ICP DAS USA PISO-P32A32U-5V Series User manual

PEX-P32A32/PISO-P32A32U Series Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The package includes the following items:
One PEX-P32A32 or PISO-P32A32U (-5V) PCI Board.
One Software Utility CD (V6.2 or later)
One Quick Start Guide (This Document)
One CA-4037B Cable
Two CA-4002 D-Sub connectors
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it is
recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
The PISO-DIO Series classic driver supports Windows 98/NT/2K and 32-bit XP/2003/
Vista/7/8. Recommended to install this driver for have been used PISO-DIO series
boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/quickstart/
classic/
For PEX-P32A32
PISO-P32A32U(-5V) Series
Check the Supplied Items
Installing the Windows Driver
English/Jun. 2015/Version 1.1

PEX-P32A32/PISO-P32A32U Series Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Step 2: Click the “Next>” button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the “Next>” button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ, confirm and click the
“Next>” button.
Step 5: Check your DAQ Card on list, then click the “Next>” button.
Step 6: Click the “Next>” button on the Select Additional Tasks window.
Step 7: Click the “Next>” button on the Download Information window.
Step 8: Select “No, I will restart my computer later” and then click the “Finish” button.
For detailed information about the driver installation, please refer to Chapter 2.1 “Getting the
UniDAQ Driver DLL Installer package” of the UniDAQ SDK user manual.
Please make sure JP1 and JP2 jumper is kept in default setting before self-test, as follows:
(This example uses this power supply.)
Jumper
JP1/JP2
Internal Power

External Power
(Default Setting)
1. CON1: The Connector for DI <0…15> and DO<0…15>. Refer to Section 6 Pin Assignments.
2. CON2: The Connector for DI <16…31> and DO<16…31>. Refer to Section 6 Pin Assignments.
3. SW1: DIP Switch used to configure the Board ID. Refer to PISO-P32x32/x64 Series User
Manual.
4. JP1: Used to set the Internal or External Power for DI <0…15> on CON1, as above table.
5. JP2: Used to set the Internal or External Power for DI <16…32> on CON2, as above table.
Jumper Setting






PEX-P32A32/PISO-P32A32U Series Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Step 1: Shut down and power off the computer.
Step 2: Remove all the covers from the computer.
Step 3: Select an unused PCI Express/PCI slot.
Step 4: Carefully insert your card into the PCI Express/PCI slot and secure the board in place.
Step 5: Replace the covers on the computer.
Step 6: Reconnect the power supply and power on the computer.
Step 7: Once the computer reboots, follow any messages that may be displayed to complete
the Plug and Play installation procedure.
Step 8: Open the “Device Manager” in the Control Panel and verify that the PEX/PISO-P32A32
Series board is listed correctly.
If your control device is an inductive load (ex: inductive relay), it is recommended to connect a diode
at the Control Device side as a means of preventing damage from the counter EMF.
To prevent the board damaged forever by overload, the GND pins (CON1: pin 1/20, CON2: pin
1/20) all must be connected with GND of External Power.
Wiring Note
Installing the Hardware

PEX-P32A32/PISO-P32A32U Series Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Pin Assignments
Extension Cable (CA-4037B):
DB-40-Pin conversion DB-37-Pin

PEX-P32A32/PISO-P32A32U Series Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Prepare for device:
DN-37 (optional) wiring terminal board.
Exterior power supply device. For example: DP-665 (optional)
Self-test wiring as follows:
Step 1: Connect the DN-37 to the CON1 connector on your board using the CA-3710 cable.
Step 2: Keep set the JP1 and JP2 jumper to External Power (See Section 3 Jumper Setting).
Step 3: Connect the DI(0-15) with DO(0-15).(DI0 connect to DO0 … DI15 connect to DO15)
PEX-P32A32 and PISO-P32A32U External Power Wiring:
Step 4: Connect the Power Supply (+24 V) to Ext.PWR0 (Pin37).
Connect the Power Supply GND to ECOM0 (Pin18).
Connect the Power Supply GND to Ext.GND0 (Pin1 and Pin20).
PISO-P32A32U-5V External Power Wiring:
Step 4: Connect the Power Supply (+5 V) to Ext.PWR0 (Pin37).
Connect the Power Supply GND to ECOM0 (Pin18).
Connect the Power Supply GND to Ext.GND0 (Pin1 and Pin20).
Self-Test
The PEX-P32A32/PISO-P32A32U suggests input voltage range as follow:
Logic high: +9 ~ +24 V; Logic Low: 0 ~ 1V.
(Higher voltage over the limitation will cause the hardware damage.)
The PISO-P32A32U-5V suggests input voltage range as follow:
Logic high: +5 ~ +12 V; Logic Low: 0 ~ 1V.
(Higher voltage over the limitation will cause the hardware damage.)

PEX-P32A32/PISO-P32A32U Series Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The PEX-P32A32/ PISO-P32A32U wiring is illustrated in the figure below:
DN-37 I/O Wiring
GND
GND
+5V
13 4 5 6 7 8 9 10 11 13 14 17 15 16 18
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
12
2
+24V
37
19
External: DP-665
CON1
Cable: CA-3710
The PISO-P32A32U-5V wiring is illustrated in the figure below:
DN-37 I/O Wiring
GND
GND
+5V
13 4 5 6 7 8 9 10 11 13 14 17 15 16 18
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
12
2
+24V
37
19
External: DP-665
CON1
Cable: CA-3710

PEX-P32A32/PISO-P32A32U Series Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
Step 5: Execute the UniDAQ Utility Program.
1. In Windows 7, click the “Start” button, point
to “All Programs”,and then click the
“ICPDAS”folder. Point to “UniDAQ
Development Kits”and then click the
“UniDAQ Utility”to execute the UniDAQ
Utility Program.
2. Confirm that PEX/PISO-P32A32 Series board
has been successfully installed in the Host
system. Note that the device numbers start
from 0.
3. Click the “TEST”button to start the test.
Step 6: Check the results of the DIO function test.
1. Click the “Digital Output”tab.
2. Select “Port0”from the “Port Number”drop-down menu.
3. Check the checkboxes for channels 0, 2, 4 and 6.




PEX-P32A32/PISO-P32A32U Series Quick Start Guide ICP DAS CO., LTD.
8
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
4. Click the “Digital Input”tab.
5. Select “Port0”from the “Port Number”drop-down menu.
6. The DI indicators will turn black when the corresponding DO channels 0, 2, 4 and
6 are ON.
PEX-P32A32 and PISO-P32A32U(-5V) Series Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/piso-p32a32u.ht
ml
DN-37, CA-3710 and DP-665 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information


Note:
All the DI should become red because all the DO is OFF
(uncheck).
