ICP DAS USA PCI-P8R8 User manual

PCI-P8R8/P16R16 Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The package includes the following items:
One PCI-PxRx series board as follows:
PCI-P8R8
PCI-P16R16
One Software Utility CD (V5.2 or later)
One Quick Start Guide (This Document)
-
One CA-4037B Cable for
One CA-4002 D-Sub connector
Two CA-4002 D-Sub connectors
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
For PCI-P8R8/P16R16
What’s in the shipping package?
English/ Jun. 2013/ Version 1.2
Installing Windows Driver

PCI-P8R8/P16R16 Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The PCI-P16R16 Series classic driver supports Windows 98/NT/2K and
32-bit XP/ 2003/ Vista/7/8. Recommended to install this driver for have
been used PCI-P16R16 series boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pci-p16r16/manual/quicks
tart/classic/
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI slot.
Step 4: Carefully insert your I/O card into the PCI slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
Installing Hardware on PC

PCI-P8R8/P16R16 Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Pin Assignments
Note:
NO: Normal Open
COM: Common
NC: Normal Close
DIA: Digital Input (Point A)
DIB: Digital Input (Point B)
Extension Cable (CA-4037B):
DB-40-Pin conversion DB-37-Pin

PCI-P8R8/P16R16 Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Prepare for device:
DN-37 (optional) wiring terminal board.
Exterior power supply device. For example: DP-665 (optional)
Self-test wiring as follows:
1. Use the DN-37 to connect the CON1 on board.
2. Connect the NO(0-7) with DIA(0-7).
(Pin1/4/7/20/23/25/27/10 connects to Pin12/13/14/15/16/17/18/19).
3. Power Supply (+24 V) connects to COM0…COM7 (Pin2/5/8/21/24/26/28/11).
4. Power Supply GND connects to GND (Pin29).
Power Supply GND connects to DIB0…DIB7 (Pin30/31/32/33/34/35/36/37).
Self-Test

PCI-P8R8/P16R16 Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
4. Execute the UniDAQ Utility Program.
This program (UniDAQ Utility) will be
placed in the default path after
completing installation.
The UniDAQ Utility.exe is located in:
C:\ICPDAS\UniDAQ\Driver\
(Default path).
5. Get DIO function test result.
Double-Click
1
Select the “Port 0”
Check channel 0, 2, 4, 6
6
5
Confirm the PCI-P8R8/P16R16
series card had successfully
installed to PC. It starts from 0.
2
Click this button
to start test.
3
Click “Digital Output” item.
4

PCI-P8R8/P16R16 Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
PCI-P8R8 and PCI-P16R16 Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-p8r8.html
DN-37, CA-3710 and DP-665 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Select the “Port 0”
8
The corresponding D/I becomes black for
channel 0, 2, 4, 6 of D/O is ON.
9
Click “Digital Input”item.
7
Related Information
PASS