 textbox.
The other channels value for floating
number.
13
Confirm the configuration setting.
11
PASS
Click “Analog Input”item.
10